lock HONDA CR-Z 2011 1.G Workshop Manual

211
Driving
When Driving Cruise Control
Cruise Control Maintains a constant vehicle speed without having to keep your foot on the accelerator. Use cruise control on freeways or open roads where you can travel at a constant speed with little acceleration or deceleration.
Cruise Control
When the ignition switch is in ACCESSORY
or
LOCK , cruise control automatically goes off.
It may not be possible to maintain a constant speed when driving uphill or downhill. When climbing a steep hill with the ECON mode, it may take relatively more time to accelerate to maintain the set speed. When not using cruise control, turn off cruise control by pressing the CRUISE button.
Manual transmission While the cruise control system is activated, the shift up or down indicator does not work.
WARNING
Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather.When to use
How to use
Ù Vehicle speed for cruise control:
Desired speed in a range above roughly 25 mph (40 km/h). Always keep sufcient distance between you and the vehicle in front of you.
CRUISE MAIN is on in the instrument panel. Cruise control is ready to use.
Automatic transmission model
Ù Press the CRUISE button on the
steering wheel.
Main MenuTable of Contents

219
Driving
Braking
Brake System
Parking Brake
■
Use the parking brake to keep the vehicle stationary when parking.
To apply: Pull the lever fully up without pressing the release button. To release:
Pull the lever slightly, and press and hold
1.
the release button. Lower the lever down all the way, then
2.
release the button.
Parking Brake
NOTICE Release the parking brake fully before driving. The rear brakes and axle can be damaged if you drive with the parking brake applied. If you start driving without fully releasing the parking brake, a buzzer sounds as a warning, and "RELEASE PARKING BRAKE" appears on the multi-information display. Always apply the parking brake when parking.When the outside temperature is extremely cold, do not apply the parking brake to prevent it from freezing, and do the following:
Automatic transmission model Put the shift lever in , then place a block or other
wheel chock to stop the wheels from turning.
Manual transmission model Put the shift lever in or , then place a block
or other wheel chock to stop the wheels from turning.
Main MenuTable of Contents

220
Driving
Braking Brake System
Foot Brake
■
Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The brake assist system increases the stopping force when you depress the brake pedal hard in an emergency situation. The anti-lock brake system (ABS) helps you retain steering control when braking very hard.
Brake Assist System P.222
ABS (Anti-lock Brake System) P.221
Foot Brake
Check the brakes after driving through deep water, or if there is a buildup of road surface water. If necessary, dry the brakes by lightly depressing the pedal several times. If you hear a continuous metallic friction sound when applying the brakes, the brake pads need to be replaced. Have the vehicle checked by a dealer.
Constantly using the brake pedal while going down a long hill builds up heat, which reduces the brake effectiveness. Apply engine braking by taking your foot off the accelerator pedal and downshifting to a lower gear. With manual transmission use a lower gear for greater engine braking. Do not rest your foot on the brake pedal while driving, as it will lightly apply the brakes and cause them to lose effectiveness over time and reduce pad life. It will also confuse drivers behind you.
Main MenuTable of Contents

221
Driving
Braking ABS (Anti-lock Brake System)
ABS (Anti-lock Brake System)
ABS
■
Helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than you can do. The electronic brake distribution (EBD) system, which is part of the ABS, also balances the front-to-rear braking distribution according to vehicle loading. You should never pump the brake pedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as “stomp and steer.”
ABS Operation
■
The brake pedal may pulsate slightly when the ABS is working. Keep holding the pedal firmly down. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice. When the vehicle speed goes under 6 mph (10 km/h), the ABS stops.
ABS (Anti-lock Brake System)
NOTICE The ABS may not function correctly if you use an incorrect tire type and size. When the ABS indicator comes on while driving, there may be a problem with the system.While normal braking is not affected, there is a possibility of the ABS not operating. Have the vehicle checked by a dealer immediately. The ABS does not reduce the time or distance it takes to stop the vehicle. It only helps with steering control during hard braking. In the following cases, your vehicle may need more stopping distance than a vehicle without ABS: When driving on rough road surfaces, including

•
when driving on uneven surfaces, such as gravel or snow.When tire chains are installed.

