key Hyundai Terracan 2004 Owner's Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2004, Model line: Terracan, Model: Hyundai Terracan 2004Pages: 361, PDF Size: 4.69 MB
Page 10 of 361
FEATURES OF YOUR HYUNDAI
1- 2 B030A01A-AAT KEYS
B030B01HP
B030B01A-AAT Record Your Key Number
B030A01HP
A code number is stamped on the number plate that came with the keys to your Hyundai. Thiskey number plate should not be left with the keysbut kept in a safe place, not in the vehicle. Thekey number should also be recorded in a placewhere it can be found in an emergency.If you need additional keys, or if you should loseyour keys, your authorized Hyundai dealer canmake new keys if you can supply the key num-ber.
For greater convenience, the same key operatesall the locks in your Hyundai. However, becausethe doors can be locked without a key, carryinga spare key is recommended in case you acci-dentally lock one key inside the car.
B010F01A-AAT Operation in Foreign CountriesIf you are going to drive your Hyundai in another country, be sure to:
o Observe all regulations regarding registra-
tion and insurance.
o Determine that acceptable fuel is available. B020A01S-GAT BREAKING IN YOUR NEW HYUNDAI During the First 2,000 Km (1,200 Miles) No formal "break-in" procedure is required with your new Hyundai. However, you can contributeto the economical operation and durability of yourHyundai by observing the following recommen-dations during the first 2,000 km (1,200 miles).
o Don't drive faster than 88 km/h (55 mph).
o While driving, keep your engine speed (rpm, or revolutions per minute) between 2,000 rpmand 4,000 rpm.
o Use moderate acceleration. Don't start, de- press the accelerator pedal fully.
o For the first 300 km (200 miles), try to avoid hard stops.
o Don't lug the engine (in other words, don't drive so slowly in too high a gear that theengine "bucks":shift to a lower gear).
o Whether going fast or slow, vary your speed from time to time.
o Don't let the engine idle longer than 3 minutes for a catalytic converter equipped engine.
o Don't tow a trailer during the first 2,000 km (1,200 miles) of operation.
Page 11 of 361
FEATURES OF YOUR HYUNDAI 1- 3
B880A01A-GAT IMMOBILIZER SYSTEM (If Installed)
- For Diesel Engine (2.5 TCI) or
Gasoline Engine
The immobilizer system is an anti-theft device, designed to deter automobile theft. B880B01HP-GAT Keys For greater convenience, your Hyundai has two types of keys as shown in the illustration. (1) ID key
This key must be used first to register a unique ID code in the ICM. This ID code isthen recorded onto the master keys. Bothsides of the key have a Hyundai logo.
(2) Master key This key is for general use. It will open alllocks on your vehicle.One side of the key has the Hyundai logo andthe other side has the "M" symbol.If your vehicle is equipped with Theft-alarmsystem, the master keys with the function oftransmitter will be provided. (Type B)
CAUTION: Don't lose your ID key or forget the password. Always keep your ID key in a place where youremember and record your password. If youdon't have both the password and ID key,consult your authorized Hyundai dealer.
(3) If you need additional keys or if you should lose your keys, your authorized Hyundai dealer can make new keys if you can supplythe key number and ID key.
NOTE: If you make your own duplicate key, you will not be able to cancel the system or start theengine.
B880B01HP
B880B02HP
Light Purple
ID key
ID key Master key
Master key B880C01A-GAT Key Numbers The vehicle key number is recorded upon a metal tag attached to the keys when the vehicle is firstdelivered to you.The key number should be recorded and kept in asafe place in case the need to order further keysarises. New keys are available from any Hyundaidealer by quoting the relevant key number.
B880C01HP
B880C02HP
Type B
BlackType A
Page 12 of 361
FEATURES OF YOUR HYUNDAI
1- 4
In the interest of security, the metal tag attached to the keys which bears the key number should beremoved from the key ring after you receiveyour new vehicle. In addition, key numbers cannotbe provided by Hyundai for security reasons.If you need additional keys or if you should loseyour keys, your authorized Hyundai dealer canmake new keys if you can supply the key numberand ID key. B880D01HP-GAT Limp Home Procedures In case the immobilizer system is out of order, you cannot start the engine without the limphome procedures with ignition key.The following procedure is how to start the en-gine with the function of the limp home. (0, 1, 2,3 as a sample password). NOTE: You can get the limp home password whenthe vehicle is first delivered to you. If you donot have the password, consult your autho-rized Hyundai dealer.
1. To set the password you may turn the ignition
key "ON" and then turn it "OFF" according to the digit numbers. For example, turn the igni-tion key once for digit number "1", and twicefor "2", and so on. However, for the digitnumber "0", you must turn the ignition key for10 times. 2. Wait for 3~10 seconds.
3. You may set the remaining number of digits
by following the same procedures 1 and 2.
4. If all of four digits have been tried success- fully, from this time, you have to start yourengine within 30 seconds. If you start yourengine after 30 seconds, your engine will notstart.
