wiring GEELY MK 2008 Owner's Manual

5-73Precautions:1. Don't operate refrigerant in confined space or near open fire.
2. Always wear eyeglass.
3. Be careful don't let liquid refrigerant contact your eyes and skin,
if liquid refrigerant contacts your eye or skin.
(a) Please wash with fresh water.
Warning:
Don't knead your eyes or scrub your skin
(b) Apply soft petroleum ointment on your skin.
(c) See doctor or go to hospital immediately for specialized
treatment.
4. Don't heat container or put it near open fire.
5. Be careful not to fall off, object should not touch container.
6. If there is no sufficient refrigerant in refrigerating system, don't
operate the compressor.
If there is no sufficient refrigerant in the system, insufficient oil
lubrication might cause burning out of compressor. Be careful to
avoid occurrence of such things.
7. When compressor runs, don't turn on pressure gauge high-pressure
valve.
If high-pressure valve is turned on, refrigerant will flow in reverse
direction, and cause bursting of refrigerant tank, so only low
pressure valve may be turned on or off.
8. Be careful to avoid excess refrigerant
Excess refrigerant will result in poor refrigerating capacity, worse
fuel economical efficiency, engine overheat etc problems.Symptom
Blower does not workSymptom table Use the following table to find out the cause of fault, number indicates probable priority of problem, check each
part according to priority, replace components if required.
Suspected Area
1.Blower fuse
2.Centralized controller fuse
3. Blower relay
4. Integrated control panel assembly (blower switch)
5. Blower adjustment resistor
6. Blower
7. Wiring harness.Air Conditioning System -General Information

Air Conditioning System -General Information5-74Symptom
No air temperature control
Compressor does not work
Insufficient refrigeration
No engine idle speed when air conditioning
switch is ON (switch on)
No air input control
No mode control
Condenser fan does not workSuspected Area
1. Engine coolant quantity
2. Air conditioning control mechanism assembly.
1. Refrigerant quantity
2. Compressor fuse
3. Centralized controller fuse
4. Magnetic clutch relay
5. Pressure switch
6. Magnetic clutch assembly
7. Air conditioning compressor assembly
8. Integrated control panel assembly (air conditioner switch)
9. Air conditioner thermistor
10. Engine ECU
11. Wiring harness
1. Refrigerant quantity
2. Refrigerant pressure
3. Driving belt
4. Air conditioner thermistor
5. Integrated control panel assembly (air conditioner switch)
6. Magnetic clutch assembly
7. Air conditioning compressor assembly
8. Condenser
9. Accumulator-drier
10. Expansion valve
11. Evaporator
12. Refrigerant line
13. Pressure switch
14. Air conditioner control mechanism assembly
15. Wiring harness
1. Idle speed control system
2. Wiring harness
3. ECM
1.Air conditioner control mechanism assembly
1.Air conditioner control mechanism assembly
1. MAIN fuse
2. Condenser fan fuse
3. Condenser fan relay
4. Condenser fan motor
5. Wiring harness

VIII. Circuit diagramVII. Check list index of fault without fault codeMK-60 ABS system -ABS Diagnosis5-101Fault condition
When Ignition switch is turned to "ON " (engine stall condition), ABS
warning lamp does not illuminate
After Engine is started, warning lamp does not go outCheck list No.
1
2
3
4
5
6Reference page
5-109
5-110
5-111
5-112
5-112
5-113 ABS works
abnormallyBraking force on both sides is not even
Braking force is insufficient
When brake pedal is stepped on slightly, ABS works
(automobile in idle state)
When brake pedal is stepped on slightly, ABS works
(automobile in running state)
When ABS works, brake pedal vibrates excessively
Travel of brake pedal is too long
A very large force is needed to step on brake pedal
No fault code output (cannot communicate with fault diagnosis instrument)Please Refer to "MK WIRING DIAGRAM"

3317
247
1632
17 6 5 4 3 2 1ABS ECU socket pin distribution (wiring harness end)
(1) ABS ECU socket (view of leading-out terminal) (3) Diagnosis connector (2) Trouble light driver module46
31
15MK-60 ABS system -ABS Diagnosis5-102

Abnormal
Replace HCUAbnormal
Replace HCUYes
Replace ABS ECUSection 2 ABS System CheckI. Check list of fault with fault codeNote: If storage battery is discharged excessively, it might fail to drive motor, so when conduct motor drive test,
firstly confirm whether voltage of storage battery is normal, when conduct motor drive test, vehicle must be in idle
state.MK-60 ABS system -ABS System Check5-103Fault code is 01276 1
[Description ] When vehicle speed exceeds 20 km/h, ABS ECU monitors that
motor can not work normally, it will record this fault code
[Prompt ] When this fault appears, wiring harness connection between motor
and ECU may get loose. Use hydraulic pressure unit functional
testing of fault diagnosis instrument to drive motor for this test.Possible cause

Power supply is discon-
nected or earthed

Motor wiring harness gets
loose

Motor is damaged
Pull out motor wiring harness plug, connect
battery power source directly to motor plug, see
whether motor works or not?
Check safety wire and ABS ECU joint
Connect motor wiring harness
Turn ignition switch to ON position
Eliminate fault code
Use fault diagnosis instrument to conduct
hydraulic control unit diagnosis
Whether fault recurs
Refer to "key points of occasional fault
repair"

