door lock GREAT WALL FLORID 2008 Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 233Vehicle Body
Front Door Lock Assembly ...............................................234
Rear Door Lock Assembly ................................................237
Trunk Door Lock Assembly ...............................................239
Wiper Arm and Vent Panel Assembly ...............................240
Front & Rear Window Glasses .........................................241
Dashboard ........................................................................\
242
Cooling Unit ......................................................................246
Front Door Assembly ........................................................248
Rear Door Assembly.........................................................251
Trunk Door Assembly .......................................................254
Front Bumper....................................................................256
Rear Bumper ....................................................................259
Seat Belt ........................................................................\
...262
Seats ........................................................................\
........266
Sunroof Assembly.............................................................268
Vehicle Body

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual234
Front Door Lock Assembly
Components
Front door lock installation and removal
1. Install the outside handle framework.
Install the door lock tie rod on the outside handle's framework,
install the outside handle framework, and tighten
the mounting screw.
2. Install the gasket.
3. Install the outside handle of the front door on the out-
side handle framework.
Inside handle assembly
Front door lock assembly LH
Lock mounting screw
Gasket
Front door locking cable installing buckle
Front door unlock cableFront door lock cable
Front door lock latchFront door lock cylinder assembly LH
Lock cylinder decorative cap
Front door outside handle
Gasket
Front door outside handle framework
Front door tie rod assembly
Q2580820 + Q141F32
Framework mounting screw
Door lock tie rod
Front door outside handle
Gasket mounting hole

Downloaded from www.Manualslib.com manuals search engine 235Vehicle Body

4. Separate installation for the front door lock assembly.
Separately install the front door lock, lock cable, unlock
cable, cable installing buckle, and side door inside handle
assembly. On the left is the schematic diagram after installa-
tion.
7. Install the inside handle.
Clamp the inside handle clip to the door inner decoration
board, and then firmly press the inside handle clip dowel pin
into the mounting hole.
8. Install the front door lock cylinder.
Clip the decorative cap of the driver side door onto the lock
cylinder, install the lock cylinder into the lock hole, and then
tighten the lock cylinder’s mounting screw.
5. Install the front door lock assembly.
Install the assembled assembly, tighten the lock mounting
screws (pay attention to put the outwardly opened tie rod in
and block the lock's outwardly opened swing arm lever clip
sheath), and insert the wire harness plug-in into door lock
socket.
6. Install the cable buckle.
Install the buckle in the door inner decoration board, and put
the cable in the buckle.
9. Install the door lock inside handle screws.
When the door cylinder panel assembly is installed, tighten
the inside handle's mounting screw.
Door lock socket
Inside handle dowel pinInside handle clip
Lock cylinder decorative cap
Lock cylinderMounting screw
Mounting screw
Door lock inside handle

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual236
10. Install the door lock latch.
11. Front door lock removal.
For the removal, please simply reverse the installation steps.
Caution: The front door tie rod can be removed following
the outside handle framework. The front door tie rod
can be removed after the removal of the outside handle
framework.
Door lock latch
Q2580820 + Q141F32

Downloaded from www.Manualslib.com manuals search engine 237Vehicle Body
Rear door lock installation and removal
1. Install the outside handle framework, and tighten the
framework mounting screw.
Rear Door Lock Assembly
Components
2. Install the gasket.
P u t t h e g a s k e t o n t o t h e m o u n t i n g h o l e ( s i m i l a r t o t h e
installation for the front door).
3. Install the rear door outside handle on the outside han-
dle framework.
4. Separate installation for the rear door lock assembly.
Separately install the rear door lock, lock cable, unlock
cable, cable installing buckle, and rear door inside handle as-
sembly (similar to the installation for the front door).
Rear door outside handle
Rear door lock latch
Rear door lock cable installing buckle
Rear door lock assembly LH
Lock mounting screw
Rear door inside handle assembly LH
Rear door handle decorative cap
Rear door outside handle framework LH
Rear door outside handle gasket
Rear door outside handle gasket 2
Q2580816
Framework mounting screw
Gasket
Rear door outside handle

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual238
5. Install the rear door lock assembly.
Install the assembled assembly, tighten the lock mounting
screws (pay attention to put the outwardly open swing arm
lever clip of the lock onto the outer opened fork of the out-
side handle framework), and then insert the wire harness
plug-in into the door lock socket.
6. Install the cable buckle.
7. Install the inside handle.
Clamp the inside handle clip to the door inner decoration
board, and then firmly press the inside handle clip dowel pin
into the mounting hole.
8. Install the rear door outside handle decorative cap, and
tighten the decorative cap mounting bolt.
9. Install the inside handle screw.
When the door cylinder panel assembly is installed, tighten
the inside handle's mounting screw.
10. Install the rear door lock latch.
11. For rear door lock removal, please simply reverse the
installation steps.
Door lock fork
Inside handle dowel pin
Inside handle clip
Mounting screw
Door lock inside handle
Rear door lock latch
Q2580822

Downloaded from www.Manualslib.com manuals search engine 239Vehicle Body
Trunk door lock installation and removal
1. Install the trunk door outside handle.
Install the trunk door outside handle assembly, tighten the
mounting screw, and install the wire harness plug-in.
Trunk Door Lock Assembly
Components
2. Install the trunk door main lock assembly.
Install the trunk door main lock assembly, and tighten the
mounting screw.
3. Install the trunk lock latch.
4. For trunk lock removal, please simply reverse the
installation steps.
Trunk door lock assembly
Q1460620 (Q402) F3
Trunk door lock latch
Q2580820 + Q141F32
Q1840616F3
Trunk door outside handle assemblyConnect the central door lock controller
Connect the door lamp indicator
Q1460620 (Q402) F3
Connect the door lamp indicator
Connect the central door lock controller
Q1840616F3

