change time HONDA CR-Z 2011 1.G User Guide

98
Controls
Setting the Clock
Clock
Models without navigation system
You can adjust the time in the clock display, using the CLOCK (AM/FM) button.Adjusting the Time

■
Press and hold the CLOCK button until the clock display begins to blink.
1.
Press the
2.
1 (Hour) button to change the hours.
Press the
3.
2 (Minute) button to change the minutes.
Press the CLOCK button to go back to the normal display.
4.
Button
Button
Button
(Power) Button
Clock Display
CLOCK Button
3
Clock
To set the time to the nearest hour: Press and hold the CLOCK button until the clock display begins to blink, then press the
3 (Reset)
button. Depending on the displayed time, the clock sets forward or backward.Example:1:06 will reset to 1:001:53 will reset to 2:00
Models with navigation system The clock is automatically updated through the navigation system, so the time does not need to be adjusted.
Main MenuTable of Contents

106
Controls
Security System Security Alarm System
Setting the Security Alarm System
■
The security alarm system automatically sets when the following conditions have been met:
The ignition switch is in LOCK
•
0, and the key has been removed from the
ignition switch. The hood is closed.
•
Both doors and the hatch are locked.
•
When the Security Alarm System Sets
■
The security system indicator in the instrument panel blinks. When the blinking interval changes after about 15 seconds, the security alarm system is set.
To Cancel the Security Alarm System
■
The security alarm system is canceled when the vehicle is unlocked using the key or remote transmitter. The security system indicator goes off at the same time.
Security Alarm System
Do not set the security alarm system when someone is in the vehicle or a window is open. The system can accidentally activate when unlocking the door with the lock tab or the master door lock switch. If the 12 volt battery goes dead after you have set the security alarm system, the security alarm may go off once the battery is recharged or replaced.If this occurs, deactivate the security alarm system by unlocking a door using the key or remote transmitter. Do not attempt to alter this system or add another device to it.
Main MenuTable of Contents

113
Controls
Operating the Switches Around the Steering Wheel Wipers and Washers
Wipers and Washers
Wipers and Washers
If the vehicle speeds up while the wipers are operating intermittently, the interval decreases by about four seconds. Also, when the vehicle starts moving, the wipers make a single sweep. In the shortest delay setting (
), the wipers
change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).
NOTICE Do not use the wipers when the windshield is dry. The windshield will get scratched, or the rubber blades will get damaged. Turn the washers off if no washer luid comes out. The pump may get damaged.
NOTICE In cold weather, the blades may freeze to the windshield, becoming stuck.Operating the wipers in this condition may damage the wipers. Use the defroster to warm the windshield, then turn the wipers on.
Front Wiper/Washer
■
The windshield wipers and washers can be used when the ignition switch is in ON
II.
MIST
■
The wipers run at high speed until you release the lever.
Wiper Switch (OFF, INT, LO, HI)
■
Change the wiper switch setting according to the amount of rain.
Adjusting the Delay
■
Turn the adjustment ring to adjust the wiper delay.
Washer
■
Sprays while you pull the lever toward you. When you release the lever, the wipers make two or three more sweeps before stopping.
Pull to use
washer.
Intermittent Time Adjustment Ring
MIST OFF
INT: IntermittentLO: Low speed wipeHI: High speed wipeLong delay Short delay
Main MenuTable of Contents

123
Controls
Interior Lights/Interior Convenience Items
Interior Lights
Interior Light Switch
■
Front interior lights are located between the sun visors. Rear interior lights are located at the back corner of each rear window.
■ON
The interior lights come on regardless of whether the doors are open or closed. Door Activated
■
The interior lights come on in the following situations:
When either of the doors are opened.
•
You unlock the driver’s door.
•
You remove the key from the ignition
•
switch.
OFF
■
The interior lights remain off regardless of whether the doors are open or closed. Each front interior light can be used as a map light. Each light can be turned on and off by pressing the lenses.
Interior Lights
In the door activated position, the interior lights fade out and go off about 30 seconds after the doors are closed.The lights go off after 30 seconds in the following situations: When you unlock the driver's door but do not

•
open it.When you remove the key from the ignition

•
switch but do not open a door.
The interior lights go off immediately in the following situations: When you lock the driver's door.

