oil filter Hyundai Matrix 2007 Owner's Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2007, Model line: Matrix, Model: Hyundai Matrix 2007Pages: 490, PDF Size: 12.81 MB
Page 438 of 490

6 OWNER MAINTENANCE
10
G040B04FC-EAT
Diesel engine
Oil filter
G040B01FC
Oil filler cap
Centrepipe O-ring G040B02FC
Upper capO-ring
Oil filter element
Oil filterhousing
The engine oil and filter should be
changed at those intervals specified in the maintenance schedule in Section 5. If the car is being driven in severe conditions, more frequent oil and filter changes are required.
The procedure for changing the oil and
filter is as follows:
1. Park the car on level ground and set the parking brake. Start the engine and let it warm up until the needle on the coolant temperature gauge moves above the lowest mark. Turn the engine off and place the gear selector lever in "P" (automatic) or reverse gear (manual transaxle). 2. Open the bonnet and remove the
engine oil level dipstick.
3. Loosen the oil filter upper cap with a proper tool from the oil filter housing until an O-ring is seen. Then, drainthe oil completely.
CAUTION:
Slowly loosen the oil filter uppercap not to overflow the oil.
!
!
CAUTION:
Slowly pour the recommended oil into a funnel. Do not overfill to prevent engine to damage.!
WARNING:
Prolonged and repeated contact with used engine oils may result in seri- ous skin disorders including der- matitis and cancer. Avoid contact with skin as far as possible andalways wash thoroughly after any contact. Keep used oils out of reach of children. It is illegal to pollutedrains, water courses and soil. Use only authorized waste collection facilities including civic amenitysites and garages for the disposal of used oil and oil filters. If in doubt, contact the local authority for dis-posal instructions.
fcuk-6.p65 12/27/2006, 10:16 AM
10
Page 439 of 490

6
OWNER MAINTENANCE
11
!
!
4. Remove the engine oil filler cap.
5. Slide underneath the car and loosen
the oil pan drain plug by turning it counterclockwise oil pan with a wrench of the proper size. Be surethat a drain pan is in position to catch the oil as it drains out, then remove the drain plug.
WARNING:
Be very careful when draining theengine oil as it may be hot enough to burn you!
6. When the oil has stopped draining, replace the drain plug using a new gasket and retighten by turning it clockwise. Oil pan drain plug tightening torque : 3.5 ~ 4.5 kgf.m
7. Pull out the oil filter upper cap with element from the oil filter housing.Using a clean cloth, remove any dirtor oil accumulated around the oilfilter housing. 8. After mounting a new centrepipe O-
ring, new oil filter element and newO-ring to upper cap, install the up- per cap to oil filter housing and retighten by turning it clockwise. Donot over-tighten. Tightening torque : 2.5 kgf.m
CAUTION:
Do not use old oil filter upper cap O- ring and centrepipe O-ring.
!
9. Refill the crankcase with the recom- mended engine oil. Refer to the specification in chapter 9 for engine oil capacity.
CAUTION:
Slowly pour the recommended oilinto a funnel. Do not overfill to preverd engine to camage.
! 10. Start the engine and check to be
sure no oil is leaking from the drain plug or oil filter.
11. Shut off the engine and recheck
the oil level.
NOTE:
o It is recommended that the en- gine oil and filter should be changed by an Hyundai authorised repairer.
o Always dispose of used engine oil in an environmentally accept-able manner. It is suggested that it be placed in a sealed container and taken to a service station formaybe reclaimation. Do not pour the oil on the ground or put it into the household trash.
WARNING:
Used motor oil may cause irritation or cancer of the skin if left in contact with the skin for prolonged periodsof time. Wash your hands thoroughly with soap and warm water as soon as possible after handling used oil.
fcuk-6.p65 12/27/2006, 10:16 AM
11
Page 462 of 490

6 OWNER MAINTENANCE
34
G290A01FC
5. Open the bonnet.
6. Draw the vertical line (through the centre of each headlight beam pat- tern) and the horizontal line (through the centre of each headlight beampattern) on the aiming screen.And then, draw the horizontal paral-lel line at 1.18 in. (30 mm) under the horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillipsscrewdriver - VERTICAL AIMING
8. Adjust each cut-off line of the low beam to each vertical line with a phillips screwdriver - HORIZONTALAIMING.
Horizontal Aiming
Vertical Aiming
HEADLIGHT AIMING ADJUSTMENT
G290A01FC-EAT Before performing aiming adjustment,
make sure of the following.
1. Keep all tyres inflated to the correct
pressure.
2. Place the vehicle on level ground and press the front bumper & rear bumper down several times. Place the vehicle at a distance of 118 in. (3,000 mm) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant,engine oil and fuel, and spare tyre,jack, and tools).
4. Clean the head lights lens and turn on the headlight (Low beam).
!WARNING:
o Do not smoke or have any other open flame near the vehicle whilst bleeding the fuel system.
o Be sure to carefully wipe away any water drained out in thismanner, because the fuel mixed in the water might be ignited and result in a fire.
Extracting air in the fuel filter If you drove until you have no fuel left
or if you replaced the fuel filter, be sureto extract air in the fuel system as it makes you difficult to start the engine.
1) Remove the air extract nozzle cap
on the fuel filter.
2) Pump up and down until the fuel flows out of the plug opening.
NOTE: Use cloths when you extract air so
that the fuel is not sprayed around. Clean the fuel around the fuel filteror the injection pump before start- ing the engine to prevent fire. Fi- nally, check each part if the fuel isleaking.
fcuk-6.p65 12/27/2006, 10:16 AM
34
Page 483 of 490