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual248
Front door removal
1. Remove the front door inner decoration board.
(a) Remove the interior armrest screw and armrest.
(b) R e m o v e t h e d o o r i n s i d e h a n d l e s c r e w a n d i n s i d e
handle.
(c) Remove the electrical switch and pull out the wire
harness.
(d) Insert buckle screwdriver between the fixed buckle and
the door inner decoration board to pry them loose.
Caution: Before using a buckle screwdriver, make sure
to wrap its head in tape.
(e) Take down the door inner decoration board.
Front Door Assembly
Components
Front door triangular protector LH
Front door protector assembly LH
Front door armrest LH
Front door internal weatherstrip LH
Front door assembly LH
Front door lower hinge assembly LH
Front door retainer LH
Front door upper hinge assembly LH
Left external rearview mirror assembly
Front door window front guide rail assembly LH
Front door glass run LH
Front door window LH
Front door weatherstrip LH
Front door external weatherstrip LH
Front door lock assembly LH
Window regulator assembly
Front door window rear guide rail assembly LH
Front door armrest LH
Front door window
switch assembly LH
Front door protector LH

Downloaded from www.Manualslib.com manuals search engine 249Vehicle Body
2. Remove the front door external weatherstrip.
Lower the window and manually grasp the weatherstrip
firmly, then pull it up to remove.
3. Remove the front door window assembly.
(a) A d j u s t t h e w i n d o w t o m a k e t h e w i n d o w b r a c k e t
mounting bolts level with door inner decoration board
mounting hole, and remove the two window bracket
mounting bolts.
(b) Pull the window upwards and then tilt it to remove.
4. Remove the front door glass run.
5. Remove the front door window guide rail assembly.
6. Remove the window regulator.
(a) Remove the six mounting bolts from the regulator
bracket.
(b) Remove the regulator via the auxiliary hole.
7. Remove the vehicle inner lock button.
8. Front door window assembly replacement.
(a) Adjust the front door window to make the window
bracket mounting bolts level with door inner decora-
tion board mounting hole.
(b) Remove the window bracket's mounting bolts to take
the glass out for replacement.
Front door installation
1. Coat grease.
Coat MP grease on the components before installing them.
(a) Coat MP grease to sliding surfaces and the gears of the
window regulator.
Caution: Do not coat MP grease to the spring of the
window regulator.
(b) Coat MP grease to the sliding surface of the door lock.
2. Install the door outside handle with lock cylinder and
door lock.
(a) Install the lock cylinder on the door outside handle with
spring clasp.
(b) Install the door outside handle and lock cylinder with
two bolts with spring clasp.
(c) Install the door lock with three bolts.
(d) Connect the control lever to the door outside handle.
3. Install the door inner lock button.
Install the door inner lock button and connect the control
lever.
Front door glass run LHFront door window LH
Front door assembly LH
Front door window front guide rail LH
Front door window rear guide rail LH
Front door external weatherstrip LH
Front door lower hinge LH
Front door upper hinge LH
Window regulator assembly
Front door lock assembly LH
Front door assembly LH
Front door assembly LH
Front door window LH
Front door outside handle LH
Window regulator assembly
Front door lock assembly LH
Front door outside handle LH
Front door inside handle LH

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual252
2. Remove the rear door external weatherstrip.
Lower the window and manually grasp the weatherstrip
firmly, then pull it up to remove.
3. Remove the rear door window assembly.
(a) Pull the rear door regulator down in a position that en-
ables the rocker to turn freely, and then lower the win-
dow. Finally make the rocker slide out of the guide rail
below the window.
(b) Pull the window upwards and then tilt it to remove.
4. Remove the rear door glass run.
5. Remove the rear door window guide rail assembly.
6. Remove the window regulator.
(a) Remove the four mounting bolts of the regulator
bracket.
(b) Remove the regulator via the auxiliary hole.
7. Remove the vehicle inner lock button.
8. Rear door window assembly replacement.
(a) Adjust the rear door window to make the window
b r a c k e t m o u n t i n g b o l t s l e v e l w i t h t h e d o o r i n n e r
decoration board mounting hole.
(b) Remove the window bracket mounting bolts to take the
window out for replacement.
Rear door installation
1. Coat grease.
Coat MP grease on the components before installing them.
(a) Coat MP grease to sliding surfaces and the gears of
window regulator.
Caution: Do not coat MP grease to the spring of the
window regulator.
(b) Coat MP grease to the sliding surface of the door lock.
4. Install the window regulator.
(a) Install the regulator via the auxiliary hole.
(b) Install the four regulator's mounting bolts.
2. Install the door outside handle with lock cylinder and
door lock.
(a) Install the lock cylinder on the door outside handle with
spring clasp.
(b) Install the door outside handle and lock cylinder with
two bolts.
(c) Install the door lock with three bolts.
(d) Connect the control lever to the door outside handle.
3. Install the door inner lock button and connect the con-
trol lever.
Rear door window rear guide rail LH
Rear door glass run LHRear door window LH
Rear door external weatherstrip LH
Rear door window front guide rail LH
Rear door window regulator LH
Rear door window regulator LH
Rear door assembly LH
Rear door outside handle assembly LH
Rear door window regulator LH
Rear door lock assembly LH
Rear door assembly LH
Rear door outside handle assembly LH
Rear door window regulator LH
Rear door assembly LH
Rear door outside handle assembly LH
Rear door assembly LH
Rear door lock assembly LH