power HONDA CIVIC 2002 7.G Workshop Manual

11.
12.
14.
Disconnect SRS unit connector B (18P) from the
SRS unit (see step 7 on page 23-22).
Disconnect the special tool from the floor wire
harness.
Reconnect the battery negative cable.
Turn the ignition switch ON (ll).
Check for voltage between the No. 1 lerminal of
SRS unit connector B {18P) and body ground, and
the No. 10 terminal and body ground. There should
be 0.5 V or less.
SRS UNIT CONNECTOR B I18PI
ls the voltage as specitied?
YES Faulty SRS unit; replace the SRS unit (see
page 23-1221 .f
NO Short to power in the floor wire harness;
replace the floor wire harness.l
I
fJ
4.
DTC 21-5: Short to Ground in Driver's Seat
Belt Buckle Tensioner
Special Tools Required. SRS inflator simulator 07SAZ-TB4011A. SRS simulator lead F 07XAZ-S230100
1. Erase the DTC memory {see page 23-26}.
2. Turn the ignition switch ON (ll), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SBS indicator stay on?
YES-Go to step 3.
NO Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-26).
Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Disconnect the driver's seat belt buckle tensioner
4P connector {A) from the floor wire harness.
Connect the SRS inflator simulator (2 Q
connectors) and simulator lead F to the floor wire
n a rness.
Reconnect the battery negative cable.
Erase the DTC memory.
(cont'd)
6.
7.
23-57

I
]
16. Disconnectthe driver's airbag connector (see step2 on page 23-211, front passenger's airbagconnector (see step 3 on page 23-21), and driver,sseat belt tensioner connector (see step 5 on page
23-221.
17. Disconnect SRS unit connector A (18p) from the
SRS unit (see step 7 on page 23-22).
18. Disconnect the special tool from dashboard wireharness B.
19. Check resistance between the No. 9 terminal andthe No. 18 terminal of SRS unit connector A (18p).
There should be an open circuit, or at least 1 Me.
SRS UNIT CONNECTOR A I18P}
Wire side of female terminals
ls the resistance as specified?
YES-Faulty SRS unit; replace the SRS unit (see
page 23-1221 .f
NO-Short in dashboard wire harness B; replace
dashboard wire harness B. I
RED/YEL
I]
t6r8 l \P
T
234568
10tl12t3151617
RED/BLK
DTC 4-4: Short to Power in Front Passenger's
Seat Belt Tensioner
Special Tools Required. SRS inflator simulator 07SAZ-T84011A. SRS simulator lead C 07TAZ-S25011A. SRS simulator lead F 07XAZ-S230100
1. Erase the DTC memory (see page 23-26).
2. Turn the ignition switch ON {ll), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicator stay on?
YES Go to step 3.
NO- Intermiftent failure. system is OK at this time.Go to Troubleshooting Intermittent Failures (see
page 23-261.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnectthe front passenger's seat belttensioner 2P connector (A) from the floor wire
harness.
07TAZ-S2501'lA
5. Connect the SRS inflator simulator (2 e connector)and simulator lead C to the floor wire harness.
{cont'd)
23-61

sRs
DTC Troubleshooting (cont'd)
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
ls DTC 4-4 indicated?
YES Go to step 9.
NO-Short to power in the front passenger's seat
belt tensioner; replace the front passenger's seat
belt (see page 23-4).I
9. Turn the ignition switch OFF. Disconnect the
battery negative cable. and wait for 3 minutes.
'10. Disconnect floor wire harness 4P connector
C403 (A)from dashboard wire harness B.
07sAz-TB4o11A
Connect the SRS inflator simulator (2 0
connectors) and simulator lead F to dashboard wire
harness B.
Reconnect the battery negative cable.
Erase the DTC memory.
Read the DTC.
ls DTC 4-4 indicated?
YES-Go to step 15.
NO- Short to power in the floor wire harness;
replace the floor wire harness.l
11.
tJ.
14.
23-62
11.
15.
to.
18.
19.
20.
21.
Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Disconnect the driver's airbag connector (see step
2 on page 23-211, tront passenger's airbag
connector (see step 3 on page 23-21), and drivefs
seat belt tensioner connector (see step 5 on page
23-22t.
Disconnect SRS unit connector A ('l8P) trom the
SRS unit (see step 7 on page 23-22).
Disconnect the special tool from dashboard wire
harness B.
Reconnect the battery negative cable.
Turn the ignition switch ON (ll).
Check for voltage between the No. 9 terminal of
SRS unit connector A (18P) and body ground, and
the No. 18 terminal and body ground. There should
be 0.5 V or less.
SRS UNIT CONNECTOR A (18PI
Wire side oJ Jemale terminals
Is the voltage as specified?
YES Faulty SRS unit; replace the SRS unit (see
page 23'1221.a
NO Shortto power in dashboard wire harness B;
replace dashboard wire harness B.l
t'J
J

