ignition HONDA CR-Z 2011 1.G Workshop Manual

198
Driving
When Driving Starting the Engine
3. Turn the ignition switch to START
without depressing the accelerator pedal.
Starting to Drive

■
Automatic transmission (CVT) model
Keeping your right foot on the brake pedal, release the parking brake. Check
1.
that the brake system indicator has gone off.
Parking Brake P.219
Put the shift lever in
2.
D. Select R when reversing.
Gradually release the brake pedal and gently depress the accelerator pedal to
3.
pull away.
Starting the Engine
Do not hold the key in START
for more than 15
seconds.
If the engine does not start right away, wait for

•
at least 10 seconds before trying again. If the engine starts, but then immediately stops,

•
wait at least 10 seconds before repeating step 3 while gently depressing the accelerator pedal. Release the accelerator pedal once the engine starts.
The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine's fuel system is disabled.
Immobilizer System P.1 0 5
Main MenuTable of Contents

200
Driving
When Driving Precautions While Driving
Precautions While Driving
In Rain
■
Avoid driving in deep water and on flooded roads. This can damage the engine or cause electrical component failure.
Other Precautions

■
If there is a strong impact with something under the vehicle, stop in a safe location. Check the underside of the vehicle for damage and fuel or brake fluid leaks.
Precautions While Driving
NOTICE Do not operate the shift lever while pressing the accelerator pedal. You could damage the transmission. If the ignition switch is turned to ACCESSORY

or LOCK while driving, the engine will shut
down and all steering and brake power assist functions will stop, making it dificult to control the vehicle. Do not drive with the shift lever in
, as you will
lose engine braking (and acceleration) performance. During the irst 600 miles (1,000 km) of operation, avoid sudden acceleration or full throttle operation so as to not damage the engine or powertrain. Avoid hard braking for the irst 200 miles (300 km). You should also follow this when the brakes are replaced.
Main MenuTable of Contents

202
Driving
When Driving Shifting
Shifting
Automatic transmission (CVT) model
Change the shift position in accordance with your driving need.Names and Functions of Shift Lever Positions
■
Shifting
You cannot turn the ignition switch to LOCK

and remove the key unless the shift lever is in .
The vehicle may move forward very slightly even in
while the engine is cold.
Depress the brake pedal irmly and, when necessary, apply the parking brake. The engine may cut in and out in
R or depending
on the road condition, even when the engine
speed is lower than the tachometer’s red zone. This is the engine’s computer working to protect the transmission.
Park Used when parking or starting the engine. Reverse Used when backing up. Neutral Used when idling Drive Used for:
~
Normal driving
~
Temporarily driving in the 7-speed manual shift mode (when driving in ECON or NORMAL mode)
~
Driving in the 7-speed manual shift mode (when driving in SPORT mode)
~
Driving in L mode
Main MenuTable of Contents

209
Driving
When Driving Shifting
Reverse Lockout
■
The manual transmission has a lockout mechanism that stops you from accidentally shifting into
R from a forward gear while the vehicle is moving at a certain speed.
If you cannot shift to
R when the vehicle is stopped, do the following: 1. Depress the clutch pedal, move the shift lever all the way to the left, and shift to
R.
If you still cannot shift into
2.
R, apply the
parking brake, and turn the ignition switch to ACCESSORY
I or LOCK 0.
Depress the clutch pedal and shift into
3.
R.
Keep depressing the clutch pedal and start
4.
the engine.
Have the vehicle checked by a dealer if you have to go through this procedure repeatedly.
Main MenuTable of Contents

210
Driving
When Driving 3-Mode Drive System
3-Mode Drive System Driving mode is in NORMAL when you turn the ignition switch to ON
II.
To change driving modes, press the desired mode button. The corresponding mode indicator comes on in the instrument panel, and the mode icon appears briefly on the multi-information display. 3-Mode Drive System
To keep the system in the ECON mode the next
time the ignition switch is turned to ON
, change
the customized setting on the multi-information display.
Customized Features P. 9 0
The ECON mode helps you improve your fuel economy by changing the engine, transmission, climate control system, cruise control, and IMA system performances. While in the ECON mode, the climate control system has greater temperature luctuations.
Ù Select a driving mode
and press the button.
Ù The selected driving mode
indicator comes on.
SPORT Mode Button NORMAL Mode Button ECON Mode Button
Main MenuTable of Contents

