clock HONDA ACCORD HYBRID 2005 CL7 / 7.G Owners Manual

Each f ront door has a master door
lock switch. Either switch locks and
unlocks all doors. Push the top of the
switch to lock all doors; push the
bottom to unlock them.
To lock any passenger’s door when
getting out of the vehicle, push the
lock tab down, and close the door.Only the driver’s door has a door
lock.
Insert your key into the door lock
and turn it counterclockwise once to
lock the driver’s door and the other
doors.
Insert your key into the door lock
and turn it clockwise once to unlock
the driver’s door. Turn the key back
and turn it clockwise again to unlock
the other doors.
With the driver’s door open and the
key in the ignition, both door lock
switches are disabled. They are not
disabled if the driver’s door is closed.
Pushing the switch down on the
open passenger’s door will lock all
doors.
L ockout Prevent ion
Door L ocks
80
MASTER DOOR LOCK SWITCH
top
bottom
 — 
— y

 y
('  y  y

The power window system has a key-
of f delay f unction. The windows will
stilloperateforupto10minutes
after you turn off the ignition switch.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch to ON (II) again
bef ore you can raise or lower the
windows.You can open and close the windows
with the key in the driver’s door lock.
To open:Insert the key in the driver’s door
lock.
Turn the key clockwise, then
release it.
You can open all of the windows
from the outside with the remote
transmitter.
Press the UNLOCK button once
to unlock the driver’s door.
Press the UNLOCK button a
second time, and hold it. The
passenger’s doors unlock, and all
f our windows start to open. To
stop the windows, release the
button.
To open the windows f urther,
press the button again.
You cannot close the windows with
the remote transmitter. 1.
2.
3.
1.
2.
Opening/Closing t he Windows wit hthe Key
Opening t he Windows wit h t he
Remote Transmitter
Power Windows
92
UNLOCK BUTTON
Open
Close
 — 
— y
 y
('  y  y

Turnthekeyclockwiseagain,and
hold it. All f our windows start to
open. To stop the windows,
release the key.
To open the windows f urther, turn
andholdthekeyagain.
To close: Insert the key in the driver’s door
lock.
Turn the key counterclockwise,
then release it.
Turn the key counterclockwise
again, and hold it. All four
windowsstarttoclose.Tostopthe
windows, release the key.
To close the windows f urther, turn
andholdthekeyagain. To apply the parking brake, pull the
lever up f ully. To release it, pull up
slightly, push the button, and lower
the lever. The parking brake light on
the instrument panel should go out
when the parking brake is f ully
released with the engine running
(see page ). If you drive without f ully releasing
the parking brake, the beeper
sounds continuously.
1.
2.
3.
4. 3.
4.
54
Parking Brake
Power Windows, Parking Brake
Inst rument s and Cont rols
93
PARKING BRAKE LEVER
Driving the vehicle with the parking
brake applied can damage the rear
brakes and hubs.
 — 
— y
 y
('  y  y

Your heating and air conditioning
system provides a comf ortable
environment in all weather
conditions.
Your audio system has many
f eatures. This section describes
them.
The security system helps prevent
your vehicle f rom being broken into
or being stolen..............
Vents, Heating, and A/C . 100
..........
Dual Temperature Control . 109
..............
Climate Control Sensors . 111
..........................
Playing the Radio .112
.....................
To Play the Radio .113
....................
To Select a Station . 113
.................
Adjusting the Sound . 116
....................
Radio Frequencies . 117
........................
Radio Reception .117
..................................
Playing a CD .119
..........
Playing a CD, CD Changer . 120
.............................
To Play a CD .120
...............
To Stop Playing a CD . 123
Removing CDs from the .................................
Changer .123
Operating the Optional CD .................................
Changer .124
.........
CD Player Error Messages . 125
.....
CD Changer Error Messages . 126
.....................
Protecting your CDs .127
.................
General Inf ormation . 127
..........................
Protecting CDs .127
...............................
Playing a Tape .128
..........................
To Play a Tape .129
............
To Stop Playing a Tape . 129
............
Tape Search Functions . 130 .....
Caring the Tape and Player . 131
Playing the XM Satellite ......................................
Radio .132
...............
Satellite Digital Radio . 132
...
To Play XM Satellite Radio . 133
..................
To Select a Channel . 133
..............
Satellite Radio Signals . 135
Receiving Satellite Radio ....................................
Service .136
.............
Steering Wheel Controls . 138
.................
Radio Thef t Protection . 139
..........................
Setting the Clock .140
............................
Security System .141
...............................
Cruise Control .142
HomeLink Universal ................................
Transceiver .145
Features
Features
99
TM
TM
 —
 — 
y  
y
('  y 
 y