sRs
DTC Troubleshooting (cont'dl
8. Read the DTC.
ls DTC 22-3 indicated?
YES Go to slep 9.
NO-Short in the front passenger's seat belt buckle
tensioner; replace the front passenger's seat belt
buckle.l
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both side airbag 2P connectors (see
step 4 on page 23-21)and the driver's seat belt
buckle tensioner 4P connector (see step 6 on page
23-22).
'11. Disconnect SRS unit connector B {18P)from the
SRS unit (see step 7 on page 23-221.
12. Disconnect the special tool from the floor wire
h a rness.
13. Check resistance between the No.2 and No. 11
terminals of SRS unit connector B ( 18P). There
should be an open circuit, or at least 'l M !) .
SRS UNIT CONNECTOR B {18P}
GRN/RED
Wire side oI female terminals
ls the resistance as specified?
YES Faulty SRS unit; replace the SRS unit (see
page 23'1221 .a
NO Short in the floor wire harness; replace the
floor wire harness.I
GRN
23-66
\J
DTC 22-4: Short to Power in Front Passenger's
Seat Belt Buckle Tensioner
SpecialTools Required. SRS inflator simulator 07SAZ-TB4011A. SRS simulator lead F 07XAz 5230100
1. Erase the DTC memory (see p age 23-26).
2. Turn the ignition switch ON {ll}, and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SHS indicator stay on?
YES Go to step 3.
NO Inlermittentfailure,system isOKatthistime.
Go to Troubleshooting Intermittent Failures (see
page 23-261.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger's seat belt buckle
tensioner 4P connector (A) from the floor wire
narness.
5. Connect the SRS inflator simulator (2 !J
connectors) and simulator lead F to the floor wire
ha rness.
u

t
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
ls DTC 22-4 indicated?
YES Go to step g.
NO-Short to power in the front passenger,s seatbelt buckle tensioner; replace the front passenger,s
seat belt buckle. !
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes,
10.Disconnect both side airbag 2P connectors (see
step 4 on page 23-21)and the driver's seat beltbuckle tensioner 4P connector (see step 6 on page,1_r'>\
Disconnect SRS unit connector B (18P) from theSRS unit (see step 7 on page 23-221.
Disconnect the special tool from the floor wireharness.
Reconnect the battery negative cable.
Turn the ignition switch ON (ll).
Check for voltage between the No. 2 terminal ofSRS unit connector B {18P) and body ground, andthe No. 11 terminal and body ground. There shouldbe 0.5 V or Iess.
SRS UNIT CONNECTOR B I18P)
ls the voltage as specified?
YES-Faulty SRS unit; replace the SRS unit (see
page 23-1221 .l
NO Short to power in the floor wire harness;
replace the floor wire harness.l
11.
't2.
t5.
14.
23-67

sRs
DTC Troubleshooting (cont'dl
13. Check voltage between the No. 10 terminal of SRS
unit connector A (18P) and body ground. There
shouid be 'l V or less.
SRS UNIT CONNECTOR A {,I8P)
12378I
101112l3t4151611t6
RED
Wire side oI female terminals
ls the voltage as specitied?
YES-Go to step 14.
NO-Short to power in the engine compartment
wire harness or dashboard wire harness B; replace
the faulty harness.l
Turn the ignition switch OFF.
Connect the SRS inflator simulator (jumper
connector) and simulator lead H to the engine
compartment wire harness 2P connector (A).
07YAZ-S3AA100
07SAZ-TB,O11A
14.
t5.
23-78
\."r1
16. Check resistance between the No. 10 and No. 11
terminals of SRS unit connector A (18P). There
should be 1 0 or less.
SRS UNIT CONNECTOR A Il8PI
Wire side of female terminals
ls the rcsistance as specified?
YES Faulty left front impact sensor or SRS unit;
replace the left front impact sensor (see page 23-125).
lf the problem is still present, replace the SRS unit(see page 23-122).1
NO-Poor connection at C401, faulty engine
compartment wire harness, or faulty dashboard
wire harness B. Inspect C401. lf it is OK, replace the
faulty harness.l
= \y,

sRs
DTC Troubleshooting (cont'd)
13. Check voltage between the No. 1terminal ofSRS
unit connector A (18P) and body ground. There
should be 1 V or less.
SRS UNIT CONNECTOR A I18P}
Wire side of female terminals
ls the voltage as specified?
YES Go to step 14.
NO-Short to power in the engine compartment
wire harness or dashboard wire harness B; replace
the faulty harness.l
Turn the ignition switch OFF.
Connect the SRS inflator simulator (jumper
connector) and simulator lead H to the engine
compartment wire harness 2P connector (A).
14.
07YAZ-S3AA100
23-80
16. Check resistance between the No. 1 and No. '12
terminals of SRS unit connector A (18P). There
should be 1 O or less.
SRS UNIT CONNECTOR A {18P)
GRN
Wire side of female terminals
ls the resistance as specitied?
YES Faulty right front impact sensor or SRS unit;
replace the rightfront sensor {see page 23-125). lfthe
problem is still present, replace the SRS unit (see
page 23-1221.a
NO- Poor connection at C401, faulty engine
compartment wire harness, or faulty dashboard
wire harness B. lnspect C401. lf it is OK, replace the
faulty harness, I
LJ
J_lr12lr
tE.]I
/A
56789
t311r51611t6
BLK

