HONDA ACCORD SEDAN 2006 (in English) Repair Manual

The appropriate indicator comes on
in this monitor if the trunk or either
door is not closed tightly.
All the indicato rs in the monitor
come on for a few seconds when you
turn the ignition switch to ON (II).
This
indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position. This
indicator normally comes on for
a few seconds when you turn the
ignition switch to ON (II). For more
info rmation, see page .
This indicator has three functions:
Itcomesonasareminderthatyou
have turned off the vehicle
stability assist (VSA) system.
It flashes when VSA is active (see
page ).
It comes on along with the VSA
system indicator if there is a
problem with the VSA system.
Ifitcomesonandstaysonatany
other
time, or if it does not come on
wh en you turn the ignition switch to
ON (II), there is a problem with the
VSA system. Take your vehicle to a
dealer to have it checked. Without
VSA, your vehicle still has normal
driving ability, but will not have VSA
traction and stability enhancement.
See page for more information
on the VSA system. 2.
3. 1.182
182
182 Door and T runk Open Monitor
Vehicle Stability Assist
(VSA ) System Indicator VSA A ctivation Indicator
Instrument Panel Indicators
60
——y
y
(yy

The left or right turn signal indicator
blinks when you signal a lane change
or turn. If the indicato rs do not blink,
or if they blink rapidly, it usu ally
means one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
WhenyouturnontheHazard
Warning button, both turn signal
indicators blink. All turn signals on
the outside of the vehicle should
flash. This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. If you turn the
ignition switch to the ACCESSORY
(I) or the LOCK (0) position without
turning of f the light switch, this
indicator will remain on. A reminder
chime will also sound when you open
the driver’s door.
This indicator is located in the f uel
gauge. It comes on as a reminder
that you must ref uel soon.
When the indicator comes on, there
are about 2.72 U.S. gal (10.3
)of
f uel remaining in the tank bef ore the
needle reaches E. There is a small
reserve of f uel remaining in the tank
when the needle does reach E.
221 222
Turn Signal and
Hazard Warning
Indicators
Lights On Indicator Low Fuel Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
61
LOW FUEL INDICATOR
——y

y
(yy

This indicator comes on with the
high beam headlights. For more
info rmation, see page .
This indicator comes on when the
security system is set. See page
f or more inf ormation on the
security system. When the daytime running lights
(DRL) are on, this indicator comes
on with reduced brightness.
If this indicator comes on when the
ignition switch is turned to the ON
(II) position and the parking brake is
released, it means there is a problem
in the high beam headlight’s circuit.
Have your vehicle checked by your
dealer.
144 70
U.S. EX, EX-L, LX-V6 and EX-V6
Canadian SE, EX-L, SE-V6 and EX-V6
Security System Indicator ‘‘Daytime Running
Lights’’ Indicator High Beam Indicator
Instrument Panel Indicators
62
SECURITY SYSTEM INDICATOR
——y
y
(yy

This indicator comes on for a few
seconds when you turn the ignition
switch to the ON (II) position. It will
gooffifyouhaveinserteda
properly-coded ignition key. If it is
not a properly-coded key, the
indicator will blink and the engine
will not start (see page ).
This indicator also blinks several
times when you turn the ignition
switch from the ON (II) position to
the ACCESSORY (I) or the LOCK
(0) position.
This
indicator comes on when you
turn on the cruise control master
button (see page ).
This indicator comes on when you
set the cruise control. See page
for information on operating the
cruise control.
This indicator comes on when the
washer fluid level is low. Add washer
fluidwhenyouseethisindicator
come on (see page ).
This
indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance. The
maintenance main items and sub
items will be displayed in the
information display. See page for
more inf ormation on the
maintenance minder.
This indicator goes of f when your
dealer resets it after completing the
required maintenance service.
145
145 193
75
208Only on models equipped with Cruise Control System
Only on models equipped with CruiseControl System
Canadian models only
Immobilizer System
Indicator
Cruise Control Main
Indicator Maintenance Minder
Indicator
Cruise Control Indicator
Washer Level Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
63
——
y

y
(yy

The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
federal law and Canadian provincial
regulations to disconnect, reset, or
alter the odometer with the intent to
change the number of miles or
kilometers indicated.The temperature sensor is in the
f ront bumper. Theref ore, the
temperature reading can be af f ected
by heat ref lection f rom the road
surf ace, engine heat, and the
exhaust f rom surrounding traf f ic.
This can cause an incorrect
temperature reading when your
speed is under 19 mph (30 km/h).
The sensor delays the display update
until it reaches the correct outside
temperature. This may take several
minutes.
The odometer and the outside
temperature display use the same
display. To switch the display
between the odometer and the
outside temperature, press the
Select/Reset knob. When you turn
the ignition switch to ON (II), what
you last selected is displayed. This display shows the outside
temperature in Fahrenheit (U.S.
models) or Centigrade (Canadian
models). To see the outside
temperature, press and release the
Select/Reset knob until the
temperature is displayed.
EX-L and EX-V6
Odometer
Odometer/Outside T emperature
Display Outside Temperature Display
Gauges
64
TACHOMETER
SPEEDOMETER
FUEL GAUGE
TEMPERATURE
GAUGE
TRIP METER
ODOMETER/OUTSIDE
TEMPERATURE INDICATOR
SELECT/RESET KNOB
U.S. model shown
——yy
(yy

