HUMMER H2 2004 Owners Manual

Directions and Connections Plan

All Safe and Sound Plan services
Route Support
RideAssist
Information and Convenience Services
Luxury and Leisure Plan

All Directions and Connections Plan services
Personal Concierge
OnStar®Personal Calling
As an OnStar®subscriber, the Personal Calling
capability is there for you if your hand-held cell phone is
lost, forgotten or has a low battery. It’s a hands-free
wireless phone that’s integrated into your vehicle. You
can place calls nationwide using simple voice
commands with no additional contracts and no additional
roaming charges. For more information, refer to the
OnStar
®user’s guide included with your vehicle’s
glovebox literature, visit www.onstar.com, contact
OnStar
®at 1-888-4-ONSTAR (1-888-466-7827), or
press the blue OnStar®button to speak to an OnStar®
advisor 24 hours a day, 7 days a week.
OnStar®Virtual Advisor
Virtual Advisor is a feature of OnStar®Personal Calling
that uses minutes to access up-to-date weather and
traffic reports for your area, news and sports updates,
stock quotes, entertainment and more. You are also able
to listen and reply to your e-mail through your vehicle’s
speakers. See the OnStar
®user’s guide for more
information.
OnStar®Steering Wheel Controls
g
: If your vehicle is
equipped with the steering
wheel control buttons
you can use them
to interact with the OnStar
®
system.
See the OnStar
®user’s guide for more information.
2-41

HomeLink®Transmitter
HomeLink®a combined universal transmitter and
receiver, provides a way to replace up to three
hand-held transmitters used to activate devices such as
gate operators, garage door openers, entry door
locks, security systems and home lighting. Additional
HomeLink
®information can be found on the internet at
www.homelink.com or by calling 1-800-355-3515.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of the
device.
Changes and modications to this system by other than
an authorized service facility could void authorization
to use this equipment.
Programming the HomeLink®
Transmitter
Do not use the HomeLink®Transmitter with any garage
door opener that does not have the “stop and reverse”
feature. This includes any garage door opener model
manufactured before April 1, 1982. If you have a newer
garage door opener with rolling codes, please be
sure to follow steps 6 through 8 to complete the
programming of your HomeLink
®Transmitter.
Read the instructions completely before attempting to
program the HomeLink
®Transmitter. Because of
the steps involved, it may be helpful to have another
person available to assist you in programming the
transmitter.
2-42

Keep the original transmitter for use in other vehicles as
well as for future HomeLink®programming. It is also
recommended that upon the sale of the vehicle,
the programmed HomeLink
®buttons should be erased
for security purposes. Refer to “Erasing HomeLink®
Buttons” or, for assistance, contact HomeLink®on the
internet at: www.homelink.com or by calling
1-800-355-3515.
Be sure that people and objects are clear of the garage
door or gate operator you are programming. When
programming a garage door, it is advised to park outside
of the garage.
It is recommended that a new battery be installed in
your hand-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle’s engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Press and hold down the two outside buttons,
releasing only when the indicator light begins to
ash, after 20 seconds. Do not hold down the buttons
for longer than 30 seconds and do not repeat this
step to program a second and/or third transmitter to
the remaining two HomeLink
®buttons.
2. Position the end of your hand-held transmitter
about 1 to 3 inches (3 to 8 cm) away from the
HomeLink
®buttons while keeping the indicator light
in view.3. Simultaneously press and hold both the desired
button on HomeLink
®and the hand-held transmitter
button. Do not release the buttons until Step 4
has been completed.
Some entry gates and garage door openers may
require you to substitute Step 3 with the procedure
noted in “Gate Operator and Canadian
Programming” later in this section.
4. The indicator light will ash slowly at rst and then
rapidly after HomeLink
®successfully receives the
frequency signal from the hand-held transmitter.
Release both buttons.
5. Press and hold the newly-trained HomeLink
®button
and observe the indicator light.
If the indicator light stays on constantly,
programming is complete and your device should
activate when the HomeLink
®button is pressed and
released.
To program the remaining two HomeLink
®buttons,
begin with Step 2 under “Programming HomeLink®.”
Do not repeat Step 1 as this will erase all of the
programmed channels.
If the indicator light blinks rapidly for two seconds
and then turns to a constant light, continue with
Steps 6 through 8 following to complete the
programming of a rolling-code equipped device
(most commonly, a garage door opener).
2-43