9 VEHICLE SPECIFICATIONS
4
Oil & Grease Standard
API SJ, SL SAE 5W-20, 5W-30
or ABOVE, SAE 10W-30 (ABOVE 0°F)
ILSAC GF-3 SAE 15W-40 (ABOVE 10°F)
or ABOVE SAE 20W-50 (ABOVE 20°F)
API CH-4 SAE 30 (0°C ~ 40°C)
or ABOVE, SAE 20W-40 (ABOVE -10°C)
ACEA B4 SAE 15W-40 (ABOVE -15°C)
or ABOVE SAE 10W-30 (-20°C ~ 40°C) SAE 5W-30 (-25°C ~ 40°C) SAE 0W-30 (BELOW 10°C) *1, *2
*1. Restricted to driving condition and vehicle destination*2. Not recommended for sustained high speed vehicle operation Normal driving condition Severe driving condition HYUNDAI GENUINE PARTS MTF 75W/85 (API GL-4) HYUNDAI GENUINE ATF SP-III, DIAMOND ATF SP-III, SK ATF SP-III or other brands approved by Hyundai Motor Co., PSF-3 or Dexron 2 DOT 3, DOT 4 or equivalent Ethylene glycol base for aluminium radiator Q'ty (Imp.qts) (litre)
1.6 DOHC - 2.9 (3.3) (with oil filter) 1.8 DOHC - 3.5 (4.0) (with oil filter) 1.5 CRDi - 4.7 (5.3) (with oil filter) MAX. 1L /932 Miles (1500 Km) MAX. 1L /621 Miles (1000 Km)1.86 (2.15)
1.76 (2.0) (1.5 CRDi) 5.3 (6.1) (1.6 DOHC)5.8 (6.7)(1.8 DOHC) As required As requiredPetol engine : 5.4 (6.2) (1.6 DOHC)/ 5.7 (6.5) (1.8 DOHC)
Diesel engine : 5.5 (6.3)
LUBRICATION CHART
J080A07FC-EAT
Item
Engine Oil Petrol engine
Diesel engine
Recommends Engine Oil Consumption Transaxle
Power Steering Brake Fluid Coolant
Manual Auto
fcuk-9.p65 12/27/2006, 10:17 AM
4
Page 485 of 490

10INDEX
2
A ACCESSORY TRAY ................................................. 1-67
AIR CONDITIONING SWITCH.................................. 1-82
AIR CONDITIONING SYSTEM MAINTENANCE ....... 6-24
AIR CLEANER ELEMENT REPLACEMENT .............6-14
ANTENNA ................................................................. 1-95
ANTI-LOCK BRAKE SYSTEM (ABS) .......................2-14
ANTI-THEFT ALARM SYSTEM .................................. 1-8
ASHTRAY ................................................................. 1-61
AUTO FUEL CUT SWITCH ....................................... 1-75
AUTOMATIC TRANSAXLE .......................................2-10
AUTOMATIC TRANSAXLE FLUID ........................... 6-19
B BATTERY MAINTENANCE .......................................6-30
BEFORE STARTING THE ENGINE ............................ 2-3
BLEEDING THE FUEL SYSTEM .............................. 6-32
BONNET RELEASE .................................................. 1-70
BRAKE PEDAL FREEPLAY .....................................6-27
BRAKE TRACTION CONTROL SYSTEM (BTCS) .... 2-14
BRAKE SYSTEM CHECKING.................................. 6-22
C
CARE OF SEAT BELTS .... .......................................1-20
CARGO AREA COVER ............................................. 1-74
CATALYTIC CONVERTOR OPERATING PRECAUTIONS ............................................................................. 7-3
CENTRE VENTILATOR ............................................. 1-76
CENTRAL DOOR LOCKS ......... .................................. 1-7
CHANGING A FLAT TYRE ......................................... 3-7
CHECKING THE CLUTCH FLU ID .............................6-23CHILD-PROOF REAR DOOR LOCK
........................... 1-7
CHILD RESTRAINT SYSTEM ................................... 1-24
CIGAR LIGHTER ....................................................... 1-60
CLUTCH PEDAL FREEPLAY ....................................6-26
COMBINATION IGNITION SWITCH ANDSTEERING LOCK ....................................................... 2-3
COOLANT TEMPERATURE GAUGE ........................1-49
DDAILY OPERATING CHECKS .................................... 6-5
DIGITAL CLOCK ....................................................... 1-59
DOOR LOCKS ............................................................. 1-5
DOOR WINDOWS ..................................................... 1-11
DRINK HOLDER ........................................................ 1-61
DRIVE BELTS ........................................................... 6-27
DRIVING FOR ECONOMY ....... .................................2-18
E EFFECTIVE BRAKING ............................................. 2-17
ELECTRIC COOLING FANS ..................................... 6-31
ELECTRONIC STABILITY PROGRAM (ESP) ...........2-16
EMERGENCY TOWING ............................................ 3-14
EMISSION CONTROL SYSTEM ................................. 7-2
ENGINE COMPARTMENT ....... ................................... 6-2
ENGINE COOLANT CHECKING AND REPLACING . 6-12
ENGINE OIL AND FILTER REPLACEMENT .............. 6-8
ENGINE OIL CONSUMPTION .................................... 6-8
ENGINE OIL REPLENISHMENT ................................. 6-7
ENGINE OIL ................................................................ 6-5 EXTERIOR REAR VIEW MIRROR ........................... 1-67
fcuk-10.p65 12/27/2006, 10:14 AM
2