front shield Hyundai Equus 2016 User Guide

3-128
Convenient features of your vehicle
Front button
The mode selection button controls
the air flow direction from the ventila-
tion system.The air flow outlet can be converted
as follows:
Face-Level (B, D, F, G)
Air flow is directed toward the upper
body and face. Additionally, each air
outlet port can be controlled and
directed manually.
Bi-Level (B, C, D, E, F, G, H)
Air flow is directed toward the face
and the floor.
Floor & Defrost
(A, C, E, D, G, H)
Most of the air flow is directed to the
floor and the windshield, while a
small amount of the air flow is direct-
ed to the side window defrosters.
Floor-Level (A, C, E, D, G, H)
Most of the air flow is directed to the
floor, while a small amount of the air
flow is directed to the windshield and
side window defrosters.
OVI045115N
■
Front
OVI045403N
■
Rear - Type A
OVI045416N
■
Rear - Type B

3-129
Convenient features of your vehicle03
Rear button
If you press the rear button, the 3
ZONE indicator will illuminate, and
you can adjust the rear mode individ-
ually. If you press the 3 ZONE button,
the 3 zone control indicator will be
turned OFF, and the rear mode will
be operated as the front mode.
The air flow outlet can be converted
as follows:
Face-level (G)
Air flow is directed toward the upper
body and face.
Bi-level (G, H)
Air flow is directed toward the face
and floor.
Floor level (G, H)
Air flow is directed toward the floor.
Information
When the front windshield defrost
button is pressed, the rear air flow will
be blocked.
Defrost-Level (A)
Most of the air flow is directed to the
windshield with a small amount of air
directed to the side window defrosters.
Instrument panel outlet
The outlets can be opened or closed
separately using the thumbwheel. To
close the outlet, rotate it in a counter-
clock-wise direction. To open the out-
let, rotate it in a clock-wise direction.
Also, you can adjust the air flow
direction from these outlets using the
vent control lever as shown.
i
OVI045112N
OVI045113N

3-135
Convenient features of your vehicle03
System operation
Ventilation
1. Set in the mode.
2. Set the air intake control in the(fresh) air intake mode.
3. Set the temperature, as desired.
4. Set the fan speed, as desired.
Heating
1. Set in the mode.
2. Set the air intake control in the (fresh) air intake mode.
3. Set the temperature, as desired.
4. Set the fan speed, as desired.
5. In order to get dehumidified heat- ing, turn ON the A/C.
If the windshield is fogged up, set in the mode or press the front
defrost button .
Operation Tips
To keep dust or unpleasant fumesfrom entering the vehicle through
the ventilation system, temporarily
set the air intake control in the air
recirculation mode. Make sure to
return to be in the (fresh) air intake
mode when the irritating dust and
gas fade away and the fresh air
intake is possible. This will keep
the driver alert and comfortable.
Air needed for the heating/cooling system is taken inside through the
grilles in front of the windshield.
Care should be taken that these
are not blocked by leaves, snow,
ice or other substances. To prevent fogging on the inside of
the windshield, set the air intake
control in the (fresh) air intake
mode, set the fan speed as
desired, turn ON the A/C, and
adjust the temperature as desired.
Air conditioning
1. Start the engine. Press the A/Cbutton.
2. Set in the mode.
3. Set the air intake control either in the (fresh) air intake mode or in
the air recirculation mode.
4. Adjust the fan speed and tempera- ture for your greatest comfort.
Information
• When using the A/C system, closelymonitor the engine temperature
gauge while driving up hills or in
heavy traffic when the outside tem-
perature is high. A/C operation may
overheat the engine. Continuously
use the blower fan. However, turn
the air conditioning system OFF if
the engine temperature gauge indi-
cates engine overheating.
• When opening the windows in humid weather, A/C operation may
create dew condensation inside the
vehicle. Since excessive dew conden-
sation may cause damage to electri-
cal equipment, A/C should be oper-
ated only with the windows closed.
i

