tow GMC YUKON 2009 Get To Know Guide

Getting to Know Your Yukon/Yukon Denali2
See Section 3 of your Owner Manual.
Instrument Panel
DRIVER INFORMATION
ABCDFGHAA
IJKLMNOPQRSQ
The main features of the instrument
panel include:
A. Air Outlets
B. Turn Signal/Multifunction Lever
C. Instrument Panel Cluster
D. Shift Lever
E. Daytime Running Lamp Sensor
F. Tow/Haul Selector Button (if equipped)
G. Driver Information Center Controls
H. Audio System/Navigation System
(if equipped)
I. Exterior Lamps ControlJ. Dome Lamp Override Button/Fog
Lamp Switch/Instrument Panel
Brightness Knob
K. Automatic Transfer Case Control
L. Cruise Control Buttons/Heated
Steering Wheel Button (if equipped)
M. Tilt Steering Wheel Lever
N. Horn
O. Audio Steering Wheel Controls
P. Climate Controls
Q. Accessory Power Outlets
R. StabiliTrak Button (if equipped)
S. Glove Box
E

The accelerator
and brake
pedals can be
adjusted to a
comfortable and
safe operating
position by using
the switch located on the center console
below the climate controls.
Press the top arrow on the switch to
move the pedals away from you and
press the bottom arrow on the switch
to move the pedals toward you.
The pedals cannot be adjusted when the
vehicle is in Reverse or when cruise
control is activated.
See Section 2 of your Owner Manual.
Getting to Know Your Yukon/Yukon Denali8
Memory Settings (if equipped)
Adjustable Pedals (if equipped)
2nd-Row Seats
The heated rear seat controls are on the
rear control panel, located on the back
of the floor console.
(Heated Seat):Press the button
to turn on the heated seat and cycle
through the temperature settings.
See Section 1 of your Owner Manual.
Heated and Cooled Seats
(if equipped)
The following heated and cooled front
seat controls are located on the front
doors:
(Heated Seat):Press the bottom
button to turn on the heated seat.
(Cooled Seat):Press the top button
to turn on the cooled seat.
Continue to press the desired button to
cycle through the temperature settings
of High (three indicator lights), Medium
(two indicator lights), Low (one indicator
light), and Off (no indicator lights).
See Section 1 of your Owner Manual.
The memory buttons are located on
the driver’s door. Settings can be
programmed for the driver’s seat (the
lumbar setting is saved only on vehicles
equipped with cooled seats), outside
mirrors and the adjustable pedals
(if equipped) for two drivers.
To save memory settings:
1. Adjust the driver’s seat, outside
mirrors and pedals to a comfortable
position.2. Press and hold button 1 or 2 until two
beeps sound.
Repeat these steps for a second driver.
To recall the settings, press memory
button 1 or 2 with the vehicle in Park.
If the Remote Keyless Entry transmitter
is used to enter the vehicle and the
memory seat recall feature is on (see
Customization Features), the settings
will be recalled automatically.
Easy Exit Seat
The easy exit seat button is located
between the two memory buttons.
With the vehicle in Park, press the
(Easy Exit) button to move the driver’s
seat to the exit position.
If the easy exit seat feature is on (see
Customization Features), automatic seat
movement will occur when the key is
removed from the ignition.
See Section 1 of your Owner Manual.

Getting to Know Your Yukon/Yukon Denali18
Automatic Headlamp System
and Interior Lamps
Side Blind Zone Alert
(if equipped)
When a vehicle is detected in your blind
zone on either side of the vehicle, a
warning light will be displayed in the
corresponding outside mirror. If the turn
signal is activated while a vehicle is
detected, the warning light will flash. The
system is turned on each time the vehi-
cle is started. It can be turned off using
the DIC.
See Sections 2 and 3 of your Owner Manual.
Your vehicle is equipped with an
Automatic Headlamp System, which
turns on the Daytime Running Lamps
(DRLs) during the day and the head-
lamps and other exterior lamps at night
or when necessary.
The system uses a light sensor, located
on top of the instrument panel, to deter-
mine light conditions. For proper system
operation, avoid placing any objects on
or near the sensor.
The exterior and interior lamp controls
are located on the instrument panel to
the left of the steering wheel.
Exterior Lamp Controls
(Off/On):When operating in the
AUTO position, turn the knob to this
The cruise
control buttons
are located on
the steering
wheel.
(On/Off):
Press this but-
ton to turn the
cruise control
system on
or off.
– SET (Set):Press this button to set a
speed, or to decrease the speed if the
system is set. When the cruise control
speed is set, the cruise light will illumi-
nate in the instrument cluster.
+ RES (Resume):Press this button to
resume a set speed, or to increase the
speed if the system is set.
(Cancel): Press this button to can-
cel the cruise control but retain the set
speed in memory.
See Section 3 of your Owner Manual.
Auto Turn Signal
Cruise Control (if equipped)
The turn signal lever includes an auto-
matic lane change signal feature.
To signal a lane change, raise or lower
the lever until the arrow on the instru-
ment panel cluster starts to flash, and
then release the lever. The turn signal
will automatically flash three times. If the
Tow/Haul mode is selected, the turn sig-
nal will automatically flash six times.
To signal a turn, move the lever all the
way up or down.
See Section 3 of your Owner Manual.

Getting to Know Your Yukon/Yukon Denali24
15911401 A
Roadside Assistance
My GMLink
The GMC Owner Center at My GMLink
is a complimentary service for GMC
owners, a one-stop resource to enhance
your GMC ownership experience.
Exclusive member benefits include
online service reminders, vehicle main-
tenance tips, online owner manual,
special privileges and more. Sign up
today at www.mygmlink.com.
Certain restrictions, precautions and safety procedures apply to your vehicle. Please read your Owner
Manual for complete instructions. All information contained herein is based on information available at the
time of printing and is subject to change without notice. Copyright 2008 by GM Corp. All rights reserved.
!15911401=A!
1-800-GMC-8782
(1-800-462-8782)
TTY Users: 1-888-889-2438
As the proud owner of a new GMC
vehicle, you are automatically enrolled in
the GMC Roadside Assistance program.
This value-added service is intended to
provide you with peace of mind as you
drive in the city or travel the open road.
GMC’s Roadside Assistance toll-free
number is staffed by a team of technically
trained advisors, who are available
24 hours a day, 365 days a year. The
advisors can provide minor repair infor-
mation or make arrangements to tow
your vehicle to the nearest GMC dealer.
GMC will provide the following services
for 5 years/100,000 miles at no expense
to you:
• Fuel delivery
• Lockout service (identification
required)
• Tow to nearest dealership for warranty
service
• Flat tire assistance
• Jump starts
In many instances, mechanical failures
are covered under GMC’s comprehensive
warranty. However, when other services
are utilized, our advisors will explain any
payment obligations you might incur.
OWNER INFORMATIONFor prompt and efficient assistance when
calling, please provide the following infor-
mation to the advisor:
• Location of the vehicle
• Telephone number and your location
• Vehicle model, year and color
• Vehicle mileage
• Vehicle Identification Number (VIN)
• Vehicle license plate number
GMC reserves the right to limit services
or reimbursement to an owner or driver
when, in GMC’s judgment, the claims
become excessive in frequency or type
of occurrence.
Roadside Assistance and OnStar
®
(if equipped)
If you have a current OnStar subscrip-
tion, press the OnStar button and the
vehicle will send your current GPS
location to an OnStar Advisor who will
speak to you, assess your problem,
contact Roadside Assistance and relay
your exact location
so you will get the
help you need.