¶¶µµµµ
µµµµ This
meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between these
displays and the odometer/outside
temperature display by pressing the
Select/Reset knob repeatedly. Each
trip meter works independently, so
you can keep track of two different
distances. This
shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise into the
upperhalfofthegauge.Ifitreaches
the red (Hot) mark, pull safely to the
side of the road. Turn to page for
instru ctions and precautions on
checking the engine’s cooling
system.
If the outside temperature is
incorrectly displayed, you can adjust
it up to 5°F ( 3°C) warmer or
cooler.
NOTE: The temperature must be
stabilized bef ore doing this
procedure.
Select the outside temperature
display, then press the Select/Reset
knob f or 10 seconds. The f ollowing
sequences appear, 1 second at a
time:0,1,2,3,4,5, 5, 4, 3, 2,
1, 0, 1 (0, 1, 2, 3, 3, 2, 1, 0, 1).
When the temperature reaches the
desired value, release the Select/
Reset knob. You should see the new
outside temperature displayed.
In certain weather conditions,
temperature readings near f reezing
(32°F, 0°C) could mean that ice is
f orming on the road surf ace. When you turn the ignition switch to
ON (II), what you last selected is
displayed.
To reset a trip meter, display it, and
then press and hold the Select/Reset
knob until the number resets to ‘‘0.0’’.
248
Trip Meter
Temperature Gauge
Gauges
Inst rument s and Cont rols
65
——yy
(yy

This shows how much fuel you have.
It may show slightly more or less
th an the actual amount. The needle
returns to the bottom after you turn
off the ignition. If
your fuel cap is loose or missing, a
‘‘CHECK FUEL CAP’’ message will
appear in the odometer/outside
temperature display. As soon as it is
safely possible, turn the engine off
and check that the fuel cap is
installed. If it is, loosen the cap and
tighten it 1 click. Although you can
use the Select/Reset button to cycle the fuel cap warning off of the display, it will be displayed again each time the engine is started. It
will take several da ys of normal
driving for the vehicle to turn the
warning off.
If the vehicle on board diagnostic
system continues to detect a
problem, the Mal function Indicator
Lamp (MIL) will illuminate. If the
MIL does not go off, have your
de aler inspect the vehicle. For more
info rmation, see page . The
information display in the
instrument panel shows you the
engine oil life and maintenance
service items when the ignition
switch is in the ON (II) position. This
information helps to keep you aware
of the periodic maintenance your
vehicle needs for continued trouble-
f ree driving. Ref er to page f or
more information. 193
251
Fuel Gauge
Check Fuel Cap Indicator
(odometer/outside temperature
message) Maintenance Minder Display
Gauges
66
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
——
y
y
(yy

Î
Î Only on vehicles equipped with navigation system. Refer to the navigation system manual.
:
Controls Near the Steering Wheel
Instru m ent sand Cont ro ls
67
WINDSHIELD
WIPERS/WASHERS
INSTRUMENT
PANEL
BRIGHTNESS
MOONROOF
SWITCH
HEADLIGHTS/
TURN
SIGNALS
REMOTE AUDIO
CONTROLS
HORN
STEERING WHEEL
ADJUSTMENT CRUISE
CONTROLS
REAR WINDOW
DEFOGGER PASSENGER AIRBAG
OFF INDICATOR
(P.31)
HAZARD
WARNING BUTTON
(P.71)
(P.69)
(P.141)
VOICE CONTROL
SWITCHES
(P.94)
(P.181) (P.73)(P.68)
(P.71)
(P.145)
(P.72, 108)
VSA OFF SWITCH
——y
y
(yy

µ
µ
µ µ
µ µ
µ µ
µ
MIST
OFF
INT Intermittent
LO Low speed
HI High speed
Windshield washers Push the right lever up or down to
select a position.
The wipers run at high
speed until you release the lever.
The wipers are not activated. The wipers run at low speed.
The wipers run at high speed. Pull the
wiper control lever toward you, and
hold it. The washers spray until you
release the lever. The wipers run at
low speed, then complete one more
sweep after you release the lever.
The length of the wiper
interval is varied automatically
according to the vehicle’s speed.
Vary the delay by turning the INT
TIME ring. If you turn it to the
shortest delay, the wipers will
change to low speed operation when
the vehicle speed exceeds 12 mph
(20 km/h).
1.
2.
3.
4.
5.
6.
Except U.S. VP
Windshield Wiper
MIST
OFFLO
HI
Windshield Washer
INT
Wipers and Washers
68
——yy
(y
y

µ
µ µ
Tu
rn signal
Off
Parking and interior lights
Headlight on
High beams
Flashhighbeams Push
down on the
left lever to signal a left turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a tu rn.
Turning the switch
on the left lever to the position
turns on the parking lights, taillights,
side marker lights, rear license plate
lights and lights-on indicator.
Turning the switch to the
position turns on the
headlights. If you leave the lights on
with the ignition switch in
ACCESSORY (I) or LOCK (0), you
will hear a reminder chime when you
open the driver’s door.
When the light switch is in either of
these positions, the lights-on
indicator comes on as a reminder. To turn on the high
beams, push the lever f orward until
you hear a click. The blue high beam
indicator will come on (see page ).
To turn of f the high beams, pull the
lever back. To flash the high beams,
pull the lever f arther back, and then
release it. The high beams remain on
until the lever is released.
1.
2.
3.
4.
5.
6. 62
Turn Signal and Headlights Turn Signal
HeadlightsHigh Beams
Turn Signal, Headlights
Inst rument s and Cont rols
69
——y
y
(yy