•
When you close the driver's door with the key in

•
the ignition switch. When you turn the ignition switch to ON

•
.
If you leave either door open without the key in th e
ignition switch, the interior lights go off after a bout
15 minutes. You can change the interior lights dimming time.
Customized Features P. 9 0
When the interior light switch is in the door activated position and either door is open, the front interior light will not go off when you press the lens.
Door Activated Position
On
OffFront
Rear
Main MenuTable of Contents

145
Features
Audio without Navigation System Playing a CD
Playing a CD Your audio system supports audio CDs, CD-Rs, and CD-RWs in either MP3 or WMA format. With the disc loaded, press the CD button.
Disc Slot Insert a CD about halfway into the disc slot.
(Disc Eject) Button
Press to eject a disc.
SEEK Buttons
Press or to change tracks (iles in MP3 or WMA). CD ButtonPress to play a CD.
VOL/SELECT
(Volume/Select) Knob
Turn to change tracks/iles. Turn to select an item, then press the VOL/SELECT knob to set your selection.
SCAN Button
You will get a 10-seconds sampling of each song.
• Press to sample all tracks on the disc (all iles in the current folder in MP3 or WMA).
• Press two times to sample the irst ile in each of the main folders (MP3 or WMA).
• To turn off scan, press and hold the button. RDM (Random) Button
• Press to play all tracks/iles on a disc in random order.
• Press two times to play all iles in the current folder (MP3 or WMA)
in random order.
• To turn off random, press and hold the button.
TITLE Button Press to display the text data on a CD (if it was recorded with text data).
/ Button
Press the button to skip to the next folder, and the button
to skip to the beginning of the previous folder in MP3 or WMA.
RPT (Repeat) Button
• Press to replay a track/ile continuously.
• Press two times to replay all iles in the current folder.
• To turn off repeat, press and hold the button.
(Power) Button
Press to turn the audio
system ON and OFF.
Main MenuTable of Contents

147
Features
Audio without Navigation System Playing an iPod®

Playing an iPod ®
Connect your iPod using your dock connector to the USB adapter cable, then press the AUX button.
Connecting an iPod/USB Flash Memory Device P.138
Button
Press to set your selection. AUX Button Press to select iPod
®
(if connected).
Button Press to go back to the previous
display.
VOL/SELECT
(Volume/Select) Knob
Turn to select a song, ile, menu item, or play mode. Press the VOL/SELECT knob to set. TITLE Button Press to display the text data.
RDM (Random) Button
• Press to play all available iles in a selected list (playlists, artists, albums
or songs) in random order.
• Press two times to play all available albums in a selected list (playlists, artists, albums or songs) in random
order.
•
To turn off shufle mode, press and
hold the button.
RPT (Repeat) Button
• Press to replay a ile continuously.•
To turn off repeat, press the button again.
SEEK Buttons
Press or to change songs. (Power) Button
Press to turn the audio
system ON and OFF.
Main MenuTable of Contents

149
Features
Audio without Navigation System Playing a USB Flash Memory Device
Your audio system reads and plays sound files on a USB flash memory device in either MP3, WMA or AAC *1
format.
Connect your USB flash memory device to the USB adapter cable, then press the AUX button.
Connecting an iPod/USB Flash Memory Device P.138
* 1: Only AAC format iles recorded with iTunes ®
are playable on this audio unit.
VOL/SELECT
(Volume/Select) Knob
Turn to select a ile, then press the
VOL/SELECT knob to play.
SCAN Button
You will get a 10-second sampling of each ile.
• Press to sample all iles in the current folder.
• Press two times to sample the irst ile in each of the main folders.
• To turn off scan, press and hold the button. RDM (Random) Button
• Press to play all iles in random
order.
• Press two times to play all iles in the current folder in random
order.
• To turn off random, press and hold the button.
TITLE ButtonPress to display the text data.
Press the button to skip to the next
folder, and the button to skip to the
beginning of the previous folder.
RPT (Repeat) Button
• Press to replay a ile continuously.
• Press two times to replay all iles in the current folder.
• To turn off repeat, press and hold the button.AUX ButtonPress to select USB lash memory device (if connected).
/ Button
SEEK Buttons
Press or to change iles. (Power) Button
Press to turn the audio
system ON and OFF.
Playing a USB Flash Memory Device
Main MenuTable of Contents

