key Hyundai Getz 2004 Workshop Manual

FEATURES OF YOUR HYUNDAI 1- 11
!
HTB024-D
B080A01FC-EAT
SEAT ADJUSTMENT
B080B02FC-EAT
FRONT SEATS
Front Seat Rake Adjustment
The front seat rake adjustment is per-
formed by raising the lever at the front
of the seat base and sliding the seat to
the desired position. At this position the
lever should be released and the seat
rocked to and fro to ensure that the
mechanism has locked.
WARNING:
Front seat adjustments must not be
undertaken whilst the vehicle is in
motion. Loss of control of the ve-
hicle may result if seat adjustments
are made whilst the vehicle is in
motion.
WARNING:
1) Be careful that someone's head, hands and body are not trapped
by a closing window.
2) Never try to operate the main switch on the driver's door and
the individual door window switch
in opposing directions at the same
time. If this is done, the window
will stop and cannot be opened or
closed.
3) Do not leave children alone in the
car. Always remove the ignition
key for their safety.
!
!WARNING:
To ensure the seat is locked se-
curely, attempt to move the seat for-
ward or rearward without using the
lever.
tbuk-1a.p65 3/23/04, 2:21 PM
11

FEATURES OF YOUR HYUNDAI 1- 29
!
o Although it is harmless, the fine
dust may cause skin irritation and
should not be breathed for pro-
longed periods. Wash your hands
and face thoroughly after an acci-
dent in which the pre-tensioner
seat belts were activated. it illuminates whilst the vehicle is
being driven, please have an au-
thorized Hyundai dealer inspect
the pre-tensioner seat belt or SRS
airbag system as soon as pos-
sible.
CAUTION:
o Because the sensor that activates the SRS airbag is connected with
the pre-tensioner seat belt, the SRS
airbag warning light on the
instrument panel will blink for
approximately 6 seconds after the
ignition key has been turned to the
"ON" position and then it should
turn off.
o If the pre-tensioner seat belt is not working properly, this warning
light will illuminate even if there is
no function of the SRS airbag sys-
tem.
If the SRS airbag warning light
does not illuminate when the igni-
tion key is turned to "ON", or if it
remains illuminated after blinking
for approximately 6 seconds, or if WARNING:
o Pre-tensioners are designed to op- erate only one time. After activa-
tion, pre-tensioner seat belts must
be replaced. All seat belts, of any
type, should always be replaced
after they have been worn during a
collision.
o The pre-tensioner seat belt assem-
bly mechanisms become hot dur-
ing activation. Do not touch the
pre-tensioner seat belt assemblies
for several minutes after they have
been activated.
o Do not attempt to inspect or re-
place the pre-tensioner seat belts
yourself. This must be done by an
authorized Hyundai dealer.
o Do not strike the pre-tensioner seat
belt assemblies.
!
!WARNING:
To obtain maximum benefit from a
pre-tensioner seat belt:
1. The seat belt must be worn cor- rectly.
2. The seat belt must be adjusted to the correct position.
NOTE:
o Both the driver's and front passenger's pre-tensioner seat
belts will be activated in certain
frontal collisions. The pre-
tensioner seat belts can be acti-
vated with the airbags. The pre-
tensioners will be activated under
these conditions even if the seat
belts are not being worn at the
time of the collision.
o When the pre-tensioner seat belts
are activated, a loud noise may be
heard and fine dust, which may
appear to be smoke, may be vis-
ible in the passenger compart-
ment. These are normal operating
conditions and are not hazard-
ous.
tbuk-1a.p65 3/23/04, 2:22 PM
29

1- 32 FEATURES OF YOUR HYUNDAI
B240B03L-D
The airbag modules are located both in
the centre of the steering wheel and in
the front passenger's panel above the
glove box. When the SRSCM detects a
considerable impact to the front of the
vehicle, it will automatically deploy the
airbags.
Passenger's Airbag
HTB204-D
Upon deployment, tear seams molded
directly into the pad covers will sepa-
rate under pressure from the expansion
of the airbags. Further opening of the
covers then allows full inflation of the
airbags.
A fully inflated airbag in combination
with a properly worn seat belt slows the
driver's or the passenger's forward mo-
tion, thus reducing the risk of head or
chest injury.
The SRS service reminder indicator
(SRI) on the instrument panel will blink
for about 6 seconds after the ignition
key is turned to the "ON" position or
after the engine is started, after which
the SRI should go out.
B240B02L-D
tbuk-1a.p65
3/23/04, 2:22 PM
32

