engine Hyundai Accent 2006 Owner's Manual

6OWNER MAINTENANCE
20
CRANK PULLEY
G140D01A
TENSION PULLEY
A/C
AIR CONDITIONING SYSTEM MAINTENANCE
SG140C2-E Checking the Refrigerant
1. Start the engine and run at idle for
several minutes with the refrigera- tion system running at the coldest setting.
2. If the air coming out of the in-dash vents is not cold, have the air condi-tioning system inspected by your Hyundai dealer.
! CAUTION:
Running the air conditioning system for extended periods of time with a low refrigerant level may damage thecompressor.
SG140A1-E Condenser Ensure that the condenser is periodi- cally inspected and that accumulationsof dirt, dead insects and leaves etc, are removed to ensure that the efficiency of the system is not impaired. Care mustbe exercised to ensure that the con- denser fins are not damaged during cleaning.
SG140B1-E Compressor Drive Belt
0.315 in. (8mm)
The air conditioning compressor drive belt should be checked to ensure free-dom from damage or excessive wear and correct tension. The belt tension is correct when the belt deflects by about0.3 inches (8 mm) when a force of 98 N is applied to the belt halfway between the compressor and crankshaft pul-leys. Adjustment of the belt should be entrusted to a Hyundai dealer.

6
OWNER MAINTENANCE
23CHECKING DRIVE BELTS
Water Pump Pulley
Alternator Pulley
Crankshaft Pulley
HTB186
G180A01L
HXGS508 G180A01A-GAT CHECKING BRAKE PEDAL CLEARANCE
You need a helper to check the brake pedal clearance. With the engine run- ning, have your helper press down onthe brake pedal several times and then hold it down with a force of about 490 N (50 Kg, 110 lbs). The brake pedalclearance is the distance from the top surface of the brake pedal to the as- phalt sheeting under the floor mat.If the brake pedal clearance is not within the limits specified in the illustra- tion, have it inspected by your Hyundaidealer and adjusted or repaired if nec- essary. 1.78 in. (45.1 mm)
SG170A1-E BRAKE PEDAL The brake pedal freeplay should be checked with the engine turned off. Thepedal to floor clearance should be checked with the engine running and a load of 490 N applied to the pedal. Ifeither value is incorrect, the necessary adjustment should be performed by a Hyundai dealer. 0.12 ~ 0.31 in. (3 ~ 8 mm)
The various engine drive belts must be checked for condition, tension and free-dom from damage and excessive wear. The tension of a new belt must be checked after thirty minutes runningfollowing fitment of the new belt to allow for the initial belt stretch.
SG190A1-E (Petrol Engine)
0.2~0.24 in. (5.1~6 mm)

6OWNER MAINTENANCE
24
!
FUSIBLE LINKS
WARNING:
Under no circumstances should a fusible link be replaced with any- thing other than a new link of thesame rating. The use of higher rated links or other means of connecting the circuit will create a potential firehazard.
G190B01TB-GAT (Diesel Engine)
At the scheduled maintenance inspec- tion, belts should be examined forcracks, wear, fraying or other evidence of deterioration and replaced if neces- sary.Belt routing should also be checked to be sure there is no interference be- tween the belts and other parts of theengine. SG200A1-E The fusible link prevents damage to the wiring harness in the event of an elec-trical system malfunction. Failure of a fusiblelink is indicative of a serious overload condition having occurred andtherefore the electrical system should be checked by a Hyundai dealer before a replacement link is fitted.
A/C comp.
Auto tensioner Pulley
G190B01A
AlternatorPower steeringpump
G200A01A
Melted
Good

6OWNER MAINTENANCE
26ELECTRIC COOLING FANSBATTERY MAINTENANCE
!
!
o If battery electrolyte is spilled onto
skin or into eyes, the effected area must be flushed with copious amounts of water and medical assis- tance sought.
o If battery electrolyte is ingested, copious amounts of water or milkfollowed by an antacid (raw egg ormilk of magnesia) must be drunk. Vomiting should not be induced and medical assistance must be sought.
o Batteries must only be charged in well ventilated areas from which na-ked lights or sources of sparks areexcluded.
o Ensure that children, pets or other
unauthorized persons are kept awayfrom batteries.
o Do not allow anything to bridge the
positive (+) and negative (-) termi-nals of the battery.
o Never invert the battery. The battery fitted during production is of the "Maintenance Free" type.
SG210A1-E
WARNING:
Motor vehicle batteries containsulphuric acid which is corrosive and poisonous. Hydrogen gas isemitted from the battery which is explosive when combined with oxy- gen. The following precautions mustbe strictly observed to avoid per- sonal injury or damage to the ve- hicle. SG220A1-E
WARNING:
The cooling fan is controlled by en-gine coolant temperature and may sometimes operate even when the engine is not running. Use extremecaution when working near the blades of the cooling fan so that you are not injured by a rotating fanblade. As the engine coolant tem- perature decreases, the fan will auto- matically shut off. This is a normalcondition.
D010B01A
The engine cooling fan should operate before the temperature gauge reaches the upper portion of the scale and thecondenser fan should operate when- ever the air conditioning is in use.