NOTE:If the engine dies while driving after limphome procedure, you can start your enginewithin 8 seconds without limp home proce-dure again. After doing the limp home procedure, you have to consult with your authorized Hyundai dealer assoon as possible. CAUTION: If you cannot start your engine in spite of limphome procedure, have your vehicle towed byan authorized Hyundai dealer. B885A01HP-GAT IMMOBILIZER SYSTEM (If Installed) - For Diesel Engine (2.9 CRDi) The immobilizer system is an anti-theft device, designed to deter automobile theft. B885B01HP-GAT Keys
B885B01HP
Type A
B885B02HP
Type B
Master keys Master keys
Page 13 of 361
FEATURES OF YOUR HYUNDAI 1- 5
All of the locks fitted to the vehicle are operated by the same key. However, since it is possible tolock the doors without the use of the key, careshould be exercised to ensure that the key doesnot become locked inside the vehicle by mistake.If your vehicle is equipped with Theft-alarm sys-tem, the master keys with the function of trans-mitter will be provided (Type B). NOTE: If you make your own duplicate key, you willnot be able to cancel the system or start theengine. CAUTION:
o The password should be recorded and
kept in a safe place in case the need toorder further keys arises.
o If you forget the password, consult your authorized Hyundai dealer. B885C01O-GAT Key Numbers
B885C01HP
B885C02HP
The vehicle key number is recorded upon a metal tag attached to the keys when the vehicle is firstdelivered to you.The key number should be recorded and kept ina safe place in case the need to order further keys
arises. New keys are available from any Hyundaidealer by quoting the relevant key number.
B885D01O-GAT Limp Home Procedures In case the immobilizer warning indicator blinks for five seconds when the ignition key is turned to"ON" position, this indicates that the immobilizersystem is out of order. And you cannot start theengine without the limp home procedures withignition key.The following procedure is how to start the en-gine with the function of the limp home. (0, 1, 2,3 as a sample password).
B880D01HP-1
In the interest of security, the metal tag attached to the keys which bears the key number shouldbe removed from the key ring after you receiveyour new vehicle. In addition, key numbers can-not be provided by Hyundai for security reasons.If you need additional keys or if you should loseyour keys, your authorized Hyundai dealer canmake new keys.
Page 14 of 361
FEATURES OF YOUR HYUNDAI
1- 6 B040B01A-AAT Locking and Unlocking Front Doors With a Key
B040B01HP
LOCK
UNLOCK
B040A01A-AAT DOOR LOCKS WARNING:
o Unlocked doors can be dangerous. Be-
fore you drive away (especially if there are children in the car), be sure that all thedoors are securely closed and locked sothat the doors cannot be inadvertentlyopened from the inside. This helps ensurethat the doors will not be opened acciden-tally. Also, when combined with the properuse of seat belts, locking the doors helpskeep occupants from being ejected fromthe car in case of an accident.
o Before opening the door, always look for and avoid oncoming traffic.
B030C01Y-AAT ILLUMINATED IGNITION SWITCH Whenever a door is opened, the ignition switch will be illuminated for your convenience, provid-ed the ignition switch is not in the "ON" position.The light will go off approximately 10 secondsafter closing the door or when the ignition switchis turned on.
B030C01E
NOTE: You can get the limp home password whenthe vehicle is first delivered to you. If you donot have the password, consult your autho-rized Hyundai dealer.
1. To set the password you may turn the ignition
key "ON" and then turn it "OFF" according to the digit numbers, then the immobilizer indi-cator will blink along with the operation of theignition key. For example, turn the ignition keyonce for digit number "1", and twice for "2",and so on. However, for the digit number "0",you must turn the ignition key for 10 times.
2. Wait for 3~10 seconds.
3. You may set the remaining number of digits by following the same procedures 1 and 2.
4. If all of four digits have been tried success- fully, turn the ignition key "ON" and check thatthe immobilizer indicator illuminates. Fromthis time, you have to start your engine within30 seconds. If you start your engine after 30seconds, your engine will not start.
NOTE:If the engine dies while driving after limphome procedure, you can start your enginewithin 8 seconds without limp home proce-dure again.
5. If the immobilizer indicator blinks for five seconds, you have to try the limp home procedure again from the beginning. After doing the limp home procedure, you have toconsult with your authorized Hyundai dealer assoon as possible. CAUTION:
o If you fail to try the limp home procedure
with the sequence of three times, youhave to wait for about one hour to do thelimp home procedure again.
o If you cannot start your engine in spite of limp home procedure, have your vehicletowed by an authorized Hyundai dealer.
Page 15 of 361
FEATURES OF YOUR HYUNDAI 1- 7
o The door can be locked or unlocked with akey.
o Lock the door by turning the key toward the front of the vehicle and unlock it by turning the key toward the rear.
