key GEELY FC 2008 Owner's Manual

Anti-stealing and door lock--Electronic anti-stealing system
Electronic anti-stealing system
Electronic anti-stealing system consists of anti-stealing controller, anti-stealing loop and transmitter. One
end of loop covers ignition locker core, the other end connects with anti-stealing controller, and the other end
of controller connects with engine ECU, at the same time, transmitter is assembled in key. Memory of
transmitter stores only mark (code) showing the legal identity of automobile owner, transmitter, anti-stealing
controller and electric injection ECU constitutes a multi-layer effective electronic anti-stealing system verified
by password.
If customer key loses, anti-stealing ECU is changed or engine ECU is changed, it is necessary to match
again in repairing station. When automobile leaves the factory, safety password is delivered directly to
owner for keeping with the type of secrecy. If it is necessary to make a new key, change anti-stealing
controller and make other operations, owner should bring the safety password with the automobile to repair
in repairing station. Repairing station should keep repairing (make new key, change anti-stealing controller
and so on) record for inquiring in future.
 361 

Electric sunroof (optional)--Sunroof system
Inspection for sunroof function
1. Inspection for sliding opening function.
(1) Turns ignition switch to ON, when spot contacting sunroof
switch keystroke 2, the sunroof will start automatic sliding
opening work, and it does not stop until it is at complete
opening state. If spot contacting it in running process, or
pressing keystroke 1 or 2 for long time, sunroof glass will
stop running immediately.
(2) Turns ignition switch to ON, when pressing keystroke 2 for
Sunroof system
Specification for sunroof function
1. Operation category
Spot contact: press the keystroke one time, then release immediately (the time is less than 0.3 seconds).
Long press: press the key stroke for long time (the time is more than 0.3).
2. Specification for function.
Anti-clamping function: spot contact the keystroke to make the sunroof could face 10 Kg resistance in the
process of closing from any position, at this time, electric motor turns oppositely, and the sunroof returns
turn-up or opening state.
Automatic closing function: when the key is pulled out from ignition locker, at this time, the sunroof is not
at closing state, it will close automatically in three seconds.
long time, the sunroof will start automatic sliding opening work, and it does not stop until it is at
complete opening state. If releasing keystroke 2 in running process, the sunroof glass will stop running
immediately.
2. Inspection for sliding closing function.
(1) Turns ignition switch to ON, if the sunroof is at opening state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically slide to closing state. If spot contacting it or pressing
keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at opening state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 1 in running
process, sunroof glass will stop running immediately.
3. Inspection for turn-up opening function
(1) Turns ignition switch to ON, if the sunroof is at closing state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically move to turn-up opening state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at closing state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to turn-up opening state. If releasing keystroke 1 in
running process, sunroof glass will stop running immediately.
4. Inspection for turn-up closing function
(1) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when spot contacting sunroof
switch keystroke 2, the sunroof will automatically move to closing state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when pressing sunroof switch
keystroke 2 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 2
in running process, sunroof glass will stop running immediately.
 364 
Front
Rear

Electric sunroof (optional)--Sunroof system
Inspection for sunroof switch
(a) Check the function of switch. Disassemble front top light,
and disassemble the joint of front top light, then check the
joint at the side of switch liking that shown in figure.
Malfunction phenomenon table Position of parts
Malfunction phenomenon
Sunroof system does not work
Sunroof system works abnormallyPossible malfunction part
1. Ignition switch.
2. Control switch of sunroof.
3. 25A, 15# fuse.
4. Wiring harness
1. Control switch of sunroof.
2. Wiring harnessReference page
-
-
-
-
-
-
 365 
Terminal connected by avometer
2-4
2-5ConditionSpot contact or press
keystroke 2 for long time
Spot contact or press
keystroke 1 for long time
Regulated situa-
tion
Conduction
Conductiion
Shell body of sunroof
Motor of sunroof
Switch of sunroof

Engine cover/automobile door--Front automobile door
8. Disassemble left front glass assembly [68000146]
Hint: insert the cloth in door steel board to prevent it from
scratching the glass.
(a) Turn the door glass until the bolts happens in repairing
hole.
(b) Disassemble two bolts and door glass.
Note: do not damage the door glass.
Hint: pull the door glass upwards to disassemble it.
9. Disassemble seal tape of left front glass guide slot
[68000161]
10. Disassemble left front door glass lift assembly
[67000122]
(a) Disassemble the joint.
(b) Disassemble six bolts and glass lift.
11. Spread lubricating grease on automobile body.
12. Disassemble left front door window glass guide
slot assembly [68000148]
Disassemble the screw and door framework rear lower bracket.
13. Disassemble left front door locker organization as-
sembly [68000152]
(a) Disassemble the joint.
(b) Disassemble connecting rod from exterior handle.
(c) Disassemble the bolt and screw.
(d) Use planetary socket wrench (T30) to disassemble three
planetary screws and door locker.
(e) Disassemble two screws and left front door locker organi-
zation driver.
14. Spread lubricating grease on automobile body.
Spread MP lubricating grease on sliding and turning parts of
lift assembly.
15. Disassemble left front door exterior handle pedestal.
(a) Use planetary socket wrench to disassemble the screw
and door key tank.
(b) Disassemble exterior handle from exterior handle pedestal.
(c) Use planetary socket wrench to disassemble the screw
and left front door exterior handle pedestal.
 370  16. Assemble left front door locker organization assembly [68000152]
(a) Use two screws to assemble left front door locker organization driver.
(b) Use planetary socket wrench (T30) to assemble three planetary screws and front door locker assembly.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
(c) Assemble the bolts and screws.
(d) Connect connecting rod to exterior handle.
(e) Connect the joint.

Automobile control system--Ignition switch and anti-versa lock key warning switch
Phenomenon
Ignition switch could not insert on any
positionPossible malfunction part
1. Ignition switch
2. Circuit of power supplyReference page
394
-
Automobile control system
Ignition switch and anti-versa lock key warning switch
Malfunction phenomenon table
Inspection
1. Check the ignition switch.
Check the conduction of ignition switch joint and terminal
If the conduction does not accord with the regulation, change
the switch.
2. Check the anti-versa lock key warning switch.
If the conduction does not accord with the regulation, change
the switch.
 394 
Position of switch Terminal connected by avometerRegulated situation
LOCK - Not conduction
ACC 1-3 Conduction
ON 1-2-3, 5-6Conduction
START 1-2, 4-5-6Conduction
Position of switch Terminal connected by avometerRegulated situation
OFF (key does not insert)- Not conduction
ON (key inserts)1-2 Conduction