6
OWNER MAINTENANCE
27REMOVAL OF WATER FROM THE FUEL FILTERPOWER STEERING FLUID LEVEL
G300A02B-GAT (DIESEL ENGINE)
If the fuel filter warning light illuminates during driving, it indicates that waterhas accumulated in the fuel filter. If this occurs, remove the water as described below.
SG230B1-E POWER STEERING HOSES Power steering hoses should be checked for damage, deterioration andleakage at each service.
NOTE: Grinding noise from power steering pump may be heard immediately after the engine is started in extremelycold condition (below -4°F). If the noise stops during warm up, there is no abnormal function in the system.This is due to a power steering fluid characteristic in extremely cold con- ditions. FLUID RECOMMENDATION Only automatic transmission fluid meet- ing the specification of PSF-3 or Dexron 2 should be used in the power steering system.
SG230A1-E The power steering fluid level should be checked daily.To check the power steering fluid level, be sure the ignition is "OFF", then check to make certain that the powersteering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir.
HLC5006
G300A01A

6OWNER MAINTENANCE
28HEADLIGHT AIMING ADJUSTMENT
!
1. Loosen the drain plug at the bottom
of the fuel filter.
2. Tighten the drain plug when water no longer comes out.
3. Check to be sure that the warning light illuminates when the ignition key is turned to "ON", and that it goes off when the engine is started.If in doubt, consult your nearest au- thorized HYUNDAI dealer.
NOTE: It is recommended that water accu- mulated in the fuel filter should be removed by an authorized Hyundaidealer. WARNING:
Be sure to carefully wipe away any water drained out in this manner, because the fuel mixed in the watermight be ignited and result in a fire. G290A03A-EAT Before performing aiming adjustment, make sure of the following.
1. Keep all tyres inflated to the correct
pressure.
2. Place the vehicle on level ground
and press the front bumper and rear bumper down several times. Place the vehicle at a distance of 118 in. (3,000 mm) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant,engine oil and fuel, and spare tyre,jack, and tools). Have the driver or equivalent weight placed in driver's seat.
4. Clean the head lights lens and turn on the headlight (low beam).
G300B01A

6
OWNER MAINTENANCE
29
5. Open the bonnet.
6. Draw the vertical line (through the
centre of each headlight beam pat- tern) and the horizontal line (through the centre of each headlight beam pattern) on the aiming screen. And then, draw the horizontal paral- lel line at 1.18 in. (30 mm ) under thehorizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING.
8. Adjust each cut-off line of the low beam to each vertical line with aphillips screwdriver - HORIZONTAL AIMING.
G290A01A
Horizontal Aiming
Vertical Aiming
SPECIFICATIONS: "H" Horizontal centre line of headlightsfrom ground. Petrol Engine : 25.8 in. (656 mm) Diesel Engine : 26.1 in. (664 mm) "W" Distance between each headlightcentre. Petrol Engine / Diesel Engine : 42.4 in. (1,078 mm) "L" Distance between the headlightsand the wall that the lights are tested against. : 118 in. (3,000 mm)
If the vehicle has had front body repairand the headlight assembly has been replaced, the headlight aiming should be checked using an aiming screen asshown in the illustration. Turn on the headlight switch. (Low Beam Position)
1. Adjust headlights so that main axis
of light is parallel to centre line of the body and is aligned with point "P"shown in the illustration.
2. Dotted lines in the illustration show
the centre of headlights.
G290B03A-EAT Adjustment After Headlight As- sembly Replacement
G290B01B
LW
Cut-off line Ground line
"P"
Horizontal line
Vertical line1.18 in.
H H

6OWNER MAINTENANCE
30REPLACING LIGHT BULBS
G270A03A-EAT Headlight Bulb
1. Allow the bulb to cool. Wear eyeprotection.
2. Open the engine bonnet.
3. Always grasp the bulb by its plastic
base, avoid touching the glass.
4. Using a spanner, remove the head- light assembly mounting bolts. 5. Disconnect the power cord from the
bulb base in the back of the head-light.
6. Remove the dust cover.
G260A03A-EAT In the event of bulb failure being expe- rienced, ensure that the relative lighting circuit is turned off prior to attempting to replace the bulb. The illustrations onthe following page will assist in locating and removing the various bulbs. En- sure that the replacement bulb has thesame cap configuration and wattage as the original. See page 6-34 for the wattage descrip-tions.
!
CAUTION:
Keep the lamps out of contact with petroleum products, such as oil, petrol, etc. HLC5033
HLC5009
HLC5034-1

