ECU HONDA CR-Z 2011 1.G Owner's Manual

140
Features
Audio System Audio System Theft Protection
Audio System Theft Protection
The audio system is disabled when it is disconnected from the power source, such as when the 12 volt battery is disconnected or goes dead.Entering the Audio Security Code
■
“ENTER CODE” appears on the display when the power is reconnected.
Turn on the audio system.
1.
Enter the security code using the preset buttons.
2.
Models with navigation system
Touch the icon to enter the code, then touch the Done icon to set it. If you enter an incorrect digit, continue to the last digit, then try again. If you do not enter the code correctly after 10 tries, you need to visit a dealer to have the system reset.
Audio System Theft Protection
Find the audio system's security code and serial number on the radio code card.
Do not store the card in your vehicle. If you lose the
radio code card, you must obtain the information from a dealer.
Main MenuTable of Contents

176
Features
Bluetooth ®
HandsFreeLink ®
HFL Menus
"Phonebook""Store"
"Edit"
"Delete"
"Receive contact" *
"List"
"Security"
"Change passcode"
"Call notication"
"Auto transfer"
"Clear"
"Change language" *
"Tutorial"
"Hands-free help"
"System setup"
Switch the s ystem language b etwe en English and French.
He ar a tutorial for general rules on using the s ystem .
He ar a lis t of available commands and additional information describing each command .
St
ore a phonebook e ntry.
Edi t the num ber of an exi sting phonebo ok entry.
Delet e a phonebo ok entry.
He ar a list of all s tored phonebo ok entries.
Tr an sfer con tacts from your phone to H FL.
Ch ange your s ecurity pas scode.
Set how y ou want to be notiied of an incoming c all.
Set t o automatic ally transfer c alls from your phone to H FL when you
enter the vehicle .
Ap
ply a securit y passcode t o the s ystem that mus t be input at each
ke y c ycle to acces s the system.
Cl ear the s ystem of all paired phones, phonebo ok entries, and
se curit y pas scode.
*Not available on all models
Main MenuTable of Contents

188
Features
Bluetooth ®
HandsFreeLink ®
HFL Menus
System Setup
■
This command group allows you to change or customize HFL basic settings.
To Set a Four-digit Passcode to Lock the HFL System for Security
■
Say “System Setup.”
1.
Say “Security.”
2.
Follow the HFL prompts and say the four-digit number of your choice.
3.
Follow the HFL prompts and confirm the number.
4.
To Change the Security Passcode
■
Say “System Setup.”
1.
Say “Change Passcode” after the prompts.
2.
Say the new four-digit passcode after the HFL prompts.
3.
Follow the HFL prompts.
4.
To Select a Ring Tone or a Prompt as the Incoming Call Notification
■
Say “System Setup.”
1.
Say “Call Notification” after the prompts.
2.
Say “Ring Tone” or “Prompt” after the prompts. For no audible notification, say
3.
“Off.”
System Setup
Press the
button before a command.
Once a passcode is set, you are required to enter the passcode with every new key cycle to use HFL.If you forget the code, go to your dealer to have the passcode reset. You can also cancel the passcode by clearing all the data stored in the HFL system.
To Clear the System P.1 8 9
The default setting of the incoming notiication is a prompt.
Main MenuTable of Contents

192
Driving
Before Driving
Driving Preparation
Check the following items before you start driving.Check Items Before Getting In the Vehicle

■
Make sure there is no obstruction on the windows, door mirrors, exterior lights,

•
or other parts of the vehicle.
Remove any frost, snow, or ice.
Remove any snow on the roof, as this can slip down and obstruct your field of
vision while driving. When frozen hard, remove ice once it has softened.
When removing ice from around the wheels, be sure not to damage the wheel or wheel components.
Make sure the hood is securely closed.

•
If the hood opens while driving, your front view will be blocked.
Make sure the tires are in good condition.

•
Check air pressures, and check for damage and excessive wear.
Checking and Maintaining Tires P.269
Make sure there is no person or object behind or around the vehicle.

•
There are blind spots from the inside.
Check Items in the Compartment

■
Store or secure all items on board properly.

•
Carrying too much cargo, or improperly storing it, can affect your vehicle’s
handling, stability, stopping distance, and tires, and make it unsafe.
Maximum Load Limit P.194
Do not pile items higher than the seat height.

•
They can block your view and may be thrown forward in the event of sudden
braking.
Check Items Before Getting On the Vehicle
NOTICE If the doors are frozen shut, use warm water around the door edges to melt any ice. Do not try to force them open, as this can damage the rubber trim around the doors. When done, wipe dry to avoid further freezing. Do not pour warm water into the key cylinder. You will be unable to insert key if the hole freezes.
Check Items in the Compartment
The headlight aim is set by the factory, and typically does not need to be adjusted. However, if you regularly carry heavy items in the cargo area, have the aiming readjusted at your dealer or by a qualiied technician.
Main MenuTable of Contents

193
Driving
Before Driving Driving Preparation
Do not place anything in the seat footwells. Make sure to secure the floor mats.

•
An object or unsecured floor mat can interfere with your brake and
accelerator pedal operation while driving.
If you have any animals on board, do not let them move around in the vehicle.