µµµ
The
seek/skip f unction selects the
various categories in XM, such as
Jazz/Blues, Rock, Classical, etc.
Push the to change the
category f orward. Push the to
change the category backward. To
search f or channels within a
category, turn the TUNE knob
clockwiseorpresstheTUNEbar . The scan f unction samples
all channels f or 5 seconds. To
activate the f unction, push the SCAN
button. Push it again to get out of the
sequence.
Each preset icon or button
canstoreonechannelinXM1and
one in XM2.
Use the TUNE, SEEK or SCAN
function to tune the radio to a
desired channel.
Pick a preset icon or button and
hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on XM1 and XM2. Once your XM channels are preset,
pressing the CH DISC button will
select your preset channels.
Push the CD/AUX XM button.
(You will see XM1 or XM2.)
1.
2.
3.
4.With Navigation SystemSEEK /SK IP (CA T EGORY) SCA N
Preset
Playing the XM Satellite Radio
134
TM
 —
 — 
yy
('  y 
y

If your vehicle’s battery is
disconnected or goes dead, you will
need to set the clock.You can quickly set the time to the
nearest hour. Pressing and holding
the SOUND button, then pressing
theR(Preset6)sideof thebarsets
the clock back to the previous hour.
If the displayed time is after the half
hour, the clock sets the clock
f orward to the beginning of the next
hour.For example:
1:06 would RESET to 1:00.
1:52 would RESET to 2:00.
Ref er to the Navigation System
Owner’s Manual to set up the time.
Press and hold the SOUND button
until you hear a beep. The displayed
time begins to blink. Press on the H
(Preset 4) side of the bar until the
numbers advance to the desired time.
Change the minutes by pressing the
M (Preset 5) side of the bar until the
numbers advance to the desired time.
When you are f inished, press the
SOUND button again to set the time.
Without Navigation System
With Navigation System
Setting the Clock
140
DIGITAL CLOCKSOUND BUTTON PRESET BARS
Without Navigation System shown
 —
 — 
yy
('  y 
y

Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.
The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill. Clean
up any spill immediately; it could
damage components in the engine
compartment.
Put the radiator cap back on and
tighten it.
Make sure the engine and radiator
are cool.
Relieve any pressure in the cooling
system by turning the radiator cap
counterclockwise, without
pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise. 4.
1.
2.
3. 5.
6.
Engine Coolant
Maint enance
207
RADIATOR CAP
 —
 — 
yy
('  y 
 y

Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Install the new bulb and turn it
one-quarter turn clockwise to lock
it in place.Push the electrical connector onto
the bulb.
Turn on the headlights to test the
new bulb.
Open the hood. To change a bulb
on the driver’s side, undo the two
f asteners and remove the air
intake cover. Reinstall the air intake cover.
Reinstall the two fasteners and
secure them by pushing on the
heads until they lock.
1. 3.
2. 4.5.
6.
7.
High Beam Headlight
Lights
Maint enance
211
AIR INTAKE
COVER
FASTENERS TABBULB
 —
 — 
y y
('  y 
y

To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.
Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Install the new bulb and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector onto
the bulb.
Turn on the headlights to test the
new bulb.
Put the inner f ender cover in place.
Install the two holding clips. Lock
each one in place by pushing on
the center.
3.
4.
5.
1.
2. 6.
7.
8.
9.
L ow Beam Headlight
Lights
212
HOLDING CLIPS
BULB
 —
 — 
y
y
('  y 
y

To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.
Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.To remove the burned out bulb,
push it in and turn it
counterclockwise until it unlocks.
Install the new bulb and turn it
clockwise to lock it in place.
Insert the socket into the
headlight assembly. Turn it
clockwise to lock it in place.
Test the new bulb to make sure it
works.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.
Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
1. 3.
2. 4.
8. 7. 6.
9. 5.
Replacing the Front Side Marker/
Turn Signal and Parking L ight
Bulb
Lights
Maint enance
213
HOLDING CLIPS
BULB
 —
 — 
y y
('  y 
y