6
OWNER MAINTENANCE
37FUSE PANEL DESCRIPTION
G200C02A-EAT Engine Compartment (Petrol Engine)
HLC5027
NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label. FUSE RATING
120A50A 50A20A30A20A 30A 30A30A30A20A 10A 10A 10A 10A10A 10A10A15A 10A15A 15A 10A 25A PROTECTED COMPONENTS
Charging (Generator) Fuse 6, 7, 8, 9, Horn fuse, Room lamp fuse
Head lamp fuse, Front fog lamp fuse, Tail lamp relay, H/LP washer fuse
Engine control relay, Generator, Fuel pump relay, ECU #3 fuse Ignition power source, Start relayRadiator fan control Blower control ABS control, ABS bleeding connectorABS control, ABS bleeding connector Power window Condenser fan controlRadiator fan, Condenser fan, ECM, Oxygen sensor, Purge control valve,
SMATRA, Glow plug relay, Heater relay, Stop lamp switch A/C relayHorn relay Illumination lamps, Left rear combination lamp, License lamp, DRL control, Position lamp, H/LP washer relayRight rear combination lamp, License lamp, Position lamp Left head lamp, DRL control, Instrument cluster Right head lampFront fog lamp relay
Instrument cluster, Courtesy lamp, Trunk room lamp, ETACM, DLC, Door warning, Multipurpose check connectorAudio, Digital clock, Power antenna, A/C switch, Rear fog lamp switch Idle speed actuator, ECM, Camshaft position sensor, EGR actuator, Throttle plate actuatorECM Head lamp washer motor
Fuel pump relay, Fuel pump motor
ALT
BATTERY LAMPECU
IGN
RAD FAN
BLOWER
ABS ABS
P/WDW
COND FAN
ECU #1
A/CON COMP HORN
TAIL LH
TAIL RH
H/LP LH
H/LP RH
FRONT FOG
ROOM LP AUDIO
ECU #2 ECU#3
H/L WASHER
FUSIBLE
LINK
FUSE
DESCRIPTION
F/PUMP CHK (E50)

6OWNER MAINTENANCE
38
PROTECTED COMPONENTS
Charging (Generator) Fuse 6, 7, 8, 9, Horn fuse, Room lamp fuse
Head lamp fuse, Front fog lamp fuse, Tail lamp relay, H/LP washer fuse
Engine control relay, Generator, Fuel pump relay, ECU #3 fuseIgnition power source, Start relayRadiator fan controlBlower controlABS control, ABS bleeding connectorABS control, ABS bleeding connectorPower windowCondenser fan controlAssist HeaterAssist HeaterGlow Plug relayFuel HeaterRadiator fan, Condenser fan, ECM, Oxygen sensor, Purge control valve,
SMATRA, Glow plug relay, Heater relay, Stop lamp switchA/C relayHorn relayIllumination lamps, Left rear combination lamp, License lamp, DRL control,Position lamp, H/LP washer relayRight rear combination lamp, License lamp, Position lampLeft head lamp, DRL control, Instrument clusterRight head lampFront fog lamp relay
Instrument cluster, Cour tesy lamp, Trunk room lamp, ETACM, DLC,Door warning, Multipurpose check connectorAudio, Digital clock, Power antenna, A/C switch, Rear fog lamp switchIdle speed actuator, ECM, Camshaft position sensor, EGR actuator,Throttle plate actuatorECMHead lamp washer motor
Fuel pump relay, Fuel pump motor
HLC5026 FUSE RATING
120A
50A50A30A30A20A30A30A30A30A20A60A30A80A30A 10A10A 10A 10A10A 10A10A15A 10A15A15A10A 25A
ALT
BATTERY
LAMP
ECU (DSL)
IGN
RAD FAN
BLOWER ABS ABS
P/WDW
COND FAN HTRHTR
GLOW F/HTR
ECU #1
A/CON COMP HORN
TAIL LH
TAIL RH
H/LP LH
H/LP RH
FRONT FOG
ROOM LP
AUDIO
ECU #2 ECU#3
H/L WASHER
FUSIBLE
LINK
FUSEDESCRIPTION
F/PUMP CHK (E50)G200D02A-GAT Engine Compartment (Diesel Engine)