lock HONDA CR-Z 2011 1.G Repair Manual

278
Maintenance
12 Volt Battery
Checking the 12 Volt Battery
Check the battery condition monthly. Look at the test indicator window and check the terminals for corrosion.
If your vehicle’s battery is disconnected or goes dead: The audio system is disabled.
•
Entering the Security Code P.140
The clock resets.
•
Setting the Clock P.98
The navigation system is disabled. A PIN code will be required.
•
Refer to the navigation system manual.
Charging the 12 Volt Battery Disconnect both battery cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative (–) cable first, and reconnect it last.
Test Indicator Window 12 Volt Battery
WARNING: Battery posts, terminals, and
related accessories contain lead and lead compounds.Wash your hands after handling. The test indicator's color information is on the battery. When you ind corrosion, clean the battery terminals by applying a baking powder and water solution. Rinse the terminals with water. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion. If the 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading may show less than the actual level the next time you turn the ignition switch to ON
. It will show the correct
level after you drive for about 30 minutes.
WARNING
The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled technician do any battery maintenance.
Main MenuTable of Contents

282
Maintenance
Cleaning Interior Care
Floor Mats
■
The driver’s floor mat hooks over the floor anchors, which keep the mat from sliding forward. To remove the mat for cleaning, turn each anchor knob to the unlock position. When reinstalling the mat after cleaning, turn each knob to the lock position. Do not put additional floor mats on top of the anchored mat.
Maintaining Genuine Leather

■*
Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats and seams. Clean the leather with a soft cloth dampened with a 90% water and 10% neutral wool detergent solution. Then buff it with a clean, dry cloth. Remove any dust or dirt on leather surfaces immediately.
Floor Mats
If you use any loor mats that were not originally provided with your vehicle, make sure they are designed for your speciic vehicle, it correctly and are securely anchored by the loor anchors.
Driver’s loor mat is shown.
Unlock
Lock
* Not available on all models
Main MenuTable of Contents

287
Handling the Unexpected
If a Tire Goes Flat
Changing a Flat Tire
Changing a Flat Tire
Periodically check the tire pressure of the compact spare. It should be set to the speciied pressure.Speciied Pressure: 60 psi (420 kPa, 4.2 kgf/cm 2
)
When driving with the compact spare tire, keep the vehicle speed under 50 mph (80 km/h).Replace with a full size tire as soon as possible. The compact spare tire and wheel in your vehicle are speciically for this model.Do not use them with another vehicle.Do not use another type of compact spare tire or wheel with your vehicle. Do not mount tire chains on a compact spare tire. If a chain-mounted front tire goes lat, remove one of the full-size rear tires and replace it with the compact spare tire. Remove the lat front tire and replace it will the full size tire that was removed from the rear. Mount the tire chains on the front tire.
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the flat tire with the compact spare tire. Go to a dealer as soon as possible to have the full size tire repaired or replaced.
Park the vehicle on firm, level, and non-slippery ground.
1.
Put the shift lever in
2.
P (CVT).
Put the shift lever in
R (manual transmission).
Set the parking brake.
3.
Turn on the hazard warning lights and turn the ignition switch to LOCK
4.
0.
Main MenuTable of Contents

289
Handling the Unexpected
If a Tire Goes Flat Changing a Flat Tire
5. Place wheel blocks or rocks in front and rear of the wheel diagonal to the flat tire.
6. Place the compact spare tire (wheel side up) under the vehicle body, near the tire that needs to be replaced.
7. Loosen each wheel nut about one turn using the wheel nut wrench.
The tire to be replaced.
Wheel Blocks
Main MenuTable of Contents

290
Handling the Unexpected
If a Tire Goes Flat Changing a Flat Tire
How to Set Up the Jack
■
1. Place the jack under the jacking point closest to the tire to be changed.
2. Turn the end bracket (as shown in the image) clockwise until the top of the jack contacts the jacking point.
Make sure that the jacking point tab is
resting in the jack notch.
3. Raise the vehicle, using the extension bar and the jack handle, until the tire is off the ground.
Changing a Flat Tire
Do not use the jack with people or luggage in the vehicle. Use the jack provided in your vehicle. Other jacks may not support the weight ("load") or their shape may not match the jacking point.The following instructions must be followed to use the jack safely. Do not use while the engine is running.
•
Use only where the ground is irm and level.
•
Use only at the jacking points.
•
Do not get in the vehicle while using the jack.
•
Do not put anything on top of or underneath
•
the jack.
WARNING
The vehicle can easily roll off the jack, seriously injuring anyone underneath. Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.
Wheel Nut
Wrench as Jack Handle
Extension Bar
Main MenuTable of Contents

296
Handling the Unexpected
Shift Lever Does Not Move
Automatic transmission (CVT) model
Follow the procedure below if you cannot move the shift lever out of P position.
Releasing the Lock