I
I
8. Read the DTC.
ls DTC 11-3 indicated?
YES-Go to step 9.
NO*Shon to another wire in the driver's side
airbag inflator; replace the driver's side airbag (see
page 23-115).I
9. Turn the ignition switch OFF. Disconnect the
battery negative cable. and wait for 3 minutes.
10. Disconnectthe front passenger's side airbag 2P
connector (see step 4 on page 23-21) and both seat
belt buckle tensioner 4P connectors (see step 6 on
page 23-22l,.
11. Disconnect the special tool from the floor wire
harness 2P connector.
12. Disconnect SRS unit connector B {18P)from the
SRS unit {see step 7 on page 23-221.
13. Check resistance between the No.6 and No. 17
terminals of SRS unit connector B (18P), There
should be an open circuit, or at least 1 M 0.
SRS UNIT CONNECTOR B {18PI
Wire side of female terminals
ls the resistance as specified?
YES Faulty SRS unit; replace the SRS unit {seepage 23-'t221 .a
NO Shon to another wire in the floor wire
harness; replace the floor wire ha rness.I
WHT/BLU
WHT/BLK
DTG 11-4: Short to Power in Driver's Side
Airbag Inflator
Special Tools Required. SRS inflator simulator 07SAZ-T84011A. SRS simulator lead E o7XAZ-S140200
1. Erase the DTC memory {see page 23-261.
2. Turn the ignition switch ON (ll), and check thatthe
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SBS indicator stay on?
YES Go to step 3.
NO Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-26l,.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the driver's side airbag.
07sAz-TB4011A
5. Connect the SRS inflator simulator (2 0 connector)
and simulator lead E to the floor wire harness.
(cont'd)
23-83

sRs
DTC Troubleshooting (cont'd)
6. Reconnect the battery negative cable.
7. Erase the DTC memory,
8. Read the DTC.
Is DTC 11-4 indicated?
YES-Go to step 9.
NO Short to power in the driver's side airbag
inflator; replace the driver's side airbag (see page
23-115).t
Turn the ignition swilch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Disconnect the front passenger's side airbag 2P
connector (see step 4 on page 23-21) and both seat
belt buckle tensioner 4P connectors (see steD 6 on
page 23-221.
9.
'10.
23-84
\.J
11.Disconnect SRS unit connector B (18P) from the
SRS unit (see step 7 on page 23-22l,.
Turn the ignltion switch ON (ll).
Check for voltage between the No. 6 terminal of
SRS unit connector B (18P) and body ground, and
between the No. 17 terminal and body ground.
There should be 0.5 V or less.
SRS UNIT CONNECTOR B I18P)
WHT/BLK
ls the voltage as specitied?
YES- Faulty SRS uniU replace the SRS unit (see
page 23-1221.a
NO Short to power in the floor wire harness;
replace the floor wire harness.l
't2.
13.
UJ

sRs
DTC Troubleshooting (cont'dl
6. Reconnect the battery negative cable.
7, Erase the DTC memory.
8. Read the DTC.
ls DTC 12-3 indicated?
YES-Go to step I
NO Short to another wire in the front passenger's
side airbag inflator; replace the front passenger's
side airbag (see page 23-ll5).1
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver's side airbag 2P connector
(see step 4 on page 23-21) and both seat belt buckle
tensioner 4P connectors (see step 6 on page 23-22).
'!1. Disconnect the specialtoolfrom the floor wire
harness 2P connector.
12. Disconnect SRS unit connector B ('lSPlfrom the
SRS unit {see step 7 on page 23-221.
13. Check resistance between the No.7 and No. 18
terminals of sRS unit connector B (18P). There
should be an open circuit, or at least 1 M 0.
SRS UNIT CONNECTOR B I18P)
WHT/RED
-r-'r-Jl' 8lel n
i['tl,Bl S-T
236
10ll15
WHT/GRN
Wire side of {emale terminals
ls the resistance as specilied?
YES Faulty SRS unit; replace the SRS unit {seepage 23-1221.a
NO Short to anolher wire in the f loor wire
harness; replace the floor wire harness.I
23-88
\.J
DTC 12-4: Short to Power in Front Passenger's
Side Airbag Inf lator
Special Tools Required. sRS inflator simulator 07sAz-TB4011A. SRS simulator lead E 07XM-S140200
1. Erase the DTC memory (see page 23-26).
2. Turn the ignition switch ON (ll), and check thatthe
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicator stay on?
YES-Go to step 3.
NO- Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures {see
page 23-26).
3. Turn the ignition switch OFF. Disconnect the
banery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the front passenger's side airbag.
07xAz-s1A0200
5. Connect the SRS inflator simulator (2 Q connector)
and simu lator lead E to the floor wire harness.