•
They may interfere with driving and a crash could occur.
Securely close and lock both doors and the hatch.

•
Locking and Unlocking the Doors from Inside P.102
Adjust your seating position properly.

•
Adjusting the Seats P.119
Adjust the mirrors and steering wheel properly for your driving.

•
Adjust them while sitting in the proper driving position.
Adjusting the Mirrors P.118
Steering Wheel Adjustments P.117
Be sure items placed on the floor behind the driver’s and passenger’s seats

•
cannot roll under the seats.
They can interfere with the driver’s ability to operate the pedals, the operation
of the seats, or the operation of the sensors under the seats.
Everyone in the vehicle must fasten their seat belt.

•
Fastening a Seat Belt P.37
Make sure that the indicators in the instrument panel come on when you start

•
the vehicle, and go off soon after.
Always have a dealer check the vehicle if any of the indicators indicate a
problem.
Indicators P.68
Main MenuTable of Contents

246
Maintenance
Maintenance Under the Hood Opening the Hood
Opening the Hood1. Park the vehicle on a level surface, and set the parking brake.Pull the hood release handle under the
2.
lower left corner of the dashboard.
The hood will pop up slightly.
3. Push up the hood latch lever in the center
of the hood to release the lock mechanism, and open the hood.
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
Hood Release Handle
Pull
Opening the Hood
NOTICE Do not open the hood when the wiper arms are raised.The hood will strike the wipers, and may damage either the hood or the wipers. When closing the hood, check that the hood is securely locked. If the hood latch lever moves stifly, or if you can open the hood without lifting the lever, the mechanism should be cleaned and lubricated. Do not open the hood while the auto idle stop function is activated.
Lever
Support Rod
Grip
Clamp
Main MenuTable of Contents

249
Maintenance
Maintenance Under the Hood Adding Engine Oil
Adding Engine Oil1. Unscrew and remove the engine oil fill cap. Slowly pour in the oil.
2.
Reinstall the engine oil fill cap, and tighten
3.
it securely.Wait for several minutes and recheck the
4.
engine oil dipstick.
Engine Oil Fill Cap
Adding Engine Oil
If any oil spills, wipe it up immediately. Spilled oil may damage the engine compartment components.
NOTICE Do not ill the engine oil above the upper limit
mark. Overilling the engine oil may result in engin e
damage.
Main MenuTable of Contents

254
Maintenance
Maintenance Under the Hood Transmission Fluid
Transmission Fluid
Automatic Transmission Fluid
■
Continuously Variable Transmission (CVT)
■
Specified fluid: Honda CVTF (continuously variable transmission fluid)
Check the fluid level when the engine is at normal operating temperature. 1. Park on level ground, and start the engine. Wait until the radiator fan starts and then
2.
turn off the engine.
Perform step 3 after waiting for about 60 seconds (less than 90 seconds).
Remove the dipstick (yellow loop) from the
3.
transmission and wipe it with a clean cloth. Insert the dipstick all the way back into
4.
the transmission securely, as shown in the image. Remove the dipstick again and check the
5.
fluid level.
It should be between the upper and lower marks in the HOT range.
If the level is below the lower mark, add
6.
fluid into the dipstick hole to bring it to the level between the upper and lower marks, and have your vehicle checked by a dealer immediately.
Pour the fluid slowly and carefully
so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
Upper Mark Lower Mark
HOT Range
Main MenuTable of Contents

278
Maintenance
12 Volt Battery
Checking the 12 Volt Battery
Check the battery condition monthly. Look at the test indicator window and check the terminals for corrosion.
If your vehicle’s battery is disconnected or goes dead: The audio system is disabled.
•
Entering the Security Code P.140
The clock resets.
•
Setting the Clock P.98
The navigation system is disabled. A PIN code will be required.
•
Refer to the navigation system manual.
Charging the 12 Volt Battery Disconnect both battery cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (–) cable first, and reconnect it last.
Test Indicator Window 12 Volt Battery
WARNING: Battery posts, terminals, and
related accessories contain lead and lead compounds.Wash your hands after handling. The test indicator's color information is on the battery. When you ind corrosion, clean the battery terminals by applying a baking powder and water solution. Rinse the terminals with water. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion. If the 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading may show less than the actual level the next time you turn the ignition switch to ON
. It will show the correct
level after you drive for about 30 minutes.
WARNING
The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled technician do any battery maintenance.
Main MenuTable of Contents

282
Maintenance
Cleaning Interior Care
Floor Mats
■
The driver’s floor mat hooks over the floor anchors, which keep the mat from sliding forward. To remove the mat for cleaning, turn each anchor knob to the unlock position. When reinstalling the mat after cleaning, turn each knob to the lock position. Do not put additional floor mats on top of the anchored mat.
Maintaining Genuine Leather

■*
Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats and seams. Clean the leather with a soft cloth dampened with a 90% water and 10% neutral wool detergent solution. Then buff it with a clean, dry cloth. Remove any dust or dirt on leather surfaces immediately.
Floor Mats
If you use any loor mats that were not originally provided with your vehicle, make sure they are designed for your speciic vehicle, it correctly and are securely anchored by the loor anchors.
Driver’s loor mat is shown.
Unlock
Lock
* Not available on all models
Main MenuTable of Contents