Whether sensor is installed
correctlyYes
Install it correctlyCheck sensor output volt-
age at ABS ECU 25 chip
socketAbnormal
ReplaceCheck each wheel
speed sensorAbnormalReplace ABS ECUNormal
Replace or
repairCheck wheel bearing
clearanceAbnormalCheck wiring harnessbetween sensor andABS ECUNormalMK-60 ABS system -ABS System Check5-104Fault code is 00283, 00285, 00290, 00287 2
[Description ] when open circuit cannot be detected, there is no signal output
even if vehicle speed reaches above 20 km/h, this fault code
will appear.
[Prompt ] It is probably because that sensor is not mounted, sensor coil or
wiring harness is shorted, air gap between sensor and gear ring is
too large or gear ring is damaged.Possible cause

Sensor is not mounted

Sensor coil or wiring har-
ness is shorted

Air gap between sensor
and gear ring is too large

Gear ring is not mounted

ABS ECU fails
ReplaceCheck the pulse ringAbnormalNormal

Whether sensor is installed
correctlyYes
Install it correctlyCheck sensor output volt-
age at ABS ECU 25 chip
socketAbnormal
ReplaceCheck each wheel
speed sensorReplace ABS ECUNormal
ReplaceReplace or
repairCheck wheel bearing
clearanceCheck wiring harness
between sensor and
ABS ECUNormal
NormalMK-60 ABS system -ABS System Check5-105Fault code is 00283, 00285, 00290, 00287 3
[Description]When speed >20km/h, if sensor signal exceeds tolerance
range, this fault code will appear.
[Prompt ] It is propably because intermittent poor contact or short
circuit of sensor coil or wiring harness, gear ring is dam
aged or air gap between sensor and gear ring is too large, so
sensor signal is too weak.Possible cause

Intermittent poor contact or
short circuit of sensor coil or
wiring harness

Air gap between Sensor and
gear ring is too large or too small

Gear ring teeth is damaged

Bearing clearance is too large

ABS ECU fails
Abnormal
Abnormal
Abnormal Check the pulse ring

MK-60 ABS system -ABS System Check5-106Fault code is 00283, 00285, 00290, 00287 4
[Description]When identifiable open circuit, short circuit etc faults exist on
sensor, this fault code will appear.
[Prompt ] It might because poor contact of sensor, short circuit of coil or
wiring harness or faulty sensor signal processing circuit in ABS
ECUPossible cause

Sensor socket connector
or coil is disconnected

Sensor coil appear is
shorted

Sensor plug or wiring har-
ness is shorted with earth or
power supply

ABS ECU sensor signal
processing circuit failsCheck sensor of each wheel
Replace ABS ECURemove ABS ECU plug, check
whether resistance value between
the following terminals conforms
to standard value or not?
Standard value : 1.0-1.3K ohm¸
Left front : 45-46
Right front :33-34
Left rear : 36-37
Left rear: 42-43Check corresponding sensor
plugWhether fault recursCheck wiring harness between ECU and sensorRefer to key point for re-
pair of occasional fault Repair socket connector
Normal
No
YesAbnormal
AbnormalNormal Normal

MK-60 ABS system -ABS System Check5-107Fault code is 01044 5
[Description]When ECU software code is inconsistent with hardware
bouncing pin connection, this fault code will appearPossible cause

Bouncing pin connection
error in ABS wiring harness

Abs ecu coding error
Fault code is 00668 6
[Description]When supply terminal 30 does not supply voltage or
voltage is too high, this fault code will appear.Possible cause

Abs system fuse is blown out

Storage battery voltage is too
low or too high

ABS wiring harness socket
connector is damaged

ABS ECU is damaged
Check ABS system 30 A safety wireReplace fuse
NormalAbnormal
Disconnect connection of ABS wiring harness and ECU,
turn ignition switch to ON position, measure voltage value
between the following terminals of ABS wiring harness
Terminal 1 and 47 9.5 _ 16.5V
Terminal 32 and 16 9.5 - 16.5V
Terminal 4 and 16 9.5 _16.5VReplace fuse Normal
Check ABS wiring harness socket connectorReplace fuse Abnormal
Retry. Abnormity reoccursYes
Check storage battery voltageNormal Abnormal
NoRefer to repair of
occasional fault
Key pointsUse fault diagnosis instrument to check whether ABS ECU software
code is correct
Correct value: 040907Recode
YesNoCheck whether ABS wiring harness bouncing pin joint is connected
Bouncing pin joint : ABS ECU Pin 38and Pin 14Repair wiring harness Abnormal

MK-60 ABS system -ABS System Check5-108Fault code is 01130 7
[Description]When ABS suffers from high frequency interference of electro
magnetic wave or microprocessor thinks that input speed signal
is unauthentic, this fault code will appearPossible cause

High frequency interfer-
ence of electromagnetic
wave

Sensor is damaged or sen-
sor wiring harness is dam-
aged

ABS ECU is damagedCheck sensor output voltageReplace wheel
speed
Replace ABS ECUNoCheck sensorAbnormalCheck wiring harness
between ECU and
sensor Normal