6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be found where
the hanging antenna wire is attached to the
motor-head unit.
7. Firmly press and release the “Learn” or “Smart”
button. The name and color of the button may
vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold the
programmed HomeLink
®button for two seconds,
then release. Repeat the press/hold/release
sequence a second time, and depending on the
brand of the garage door opener (or other rolling
code device), repeat this sequence a third time
to complete the programming.
HomeLink
®should now activate your rolling-code
equipped device.
To program the remaining two HomeLink
®buttons,
begin with Step 2 of “Programming HomeLink®.” Do not
repeat Step 1.
Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to “time out” or quit after several seconds of
transmission. This may not be long enough for
HomeLink
®to pick up the signal during programming.
Similarly, some U.S. gate operators are manufactured to
“time out” in the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator by using the
“Programming HomeLink
®” procedures (regardless of
where you live), replace Step 3 under “Programming
HomeLink
®” with the following:
Continue to press and hold the HomeLink
®button while
you press and release every two seconds (cycle) your
hand-held transmitter until the frequency signal has been
successfully accepted by HomeLink
®. The indicator light
will ash slowly at rst and then rapidly. Proceed with
Step 4 under “Programming HomeLink
®” to complete.
Using HomeLink®
Press and hold the appropriate HomeLink®button for at
least half of a second. The indicator light will come
on while the signal is being transmitted.
2-44

Erasing HomeLink®Buttons
To erase programming from the three buttons do the
following:
1. Press and hold down the two outside buttons until
the indicator light begins to ash, after 20 seconds.
2. Release both buttons. Do not hold for longer than
30 seconds.
HomeLink
®is now in the train (learning) mode and can
be programmed at any time beginning with Step 2
under “Programming HomeLink
®.”
Individual buttons can not be erased, but they can be
reprogrammed. See “Reprogramming a Single
HomeLink
®Button” next.
Reprogramming a Single HomeLink®
Button
To program a device to HomeLink®using a HomeLink®
button previously trained, follow these steps:
1. Press and hold the desired HomeLink
®button. Do
not release the button.
2. The indicator light will begin to ash after
20 seconds. While still holding the HomeLink
®
button, proceed with Step 2 under “Programming
HomeLink®.”
Resetting Defaults
To reset HomeLink®to default settings do the following:
1. Hold down the two outside buttons for about
20 seconds until the indicator light begins to ash.
2. Continue to hold both buttons until the HomeLink
®
indicator light turns off.
3. Release both buttons.
For questions or comments, contact HomeLink
®at
1-800-355-3515, or on the internet at
www.homelink.com.
Storage Areas
Glove Box
To open your glove box, lift up the latch and pull the
door open.
2-45

Center Overhead Console
Your vehicle is equipped with either a short or long
overhead console.
To open a door on the console, push on the rear edge
of the door and let it swing open. Push the door up
until it latches to close the door.
The overhead consoles also includes reading lamps, the
HomeLink transmitter buttons and the sunroof switch
(if equipped).
Center Console Storage Area
Your vehicle has a console compartment between the
bucket seats.
To open it, press the button on the side of the console
and swing the console lid open.
Luggage Carrier
If your vehicle has this feature, you can load cargo on
top of your vehicle.
The luggage carrier consists of siderails attached to the
roof and crossrails which can be moved back and
forth to accommodate various cargo sizes.
Notice:Loading cargo on the luggage carrier that
weighs more than 300 lbs. (136 kg) or hangs
over the rear or sides of the vehicle may damage
your vehicle. Load cargo only on top of the
crossrails and tie the cargo down to the crossrail
support cargo tie-down loops, making sure to fasten
it securely.
Don’t exceed the maximum vehicle capacity when
loading your vehicle. For more information on vehicle
capacity and loading, seeLoading Your Vehicle on
page 4-67.
2-46