3-140
Convenient features of your vehicle
Auto defogging system (if equipped)
Auto defogging reduces the probabil-
ity of the dew condensation on the
inside of the windshield by automati-
cally sensing the moisture.
The auto defogging system operates
when the heater or the A/C is ON.
This indicator illuminates
when the auto defogging
system senses the mois-
ture on the inside of the
windshield and operates.
If it is humid inside the vehicle, the
automated steps operate as follows:
If auto defogging system does not
defog the window in the step 1 (fresh
air intake mode), the steps 2 and 3
will be followed.
Step 1 : (fresh) air intake mode
Step 2 : Operating the A/C
Step 3 : Blowing air toward the wind- shield
Step 4 : Increasing air flow toward the windshield The auto defogging system automat-
ically activates in certain conditions.
However, if you want to turn OFF the
auto defogging system, press the
front defroster button 4 times within 2
seconds while pressing the AUTO
button. The front defroster indicator
will flash 3 times to notify the system
cancellation. To restart the auto
defogging system, follow the proce-
dures mentioned above.
If the battery is disconnected or dis-
charged, it resets to the auto defog-
ging status.Information
When the A/C is turned ON and the
(fresh) air intake mode is selected by
the auto defogging system, and when
you try to turn OFF the A/C and select
the air recirculation mode, the indica-
tor will just flash 3 times, the A/C will
not be turned OFF, and the air recir-
culation mode will not be selected.
Do not remove the sensor cover
on the upper end of the driver's
side windshield. Damage to sys-
tem parts could occur and may
not be covered by your vehicle
warranty.
NOTICE
i
OVI045109N

5-4
Driving your vehicle
- ENGINE EXHAUST CAN BE DANGEROUS!
Engine exhaust fumes may be extremely dangerous. When, at any time, you
smell exhaust fumes inside the vehicle, immediately open the windows.
• Do not inhale exhaust fumes.Exhaust fumes contain carbon monoxide, the colorless, odorless gas that
may cause unconsciousness and death by asphyxiation.
The exhaust system should be checked whenever the vehicle is raised to
change the oil or for any other purpose. If you notice a change in the sound
of the exhaust system or if you drive over something that strikes the vehicle
underneath, have the exhaust system checked as soon as possible by an
authorized EQUUS dealer.
Letting the engine idle in a garage, even with the garage door open, is haz-
ardous. Never run the engine in your garage any longer than it takes to start
the engine and move out the vehicle.
Avoid idling the engine for a prolonged period of time with people inside the vehicle.
If it is necessary to idle the engine for a prolonged period of time with people
inside the vehicle, idle the engine in an open area with the air control in the
(fresh) air intake mode and the fan operating at a high speed. Thus, fresh air
can be taken into the interior.
When you need to drive with the trunk lid open because of the object you carry,
make sure the followings:
1. Close all windows.
2. Open side vents.
3. Set the air intake control in (fresh) air intake mode, the air flow directed toward "Floor" or "Face," and the fan at a high speed.
To assure proper ventilation, clear snow, ice, leaves or other substances from
the air inlet just in front of the windshield.
WARNING
Engine exhaust and a wide variety of automobile components and
parts, including components found in the interior furnishings in a
vehicle, contain or emit chemicals known to the State of California to
cause cancer and birth defects and reproductive harm. In addition,
certain fluids contained in vehicles and certain products of compo-
nent wear contain or emit chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm.
California PROPOSITION 65 WARNING

This system detects lane lines with
the sensor located on the front wind-
shield, and warns the driver of driv-
ing out of lane lines (lane departure).
L LA
A N
N E
E
D
D E
EP
P A
A R
RT
TU
U R
RE
E
W
W A
AR
RN
N I
IN
N G
G
S
S Y
Y S
ST
T E
EM
M
(
( L
L D
D W
W S
S)
)
(
( I
IF
F
E
E Q
Q U
UI
IP
P P
PE
ED
D )
)
5-51
Driving your vehicle05
OVI055012N
OVI055013N
The LDWS does not automati-
cally control the driving direc-
tion. It is the driver's responsi-
bility to always check the road
conditions.
Do not abruptly turn the steer- ing wheel, upon getting the
LDWS warnings.
(Continued)
(Continued)
When the sensor cannotdetect lane lines, or when the
vehicle speed does not
exceed 43 mph (70 km/h), the
LDWS warnings will not be
given, even while driving out
of lane lines.
When the front windshield is tinted or coated, the LDWS
may not properly operate.
Keep the LDWS sensor off water or any liquid to prevent
damage.
Do not disassemble the LDWS, nor damage the sensor
with a strong impact.
Do not put reflective objects on the dash board.
Always check the road condi- tions, as you may not hear the
warning alarm due to audio or
other external noises.
WARNING

