crankshaft HONDA INTEGRA 1994 4.G User Guide

[x] Cancel search | Manufacturer: HONDA, Model Year: 1994, Model line: INTEGRA, Model: HONDA INTEGRA 1994 4.G
Pages: 1413, PDF Size: 37.94 MB
HONDA INTEGRA 1994 4.G User Guide INTEGRA 1994 4.G HONDA HONDA https://www.carmanualsonline.info/img/13/6067/w960_6067-0.png HONDA INTEGRA 1994 4.G User Guide
Search: (air filter, reset infotainment system, key fob battery, bluetooth, jack points, low beam)

Page 74 of 1413

HONDA INTEGRA 1994 4.G User Guide 1.Remove the cylinder head cover. . Refer to page 6-31 when installing. Remove the Dulley bolt and crankshaft pulley (see page 6-8). Remove the middle cover and the lower cover. NOTE: . Do not use the

Page 75 of 1413

HONDA INTEGRA 1994 4.G User Guide Timing Belt Installation Install the timing belt in the revorce order of removal; Only key points are described here, NOTE: Cl€an the middle cover and lower cover beforeinstallation. L Position the

Page 78 of 1413

HONDA INTEGRA 1994 4.G User Guide Gylinder Head Removal I t Engine removal is not required for this procedure. CAUTION: To avoid damaging tho cylinder head, wait until tho ongino coolant temporature drops bolow 100"F {38"C) beforo loo

Page 95 of 1413

HONDA INTEGRA 1994 4.G User Guide Cylinder Head/Valve Train 818C1 engine Special Tools ............. 6-34 wEc Troubleshooting Flowchart WEC Solenoid Valve ................... 6-36 VTEC Pressure Switch ................. 6-38 VTEC Solen

Page 105 of 1413

HONDA INTEGRA 1994 4.G User Guide Valve Clearance Adiustment NOTE: . Valves should be adjusted cold; at a cylinder head temperature of less than 100"F (38C). . Adjustmsnt is the same for intake and exhaust vatves. o After adjusting,

Page 106 of 1413

HONDA INTEGRA 1994 4.G User Guide Tightsn the locknut and recheck clearance again. Rep6at sdjustm6nt if necossary. Rotsts tha crankshaft 180 counterclockwiss (c8mshaft pulley turns 90). The "UP" mark should be on th€ sxhaust 8id6,

Page 107 of 1413

HONDA INTEGRA 1994 4.G User Guide Timing Belt . ReJerto page 6-51 for positioning crankshaft and pulley before installing belt.. Mark the direction of rotation on the belt before removing. . Replace the rubber seals for oil leakage be

Page 108 of 1413

HONDA INTEGRA 1994 4.G User Guide Grankshaft Pulley Bolt Replacement NOTE: . Crankshaft pull€y bolt size and torqus value: 1,0 x 1.25 mm 177 N.m (18.0 kgt.m, 130 lbfft) . When instslling a new crankshaft 8nd/or now pulley bolt: O t

Page 109 of 1413

HONDA INTEGRA 1994 4.G User Guide Timing Belt lnspection Remove the cylinder head cover. . Refer to page 6-78 when installing. Inspect the timing belt for cracks and oil or coolant soaking. NOTE: . Replace the belt if oil or coolant s

Page 110 of 1413

HONDA INTEGRA 1994 4.G User Guide Removal NOTE: . Turn the crankshaft pulley so the No. 1 piston is at top dead center {TDC) before removing the belt (see page 6-51). . Inspect the water pump when removed the timing belt {see page 10-
Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 60 next >
Search: (check oil, ECO mode, windshield wipers, park assist, airbag off, wiper fluid)