Adjusting the Crossrails
Adjust the crossrails to t your load by doing the
following:
1. Loosen the lock knobs on the crossrail supports by
turning the knobs counterclockwise. Only loosen
them enough to allow the crossrails to slide easily.
2. Slide the crossrails to the desired position, being
sure to align the lines in the side rails with the
arrows on the crossrail supports.
3. Tighten the lock knobs and then try to move the
crossrails back and forth to be sure that they do
not move.4. Once you load the cargo onto the crossrails, secure
it by tying it down to the crossrail support cargo
tie-down loops. Do not load cargo directly on
the roof of your vehicle.
Be sure you do not cover the roof marker lamps or
the Center-High-Mounted Stoplamp (CHMSL) (If
equipped) with cargo.
To prevent damage or loss of cargo check now and
then to make sure the luggage and cargo are still
securely fastened and the crossrails are tight.
Stop Tabs
2-47

If your vehicle has a sunroof, it will have a crossrail stop
tab placed in the siderail in the spot labeled SUN—ROOF
STOP. This tab prevents you from moving the crossrails
past the opening of the sunroof and loading cargo too far
forward.
Your vehicle will also have a stop tab in the crossrail in
the spot labeled ON STAR STOP. This tab prevents
loading cargo too close to the OnStar antenna which will
cause the OnStar and navigation system (if equipped)
to function improperly or not at all.
Vehicles with the off-road lamps will have additional
stop tabs placed in the siderails to prevent you
from moving the lamps too far rearward, causing them
to shine into the optional sunroof opening.
Crossrail Channels
Notice:If you drive your vehicle through an
automatic car wash that does not have enough
clearance for any roof-mounted accessories (such
as off-road lamps or a roof basket) on your vehicle,
you can damage your vehicle. To avoid damaging
your vehicle in a car wash, remove any
roof-mounted accessories if you can, and do not
use an automatic car wash while roof-mounted
accessories are on your vehicle. SeeCleaning the
Outside of Your Vehicle on page 5-95for more
information.The crossrails have built in channels to allow you to
attach other items designed for this system, such
as basket luggage carriers, bike racks, ski racks, etc.
To use the crossrail channels, do the following:
1. Use the included key to unlock the crossrail end
cap by turning it counterclockwise. If you ever
loose a key, your dealer will be able to help you
obtain a replacement.
2-48

2. Pull the end cap
straight out from the
crossrail.
3. Peel back the rub strip from the crossrail.
4. Slide the accessory you are using into the crossrail
channel and secure it as the accessory instructions
direct.
5. Place the crossrail endcap back on and lock it with
the key.
You will not be using the rub strip when using crossrail
accessories. When you remove any crossrail
accessory, be sure to reinstall the rub strip. To do this,
press the rub strip in place until it seats into the
channel of the crossrail.Rear Seat Armrest
Your vehicle is equipped with a rear armrest/cupholder.
To open it, pull up and then out on the tab, located at the
top center of the armrest, and pull the armrest down.
Cargo Tie Downs
There are two cargo tie downs located on the inside of
the liftgate in the rear of the vehicle. You can use
these to secure cargo inside the vehicle with the liftgate
closed.
2-49

Sunroof
Your vehicle may be equipped with a power sliding
sunroof. To operate your sunroof, the ignition needs to
be on or RAP needs to be active. See “Retained
Accessory Power” underIgnition Positions on page 2-19.
The switch used to operate the sunroof is located in
the overhead console.The sunroof is equipped with ve positions:
First open stop:To open the sunroof and
sunshade, press and hold the rear side of the switch
until the sunroof reaches the desired position or
until it reaches the rst open stop. For more
information on using the sunshade, see “Sunshade
Operation” later in this section.
Second open stop:To open it further, press and
hold the rear side of the switch until the sunroof
reaches the desired position or until it reaches the
second open stop.
Fully open:To open the sunroof completely, press
and hold the rear side of the switch until the
sunroof opens completely.
Closed:To close the sunroof, press and hold the
front of the switch until the sunroof reaches the
desired position or until it is fully closed and stops
on its own. The sunroof will not be fully seated
unless the switch is held until the sunroof stops
moving.
2-50