•
You may hear a motor sound coming from the
engine compartment while system checks are being performed immediately after starting the engine or while driving. This is normal.
Main MenuTable of Contents

246
Maintenance
Maintenance Under the Hood Opening the Hood
Opening the Hood1. Park the vehicle on a level surface, and set the parking brake.Pull the hood release handle under the
2.
lower left corner of the dashboard.
The hood will pop up slightly.
3. Push up the hood latch lever in the center
of the hood to release the lock mechanism, and open the hood.
4. Remove the support rod from the clamp using the grip. Mount the support rod in the hood.
When closing, remove the support rod, and stow it in the clamp, then gently lower the hood. Remove your hand at a height of approximately 12 inches (30 cm) and let the hood close.
Hood Release Handle
Pull
Opening the Hood
NOTICE Do not open the hood when the wiper arms are raised.The hood will strike the wipers, and may damage either the hood or the wipers. When closing the hood, check that the hood is securely locked. If the hood latch lever moves stifly, or if you can open the hood without lifting the lever, the mechanism should be cleaned and lubricated. Do not open the hood while the auto idle stop function is activated.
Lever
Support Rod
Grip
Clamp
Main MenuTable of Contents

251
Maintenance
Maintenance Under the Hood Changing the Engine Oil and Oil Filter
6. Check that the filter gasket is not stuck to the engine contact surface.
If it is stuck, you must detach it.
Wipe away dirt and dust adhering to the
7.
contact surface of the engine block, and install a new oil filter. Put a new washer on the drain bolt, then
8.
reinstall the drain bolt.
Tightening torque: 29 lbf∙ft (39 N∙m, 4.0 kgf∙m)
Pour the recommended engine oil into the
9.
engine.
Engine oil change capacity (including filter): 3.8 US qt (3.6 L)
Reinstall the engine oil fill cap back and
10.
start the engine. Run the engine for a few minutes, and
11.
then check that there is no leak from the drain bolt or oil filter. Stop the engine, wait for a few minutes,
12.
and then check the oil level on the engine oil dipstick.
If necessary, add more engine oil.
Oil Filter
Changing the Engine Oil and Oil Filter
You will need a special wrench to replace the oil ilter. You can buy this wrench from a dealer. When installing the new oil ilter, follow the instruction supplied with the oil ilter. Reinstall the engine oil ill cap. Start the engine. The low oil pressure indicator should go off within ive seconds. If it does not, turn off the engine, and check your work.
Main MenuTable of Contents

253
Maintenance
Maintenance Under the Hood Engine Coolant
Radiator
■
1. Make sure the engine and radiator are cool.
Turn the radiator cap counterclockwise and
2.
relieve any pressure in the cooling system. Do not press the cap down when turning. Push down and turn the radiator cap
3.
counterclockwise to remove it. The coolant level should be up to the base
4.
of the filler neck. Add coolant if it is low.
Put the radiator cap back on, and tighten it
5.
fully.Pour coolant into the reserve tank until it
6.
reaches the MAX mark. Put the cap back on the reserve tank.
Pour the fluid slowly and carefully
so you do not spill any. Clean up any spills immediately; they can damage components in the engine compartment.
Radiator
WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.Radiator Cap
Main MenuTable of Contents

266
Maintenance
Checking and Maintaining Wiper Blades
Checking Wiper Blades
If the wiper blade rubber has deteriorated, it will leaves streaks and the metal wiper arm may scratch the window glass. Changing the Front Wiper Blade Rubber1. Lift the driver side wiper arm first, then the passenger side.
2. Push the lock tab up.Slide the blade from the wiper arm.
3.
Changing the Front Wiper Blade Rubber
NOTICE When replacing a wiper blade, make sure not to drop the wiper blade or wiper arm down on the windshield.
Lock Tab
Main MenuTable of Contents

267
Maintenance
Checking and Maintaining Wiper Blades Changing the Front Wiper Blade Rubber
4. Slide the wiper blade out from its holder by pulling the tabbed end out.
5. Remove the retainer from the rubber blade that has been removed, and mount it to a new rubber blade.
Correctly align the rubber protrusion
and the retainer groove.
6. Slide the new wiper blade onto the holder from the bottom end.
The tab on the blade should fit in the
indent of the wiper blade.
Slide the wiper blade onto the wiper arm,
7.
then push down the lock tab. Lower the passenger side wiper arm first,
8.
then the driver side.
Blade
Main MenuTable of Contents

268
Maintenance
Checking and Maintaining Wiper Blades Changing the Rear Wiper Blade Rubber
Changing the Rear Wiper Blade Rubber1. Raise the wiper arm off. Slide the wiper blade out from the wiper
2.
arm while pushing the lock tab.
3. Slide the wiper blade out from its holder by pulling the tabbed end out.
4. Remove the retainer from wiper blade and mount it to a new rubber blade.Slide the wiper blade onto the holder.
5.
Make sure it is engaged correctly, then
install the wiper blade assembly onto the wiper arm.
Changing the Rear Wiper Blade Rubber
NOTICE When replacing the wiper blade, make sure not to drop the wiper blade or wiper arm down on the rear window.
Tabbed End
Main MenuTable of Contents