211
Driving
When Driving Cruise Control
Cruise Control Maintains a constant vehicle speed without having to keep your foot on the accelerator. Use cruise control on freeways or open roads where you can travel at a constant speed with little acceleration or deceleration.
Cruise Control
When the ignition switch is in ACCESSORY
or
LOCK , cruise control automatically goes off.
It may not be possible to maintain a constant speed when driving uphill or downhill. When climbing a steep hill with the ECON mode, it may take relatively more time to accelerate to maintain the set speed. When not using cruise control, turn off cruise control by pressing the CRUISE button.
Manual transmission While the cruise control system is activated, the shift up or down indicator does not work.
WARNING
Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather.When to use
How to use
Ù Vehicle speed for cruise control:
Desired speed in a range above roughly 25 mph (40 km/h). Always keep sufcient distance between you and the vehicle in front of you.
CRUISE MAIN is on in the instrument panel. Cruise control is ready to use.
Automatic transmission model
Ù Press the CRUISE button on the
steering wheel.
Main MenuTable of Contents

241
Maintenance
Maintenance Minder™
If the engine oil life is less than 15%, you will see the maintenance minder messages appear on the multi-information display every time you turn the ignition switch to ON
II. The messages notify you when to change the engine oil, or when to bring
your vehicle to a dealer for indicated maintenance services.
Displaying the Engine Oil Life

■
Turn the ignition switch to ON
1. II.
Press the
2.
button repeatedly until the engine oil life appears on the
multi-information display.
The system message indicator (
) comes on along with the maintenance minder
message.
Displaying the Engine Oil Life
Based on the engine operating conditions, the remaining engine oil life is calculated and displayed as a percentage.
Displayed Engine Oil
Life (%) Calculated Engine
Oil Life (%)
100 100 to 91 90 90 to 81
80 80 to 71
70 70 to 61
60 60 to 51
50 50 to 41
40 40 to 31
30 30 to 21
20 20 to 16
15 15 to 11
10 10 to 65 5 to 1
0 0
Maintenance Service Items
Remaining Engine Oil Life
(Information) Buttons
Main MenuTable of Contents

244
Maintenance
Maintenance Minder™
Resetting the Display
■
Reset the engine oil life display if you have performed the maintenance service.
Turn the ignition switch to ON
1.
II.
Display the engine oil life by repeatedly pressing the
2.
button.
Press and hold the SEL/RESET button for 10 seconds or more.
3.
The oil life reset mode is displayed on the multi-information display.
Select “RESET” with the
4.
button, then press the SEL/RESET button.
The service code will disappear and the engine oil life display will return to
100 %.
To cancel the oil life reset mode, select “CANCEL”, then press the SEL/RESET button.
Resetting the Display
NOTICE Failure to reset the engine oil life after a maintenance service results in the system showing incorrect maintenance intervals, which can lead to serious mechanical problems. The dealer will reset the engine oil life display after completing the required maintenance service.If someone other than a dealer performs
maintenance service, reset the engine oil life disp lay
yourself.
Maintenance Item Codes
Engine Oil Life
SEL/RESET Button
(Information) Button
Main MenuTable of Contents

278
Maintenance
12 Volt Battery
Checking the 12 Volt Battery
Check the battery condition monthly. Look at the test indicator window and check the terminals for corrosion.
If your vehicle’s battery is disconnected or goes dead: The audio system is disabled.
•
Entering the Security Code P.140
The clock resets.
•
Setting the Clock P.98
The navigation system is disabled. A PIN code will be required.
•
Refer to the navigation system manual.
Charging the 12 Volt Battery Disconnect both battery cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (–) cable first, and reconnect it last.
Test Indicator Window 12 Volt Battery
WARNING: Battery posts, terminals, and
related accessories contain lead and lead compounds.Wash your hands after handling. The test indicator's color information is on the battery. When you ind corrosion, clean the battery terminals by applying a baking powder and water solution. Rinse the terminals with water. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion. If the 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading may show less than the actual level the next time you turn the ignition switch to ON
. It will show the correct
level after you drive for about 30 minutes.
WARNING
The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled technician do any battery maintenance.
Main MenuTable of Contents

287
Handling the Unexpected
If a Tire Goes Flat
Changing a Flat Tire
Changing a Flat Tire
Periodically check the tire pressure of the compact spare. It should be set to the speciied pressure.Speciied Pressure: 60 psi (420 kPa, 4.2 kgf/cm 2
)
When driving with the compact spare tire, keep the vehicle speed under 50 mph (80 km/h).Replace with a full size tire as soon as possible. The compact spare tire and wheel in your vehicle are speciically for this model.Do not use them with another vehicle.Do not use another type of compact spare tire or wheel with your vehicle. Do not mount tire chains on a compact spare tire. If a chain-mounted front tire goes lat, remove one of the full-size rear tires and replace it with the compact spare tire. Remove the lat front tire and replace it will the full size tire that was removed from the rear. Mount the tire chains on the front tire.
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the flat tire with the compact spare tire. Go to a dealer as soon as possible to have the full size tire repaired or replaced.
Park the vehicle on firm, level, and non-slippery ground.
1.
Put the shift lever in
2.
P (CVT).
Put the shift lever in
R (manual transmission).
Set the parking brake.
3.
Turn on the hazard warning lights and turn the ignition switch to LOCK
4.
0.
Main MenuTable of Contents