DRIVER'S ATTENTION
The driver must be cautious in the
below situations, because the sys-
tem may not assist the driver nor
work properly.
The lane is not visible due tosnow, rain, stain, puddles or oth-
ers.
The exterior brightness sudden- ly changes, such as driving
through a tunnel.
The headlamp is turned OFF or weak in the night time or in a
tunnel.
It is difficult to distinguish the lane mark colors from the road.
The vehicle drives on a steep slope or a curve.
Lights, such as sunlight, street- light or lights from other vehi-
cles, reflect from the water on
the road.
The lens or windshield is stained with foreign substances.
The sensor cannot detect the lane lines because of fog, heavy
rain or heavy snow.
The surrounding temperature of the inside rear view mirror is
extremely high due to direct
sunlight.
The lane is very wide or narrow.
The lane mark is damaged or indistinct.
The shadow of median strips cast on the lane marks.
There are similar marks to lane marks.
There is a boundary structure.
The distance from a vehicle in front is very short. So, its driving
hides the lane marks in front.
(Continued)(Continued)
The vehicle is violently shaken.
The number of lane marks
increases or decreases, or the
lane marks cross each other in a
complicated manner.
Something is placed on the dashboard.
The vehicle drives against sun- light.
The vehicle drives in a construc- tion area.
There are more than two lane marks.
The lane marks are hard to be distinguished due to dust or
grease in a tunnel.
The lane marks are hard to be distinguished after raining at
night.
The lane marks are hard to be distinguished due to dust.
5-54
Driving your vehicle

5-69
Driving your vehicle05
Smooth cornering
Avoid braking or shifting a gear on a
corner, especially when a road sur-
face is wet. It is ideal to drive a cor-
ner by gently accelerating. When you
take this suggestion, the tire wear-
out will be minimized.
Driving at night
Since night-time driving is more haz-
ardous than day-time driving, here
are some important tips to remem-
ber:
Slow down a driving speed andkeep a longer safe distance from a
vehicle in front, as it may be hard-
er to see at night, especially in
areas without any street lights.
Adjust your mirror angle to reduce glares from the headlamps of other
vehicles.
Keep your headlamps clean and properly aimed at. Any foreign sub-
stances on a headlamp and an
improperly adjusted headlamp
angle make it much harder to see
at night. Turning the headlamp ON,
while operating windshield wipers,
is mandatory in some states.
Avoid directly staring at the head- lamps of approaching vehicles.
This may temporarily blind your
vision, and take several seconds
for your eyes to readjust in the
darkness.
OVI055209NOVI055210N

7-36
Maintenance
Blade inspectionInformation
Hot wax in market may be used in
automatic car washes. However, it is
known to make it difficult to clean the
windshield.
Contamination of either the wind-
shield or the wiper blades with for-
eign substances may undermine the
effects of the windshield wipers.
Common contamination sources are
insects, tree sap, and hot wax treat-
ments used in some car washes.
When the blades do not properly
wipe off, clean the window and
blades with a good-quality cleaner or
mild detergent. Then, thoroughly
wash them with clean water.
Do not use gasolines, kerosene,
paint thinner, or other solvents on
or near the wiper blades to pre-
vent damage.
Blade replacement
When the wipers no longer ade-
quately clean, the blades may be
worn out or cracked. Then, replace-
ment is required.
To prevent damage to the wiper
arms or other components, do not
attempt to manually move the
wipers.
The use of a non-specified wiper
blade could result in wiper mal-
function and failure.
Front windshield wiper blade
For your convenience, move the
windshield wiper blades as illustrat-
ed.
Turn off the engine.
Fully raise the wipers by setting the
wiper lever in the single wiping
(MIST) position less than 20 sec-
onds.
NOTICE
NOTICE
NOTICE
i
W WI
IP
P E
ER
R
B
B L
LA
A D
DE
ES
S

OVI075164N
OVI075041N

The vehicle identification number
(VIN) is the number used in register-
ing your vehicle and in dealing with
all legal matters, such as ownership.
The number is punched on the floor
under the front passenger’s seat. To
check the number, open the cover.
The VIN is also on a plate attached
to the top of the dashboard. The
number on the plate can easily be
seen through the windshield from
outside.The vehicle certification label
attached on the driver’s side center
pillar has the vehicle identification
number (VIN).
T T
I
IR
R E
E
S
S P
P E
EC
CI
IF
F I
IC
C A
A T
TI
IO
O N
N
A
A N
N D
D
P
P R
R E
ES
SS
SU
U R
RE
E
L
L A
A B
BE
EL
L
The tires, equipped with your new
vehicle, are chosen to provide the
best performance in a normal driving
condition.
The tire label, located on the driver's
side center pillar, gives the tire infor-
mation, such as the recommended
pressure.
8-6
Specifications, Consumer information and Reporting safety defects
OVI085001N
OVI085005N
Frame number
VIN label
V
V E
EH
H I
IC
C L
LE
E
C
C E
E R
R T
TI
IF
F I
IC
C A
A T
TI
IO
O N
N
L
L A
A B
BE
EL
L
V
V
E
EH
H I
IC
C L
LE
E
I
ID
D E
EN
N T
TI
IF
F I
IC
C A
A T
TI
IO
O N
N
N
N U
U M
M B
BE
ER
R
(
( V
V I
IN
N )
)
OVI085002N
OVI085006N