FEATURES OF YOUR HYUNDAI 1- 33
!
!
CAUTION:
When installing a container of liquid
air freshener inside a vehicle, do not
place it near the instrument cluster
nor on the instrument panel pad
surface. If there is any leakage from
the air freshener onto these areas
(instrument cluster, instrument panel
pad or air ventilator), it may damage
these parts. If the liquid from the air
freshener does leak onto these ar-
eas, wash them with water immedi-
ately.
WARNING:
o When the SRS is activated, there may be a loud noise and fine dust
will be released throughout the
vehicle. These conditions are nor-
mal and are not hazardous. How-
ever, the fine dust generated dur-
ing airbag deployment may cause
skin irritation. Be sure to wash
your hands and face thoroughly
with lukewarm water and a mild
soap after an accident in which
the airbags were deployed. o The SRS can function only when
the ignition key is in the "ON"
position. If the SRS SRI does not
come on, or continuously remains
on, after flashing for about 6 sec-
onds when the ignition key is
turned to the "ON" position, or
after the engine is started, or comes
on while driving, the SRS is not
working properly. If this occurs,
have your vehicle immediately
inspected by your Hyundai dealer.
o Before you replace a fuse or dis-
connect a battery terminal, turn
the ignition key to the "LOCK"
position or remove the ignition
key. Never remove or replace the
air bag related fuse(s) when the
ignition key is in the "ON" posi-
tion. Failure to heed this warning
will cause the SRS SRI to illumi-
nate.
B240B05L-D
Passenger's Airbag
!
CAUTION:
Do not install or place any accesso-
ries (drink holder, cassette holder,
sticker, etc) on the front passenger's
panel above the glove box in a ve-
hicle with passenger's side air bag.
Such objects may become danger-
ous projectiles and cause injury if
the passenger's side air bag inflates.
After complete inflation, the airbag im-
mediately starts deflating, enabling the
driver to maintain forward visibility.
tbuk-1a.p65 3/23/04, 2:22 PM
33

FEATURES OF YOUR HYUNDAI 1- 35
!
B240C02L WARNING:
o Do not install a child restraint system in the front passenger
seat position.
A child restraint system must
never be placed in the front seat.
The infant or child could be se-
verely injured by an airbag de-
ployment in case of an accident.
o Extreme Hazard! Do not use a rear-
ward facing restraint on a seat
protected by an airbag in front of
it!
o Modification to SRS components or wiring, including the addition
of any kind of badges to the pad
covers or modifications to the
body structure, can adversely
affect SRS performance and lead
to possible injury.
o For cleaning the airbag pad cov-
ers, use only a soft, dry cloth or
one which has been moistened
with plain water. Solvents or
cleaners could adversely affect the
airbag covers and proper deploy-
ment of the system.
B240C02Y-GAT
SRS Care
The SRS is virtually maintenance-free
and there are no parts you can safely
service by yourself. The entire SRS
system must be inspected by an au-
thorized Hyundai dealer in 10 years
after the date that the vehicle was
manufactured.
Any work on the SRS system, such as
removing, installing, repairing, or any
work on the steering wheel must be
performed by a qualified Hyundai tech-
nician. Improper handling of the SRS
system may result in serious personal
injury.
o Do not place any objects (an um-
brella, bag, etc.) between the front
door and the front seat. Such ob-
jects may become dangerous pro-
jectiles and cause injury if the
supplemental side impact air bag
inflates.
o To prevent unexpected deploy- ment of the side air impact bag
that may result in personal injury,
avoid impact to the side airbag
sensor when the ignition key is
on.
tbuk-1a.p65 3/23/04, 2:22 PM
35