■
1. Set the parking brake. Remove the key from the ignition switch.
2.
Wrap a cloth around the tip of a small flat-
3.
tip screwdriver and remove the cover of the shift lock release slot.
Put the tip of the flat-tip screwdriver into the slot and remove it as shown in the image.
4. Insert the key into the shift lock release slot.While pushing on the key, press the shift
5.
lever release button and place the shift lever into
N.
The lock is now released. Have the shift lever checked by a dealer as soon as possible.
SlotCover
Shift Lock Release Slot
Release Button
Main MenuTable of Contents

304
Handling the Unexpected
Fuses
Fuse Locations
If any electrical devices are not working, turn the ignition switch to LOCK 0 and
check to see if any applicable fuse is blown.
Engine Compartment Fuse Box

■
Located near the + terminal on the 12 volt battery.
1. Pull on the tab to release the front of the cover.Pull up the cover by pushing the two tabs
2.
as shown. Replacement of engine compartment fuses should be done by a dealer.
Circuit Protected and Amps for Each
■
Fuse
Circuit Protected Amps
1 Battery 100 A
2 EPS 70 A
3 Horn, Stop, Hazard 20 A
Fuse Locations
Fuse locations are shown on the fuse box cover.
Locate the fuse in question by the fuse number and box cover number.
Fuse Box
Main MenuTable of Contents

305
Handling the Unexpected
Fuses Fuse Locations
Interior Fuse Box
■
Located under the driver side dashboard.
Circuit Protected and Amps for Each Fuse
■
Fuse Locations
Fuse locations are shown on the label on the back side of the cover.
Locate the fuse in question by the fuse number and label number.
Label
Fuse BoxCover
Circuit Protected Amps
1 Back Up 15 A
2 TPMS* 1
7.5 A
3 Driver’s Power Window 20 A
4 - -
5 Back-Up Light 10 A
6 SRS 10 A
7 Transmission* 2
10 A
8 SRS 7.5 A
9 Fog Light* 20 A
10 A/C 7.5 A
11 ABS/VSA ®
7.5 A
12 IMA 10 ACircuit Protected Amps
13 Accessory Power Socket 20 A
14 Radio 7.5 A
15 Daytime Running Lights 7.5 A
16 Rear Wiper 10 A17 Passenger’s Power Window 20 A
18 - -
19 - -
20 Fuel Pump 15 A
21 Washer 15 A
22 Meter 7.5 A
23 Hazard 10 A
24 Stop/Horn 10 ACircuit Protected Amps
25 Audio AMP* 20 A
26 LAF 10 A
27 Door Lock Main 20 A
28 Headlight Main 20 A
29 Small Light 10 A
30 Main Fan Motor 30 A
31 IGPS 7.5 A
32 Right Headlight Low* 3
Right Headlight Low (HID)* 410 A 15 A
*1: U.S. models only *2: Automatic transmission (CVT)*3: Vehicle with halogen bulb low beam headlights*4: Vehicle with discharge headlights
continued
* Not available on all models
Main MenuTable of Contents

306
Handling the Unexpected
Fuses Fuse Locations
Circuit Protected and Amps for Each Fuse
■
Circuit Protected Amps
33 Ignition Coil 15 A 34 Left Headlight Low*
1
Left Headlight High* 210 A 10 A
35 Door Lock 7.5 A
36 Door Lock 10 A
37 ABS FSR/VSA ®
FSR 30 A
38 - -
39 IGP 15 A
40 - -
41 - -
42 IMA 1 7.5 A
43 MG Clutch 7.5 A
44 STS 7.5 A
45 Door Lock 20 A
46 - -
47 Sub Fan Motor 30 A 48 Left Headlight High*
1
Left Headlight Low (HID)* 210 A 15 A
49 Door Lock Motor 2
(UNLOCK) 7.5 A
50 - -
51 Right Headlight High 10 A
52 DBW 15 A
53 IMA 2 15 A
54 - -Circuit Protected Amps
55 Heated Mirror* 10 A
56 Front Wiper 30 A
57 Blower Motor 30 A
58 ABS/VSA ®
MTR 30 A
59 Rear Defogger 40 A*
3
30 A* 4
60 IG Main 50 A
61 - -
62 - -
*1: Vehicle with halogen bulb low beam headlights *2: Vehicle with discharge headlights*3: With heated door mirror*4: Without heated door mirror
* Not available on all models
Main MenuTable of Contents

307
Handling the Unexpected
Fuses Inspecting and Changing Fuses
Inspecting and Changing Fuses1. Turn the ignition switch to LOCK
0. Turn
headlights and all accessories off. Check the fuses in the engine
2.
compartment.
If the fuse is blown, have it replaced by a dealer.
3. Inspect the small fuses in the vehicle interior.
If there is a burned out fuse, remove it
with the fuse puller and replace it with a new one.
Fuse
Blown
Inspecting and Changing Fuses
NOTICE Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement fuse with the proper rating for the circuit, install one with a lower rating. Replace fuse with a spare fuse of the same speciied amperage.Conirm the speciied amperage using the charts on P.304 to P.306. There is a fuse puller on the interior fuse box.
Fuse Puller
Main MenuTable of Contents