153
Features
Audio with Navigation System Audio System Basic Operation
Selecting the Background
■
There are three backgrounds to choose from when displaying sound levels: Level: The sound level is shown with the vertical bars.
Spectrum Analysis: The sound level appears as ripples of water.
Off Each time you touch the Background icon, the screen changes.
Operation with the Joystick

■
Use the joystick to select an icon on the screen and access some audio functions. Push left, right, up, or down to select an item. Press to set your selection.Joystick
Main MenuTable of Contents

156
Features
Audio with Navigation System Playing a Disc
Playing a Disc Your audio system supports audio CDs, CD-Rs, and CD-RWs in either MP3 or WMA format. With the disc loaded, press the CD/AUX button or touch the CD icon.
CD/AUX Button Press to play the disc.FOLDER BarPress ▲ to skip to the
next folder, and ▼ to
skip to the beginning of the previous folder in MP3 or WMA. Joystick
Navigation Display
AUDIO Button
Press to display the audio mode on the navigation screen. VOL/PWR
(Volume/Power) Knob
Press to turn the audio system
ON and OFF.
Turn to adjust the volume.
RPT (Repeat) Button
• Press to replay a track/ile continuously.
• Press and hold to replay all iles in the current folder (MP3 or WMA).
• To turn off repeat, press the button again.CD Icon
Touch to play the disc.
SCAN Button
You will get a 10-second sampling of each song.
• Press to sample all tracks on the disc (all iles in the current folder in MP3 or WMA).
• Press two times to sample the irst ile in each folder on the disc (MP3 or WMA).
• To turn off scan, press and hold the button. (Fast Forward/
Rewind) Buttons Press and hold to move rapidly within a track/ile.
RDM (Random) Button
• Press to play all tracks/iles in random order.
• Press and hold to play all iles in the current folder (MP3 or
WMA) in random order.
• To turn off random, press the button again. (Skip) Buttons
Press or to change tracks (iles in MP3 or WMA).
Main MenuTable of Contents

177
Features
Bluetooth ®
HandsFreeLink ®
HFL Menus
Phone Setup
■
To Pair a Cell Phone
■
If no phone has been paired to the system before, HFL gives you information
1.
about how to pair the first phone. If a phone has already been paired: say “Phone Setup” and “Pair” after the HFL prompts. Follow the HFL prompts and put your phone in discovery or search mode.
2.
HFL gives you a four-digit code and begins searching for your phone.
When your phone finds a
3. Bluetooth®
device, select HFL from the options and
enter the four-digit code. Follow the HFL prompts and name the newly paired phone.
4.
To Rename a Paired Phone
■
Say “Phone Setup.”
1.
Say “Edit” after the prompts.
2.
Follow the HFL prompts and rename the phone.
3.
If there is more than one phone paired to the system, HFL asks you which
phone’s name you want to change.
To Delete a Paired Phone
■
Say “Phone Setup.”
1.
Say “Delete” after the prompts.
2.
Follow the HFL prompts.
3.
HFL asks you which phone you want to delete.
Phone Setup
Press the
button and wait for a beep before
giving a command. Your Bluetooth -compatible phone must be paired
to HFL before you can make and receive hands-free calls. Phone Pairing Tips: You cannot pair your phone while the vehicle is

•
moving. Your phone must be in the discovery or search

•
mode when pairing the phone. Refer to your phone's manual.Up to six phones can be paired.

•
Your phone's battery may drain faster when it is

•
paired to HFL.If your phone is not ready for pairing or not

•
found by the system within three minutes, the system times out and returns to idle.
continued
Main MenuTable of Contents