FEATURES OF YOUR HYUNDAI 1- 39
SB210C1-F
SRS (Airbag) SERVICE
REMINDER INDICATOR
The SRS service reminder indicator
(SRI) comes on and flashes for about 6
seconds after the ignition key is turned
to the "ON" position or after the engine
is started, after which it will go out.
This light also comes on when the SRS
is not working properly.
If the SRI does not come on, or continu-
ously remains on after flashing for about
6 seconds when you turned the ignition
key to the "ON" position or started the
engine, or if it comes on while driving,
have the SRS inspected by an autho-
rized Hyundai Dealer. B260P02Y-EAT
ABS SERVICE
REMINDER INDICATOR
(SRI) (Not all models)
When the key is turned to the "ON"
position, the Anti-Lock Brake System
SRI will come on and then go off in a few
seconds. If the ABS SRI remains on,
comes on while driving, or does not
come on when the key is turned to the
"ON" position, this indicates that there
may be a problem with the ABS.
If this occurs, have your vehicle
checked by your Hyundai dealer as
soon as possible. The normal braking
system will still be operational, but
without the assistance of the anti-lock
brake system. SB210E1-E
OVERDRIVE OFF INDI
CATORLIGHT
(Not all models)
When the overdrive (4th gear) switch is
turned off and the operation of overdrive
(4th gear) is cancelled, the overdrive
warning light (O/D OFF) will be illumi-
nated. When the switch is at the on
position, the gearbox will operate in the
normal fully automatic mode and the
warning light will be extinguished.
SB210G1-E TURN SIGNAL
INDICATOR LIGHT
Operation of a turn signal is indicated
by the warning light located in the in-
strument cluster. If the light fails to
illuminate or does not flash, a malfunc-
tion within the turn signal system is
indicated.
! WARNING:
If the both ABS SRI and Parking
Brake/Brake fluid level warning lights
remain "ON" or come on while driv-
ing, there may be a problem with
E.B.D (Electronic brake force distri-
bution).
If this occurs, avoid sudden stops
and have your vehicle checked by
your Hyundai dealer as soon as pos-
sible.
tbuk-1a.p65 3/23/04, 2:22 PM
39

FEATURES OF YOUR HYUNDAI 1- 41
SB210M1-E
CHARGING SYSTEM
WARNING LIGHT
The charging system warning light
should illuminate when the ignition
switch is turned to the "ON" position
and should be extinguished when the
engine is started. If the light fails to
illuminate when the ignition is turned
"ON" or fails to extinguish after starting
the engine, the nearest Hyundai dealer
should be contacted. If the light illumi-
nates whilst the vehicle is being driven,
stop the vehicle as soon as it is safe to
do so and check the condition of the
generator drive belt. If the belt is in SB2100I-E
DOOR AJAR WARNING
LIGHT
The door ajar warning light indicates
that a door is not correctly closed.
Ensure that the light is extinguished
prior to driving the vehicle.
B260B01FC-EAT
TAIL GATE OPEN
WARNING LIGHT
The tail gate warning light indicates
when the tail gate is open or is not fully
closed. Ensure that the light has extin-
guished prior to driving the vehicle. SB210P1-E
LOW FUEL LEVEL
WARNING LIGHT
The low fuel warning light serves to
warn the driver that the remaining fuel
quantity is approximately 9 litres and
that the vehicle should be refuelled. If
the vehicle is driven for an extended
period with the low fuel warning light
illuminated there exists a possibility
that misfiring due to fuel shortage may
occur. This situation must be avoided
to prevent damage to the catalyst oc-
curring.
recommended to assist in bringing the
vehicle to rest. The vehicle must not be
driven once brake failure has occurred
until the system has been repaired and
is functioning normally.
The braking system employs a vacuum
servo in order that the pedal efforts are
reduced. Power for the servo is derived
from the engine and therefore, in the
event of the engine stopping or the
vehicle being towed, pedal efforts will
be substantially increased.
place and the tension is satisfactory,
the advice of a Hyundai dealer should
be sought.
CAUTION:
If the drive belt (generator belt) is
loose, broken, or missing while the
vehicle is driving, there may be a
serious malfunction, engine could
overheat because this belt also drives
the water pump.
!
B260N02FC-EAT MALFUNCTION INDICA-
TOR LIGHT
This light illuminates when there is a
malfunction of an exhaust gas related
component, and the system is not func-
tioning properly so that the exhaust gas
regulation values are not satisfied. This
light will illuminate when the ignition key
is tuned to the "ON" position, and will go
out after the engine start. If it illumi-
nates while driving, or does not illumi-
nate when the ignition key is turned to
the "ON" position, take your car to your
tbuk-1a.p65 3/23/04, 2:22 PM
41

