light HONDA CROSSTOUR 2012 1.G Technology Reference Guide

Malfunction IndicatorsIf an indicator remains on, there may be a problem; see your dealerOn\bOff Indicators
Condition IndicatorsAction is needed by driver
PASSENGER AIRBAGOFF(above Hazard Warning button)
SIDE AIRBAGOFF
VSAOFF
CRUISE CONTROL on
ECOFuel economyon
Fog lights*on
Headlightson
Turn signals/hazards on
CRUISE MAINonHigh beamson
Charging system
Low brake fluid, Brake system
Low oil pressure
ABS(anti\block brake system)
DRL(daytime running lights)
Malfunction indicator lamp(check engine light)
TPMS(tire pressure monitoring system)
VSA®(vehicle stability assist)
SRS(supplemental restraint system)
Parking brake on:
Release
Door/Tailgate open:
Close door(s) / tailgate
Seat belt reminder:
Fasten seat belt(s)
Low fuel:
Refill
Low tire pressure:
Add air
Maintenance MinderTM:
Make dealer appointment
INSTRUMENT PANEL INDICATORS
Immobilizer
Flashes: improperly coded key;
use correct key
Briefly appear with each engine start. Red and amber indicators are most critical.
Blue and green indicators are used for general information.
4\b
*if equipped
12 Crosstour TRG\fATG_NEW STYLE \b/30/2011 9\f43 AM Page 4

H O M E L I N K®( i f e q u i p p e d )
The HomeLink Universal Transceiver can be programmed to operate up to three
remote\bcontrolled devices around your home, such as garage doors, lighting, or home
security systems.
Press and hold thebutton on the
remote and the HomeLin kbutton at
the same time. Th en, while
continuing to hold the HomeLink
button, press and release thebutton
on the remote every 2seconds.
Does the LED blink at a faster rate within 20
seconds?
Press and hold
the HomeLink
button again. Training
complete
YES
NO
HomeLink indicator
flashes for 2 seconds,
then remains on. HomeLink LED
remains on.YES
NO YES
NO
Position the remote transmitter you
wish to link 1–3 inches from the
HomeLink button you want to program.1
Press and hold the desired
HomeLink button and the button on
the remote transmitter.
Does the HomeLink indicator (LED) blink at a
faster rate after about 10 seconds?
2
a
The remote has a rolling code.
Pressthe “learn” button on the
remote-controlled device (e.g.,
garage door opener).
Press the programmed HomeLink
button again; the remote-controlled
device should operate. Within 30 seconds, pressand
hold the programmed HomeLink
button for 2 seconds.a
Press and hold the programmed
HomeLink button for about a
second.
Does the device (garage door opener) work?
3
b
4
5
Training a Button
If you have any problems programming HomeLink, see the owner’s manual included
with the device you are trying to program, call HomeLink at (800) 355\b35\f5, or
visit www.homelink.com .
R E V E R S E T I L T D O O R M I R R O R S ( i f e q u i p p e d )
When you shift into Reverse (R), you can tilt either outside door mirror down slightly
to improve your view as you parallel park. Shifting out of Reverse returns the tilted
mirror to its original position.
How It Works
• To tilt the driver’s door
mirror, movethe
mirror selector switch
to the left (L) position.
• To tilt the passenger’s side door mirror, move
the mirror selector
switch to the right (R)
position.
• To turn the feature off, move the switch to the
middle position.
1011
12 Crosstour TRG\fATG_NEW STYLE \b/30/2011 9\f44 AM Page 7