1- 42 FEATURES OF YOUR HYUNDAI
B260S01B-GAT
DIESEL PRE-HEAT
INDICATOR
LIGHT-AMBER
(Diesel Engine)
The indicator light illuminates amber
when the ignition switch is placed at
the "ON" position. The engine can be
started after the pre-heat indicator light
goes off. The illuminating time varies
with the water temperature, air tem-
perature and battery condition.
NOTE:
If the engine were not started 10
seconds after the preheating is com-
pleted, turn the ignition key once
more to the "LOCK" position, and
then to the "ON" position, in order
to preheat again.
B260T01TB-GAT
ELECTRIC POWER
STEERING SYSTEM
(EPS) WARNING LIGHT
(Not all models)
This indicator light comes on about 4
seconds after the ignition key is turned
to the "ON" position or after the engine
is started, it will go out.
This light also comes on when the EPS
has some troubles. If it comes on while
driving, have your vehicle inspected by
an authorized Hyundai Dealer. B260E01HP-GAT
SEAT BELT WARNING
LIGHT
The seat belt warning light blinks for
about 6 seconds when the ignition key
is turned from the "OFF" position to
"ON" or "START".
CAUTION:
When you move the electric power
steering back-end and forth-end
continuously in stop position, steer-
ing wheel plays heavily to operate
anti-overload system. It is normal
condition. It returns to be nomal
getting time.!
B260U01TB-EAT IMMOBILIZER
INDICATOR LIGHT
(Not all models)
This indicator light comes on for some
seconds after the ignition key is turned
to the "ON" position. At this time, you
can start the engine. The light goes out
after the engine is running. In case this
light goes out before you start the en-
gine, you must turn to the "LOCK"
position and restart the engine. In case
this light blinks for five seconds when
the ignition key is turned to "ON" posi-
tion, this indicates that the immobilizer
system is out of order. At this time,
consult to the Hyundai dealer.
nearest authorized Hyundai dealer and
have the system checked.
tbuk-1a.p65
3/23/04, 2:22 PM
42

FEATURES OF YOUR HYUNDAI 1- 49
HTB017-DHTB015-D
B340C03FC-EAT
LIGHTING SWITCH
The vehicle side lights and headlights
are operated by rotating the end of the
turn signal switch barrel. To operate the
side lights, rotating the switch to the
first detent with ignition switch at the
"OFF" position will cause the lights to
illuminate. To operate the headlights,
the turn signal switch barrel should be
rotated to the second detent. The head-
lights will only operate when the ignition
switch is at the "On" position. If the
ignition switch is turned to the "Off"
position, only the side lights will func-
tion.
NOTE:
The ignition must be in the "ON"
position to turn on the headlights. Side light auto cut
(Not all models)
If you do not turn the side lights "OFF"
after driving, the side light will automati-
cally shut "OFF" when the driver's door
is opened.
To turn them "ON" again you must
simply turn the ignition key to the "ON"
position.
SB220D1-E
HIGH AND LOW BEAM
To turn on the headlight high beams,
push the lever forward (away from you).
For low beams, pull the lever back
(toward you). The appropriate headlight
beam indicator light will come on at the
same time.
SB220E1-E
HEADLIGHT FLASH
The headlights may be flashed by pull-
ing the turn signal switch lever towards
the steering wheel. The headlights will
be extinguished when the switch is
released.
tbuk-1a.p65
3/23/04, 2:22 PM
49

FEATURES OF YOUR HYUNDAI 1- 53
SB290A02-F
CIGAR LIGHTER
For the cigar lighter to work, the key
must be in the "ACC" or the "ON"
position.
To use the cigar lighter, push the lighter
all the way into its socket. When the
element is heated, the lighter will pop
out into the "ready" position.
Do not hold the cigar lighter at the
depressed position which may result in
damage to the vehicle wiring or an
electrical fire.
HTB097
B400A01TB-AAT
DIGITAL CLOCK HTB095
There is a digital clock control button
built-in right side of the speedometer.
Its functions are:
o Reset : Push the button for more than
1 second.
o Min/Hour Adjustment: Turn to "H"
for 0.5 second to advance the hour
indicated. Turn to "M" for 0.5 sec-
ond to advance the minute indi-
cated.
o Auto mode: Turn to the right or left
side for more than 1 second to ad-
vance fastly. CAUTION:
Don't turn the switch excessively to
prevent switch damage.
!
B360A01Y-GAT
REAR FOG LIGHT SWITCH
To turn on the rear fog lights, push the
switch. They will come on when the
headlight switch is in the second posi-
tion and the key is in the "ON" position. HTB096
tbuk-1a.p65
3/23/04, 2:22 PM
53