B040C02Y-DAT Locking from the Outside
B040C01HP
The doors can be locked without a key. To lock the doors, first push the inside lock switch to the"LOCK" position so that the red mark on theswitch is not visible, then close the door.The door will not lock if the key is left in the ignitionswitch when the front doors are closed. This isnormal. NOTE:
o When locking the door this way, be careful not to lock the door with the ignition keyleft in the vehicle. B040D01S-AAT Locking from the Inside To lock the doors from the inside, simply close the door and push the lock switch to the "LOCK"position. When this is done, neither the outsidenor the inside door handles can be used. NOTE: When the door is locked, the red mark on theswitch is not visible.HSM362
o To reduce the chance of theft, always
remove the ignition key, close all win- dows, and lock all doors when leavingyour vehicle unattended. B040E03A-AAT CHILD-PROTECTOR REAR DOOR LOCK Your Hyundai is equipped with a "child-protec- tor" rear door lock assembly. When the lockmechanism is engaged, the rear door cannot beopened from the inside. Its use is recommendedwhenever there are small children in the rearseat. To engage the child-protector feature so the door cannot be opened from the inside, move thechild-protector lever to the " " position andclose the door. Move the lever to the oppositedirection of the " " position when normal dooroperation is desired. If you wish to be able to open the door from the outside, the outside door handle will functionnormally.
B040E01HP
LOCK
UNLOCK
Page 16 of 361
FEATURES OF YOUR HYUNDAI
1- 8
Park the car and stop the engine. Arm the system as described below.
1) Remove the ignition key from the ignition switch.
2) Make sure that the engine hood and tail gate are closed and latched.
3) Lock the doors using the transmitter of the keyless entry system.
After completion of the steps above, the turn signal lights will blink once to indicate that thesystem is armed. NOTE:
1) If any door, tail gate or engine hood re- mains open, the system will not be armed.
2) If this happens, rearm the system as de- scribed above.
B070B02HP
LOCK
UNLOCK
Type B
B070A01A-AAT THEFT-ALARM SYSTEM (If installed)This system is designed to provide protection from unauthorized entry into the car. This systemis operated in three stages: the first is the "Armed"stage, the second is the "Alarm" stage, and thethird is the "Disarmed" stage. If triggered, thesystem provides an audible alarm with blinking ofthe turn signal lights. B070B01O-AAT Armed Stage
B070B01HP
LOCK
B040G01HP-AAT Central Door Locks
B040G01HP
The central door locking switch is located on the driver's arm rest. It is operated by depressing thedoor lock switch. NOTE:
o When pushing the front portion of the driver's door lock switch, all vehicle doorswill lock. If any door is open when theswitch is depressed, the door will remainlocked when closed.
o When pushing the rear portion of the switch, all vehicle doors will unlock.
o The central door locking is operated by turning the key toward the front or rear ofthe vehicle. UNLOCK
LOCK
UNLOCKType A
Page 17 of 361
FEATURES OF YOUR HYUNDAI 1- 9
B070C01HP-GAT Alarm Stage
CAUTION: Do not arm the system until all passengershave left the car. If the system is armed whilea passenger(s) remains in the car, the alarmmay be activated when the remainingpassenger(s) leaves the car.
B070D01HP-AAT Disarmed Stage The system will be disarmed when the driver's or passenger's door is unlocked by depressing the"UNLOCK" button on the transmitter.After completion of the step above, the turnsignal lights will blink twice to indicate that thesystem is disarmed. If any door, tail gate or engine hood is not opened within 30 seconds, the system will be rearmed. CAUTION: Only the transmitter can disarm the armedstage. If the transmitter does not disarm thesystem, it is necessary to take the followingsteps;
1. Unlock the door with the key, which willcause the alarm to be activated.
2. Insert the key in the ignition key cylinder and turn the ignition key to "ON" position.
3. Wait for 30 seconds.After completing the steps above, the system will be disarmed.
B070C01HP
The alarm will be activated if any of the following occurs while the car is parked and the system isarmed.
1) A front or rear door is opened without using the transmitter.
2) The tail gate is opened without using the transmitter.
3) The engine hood is opened. The siren will sound and the turn signal lights will blink continuouly for 27 seconds (Type B/ Type
A : This happens 3 times). To turn off the system,unlock the door or tail gate with the transmitter. CAUTION: Avoid trying to start the engine while thesystem is armed.
B070F01A-GAT Keyless Entry System (If installed) Locking doors
1. Close all doors.
2. Push the "LOCK" button on the transmitter.
3. At the same time all doors lock, the turn signal
lights will blink once to indicate that the sys-tem is armed.
Unlocking doors
1. Push the "UNLOCK" button on the transmit- ter.
2. At the same time all doors unlock, the turn signal lights will blink twice to indicate that the system is disarmed.
B070E02HP-GAT Replacing the batteryWhen the transmitter's battery begins to get weak, it may take several pushes on the buttonto lock or unlock the doors, and the LED will notlight. Replace the battery as soon as possible. Battery type : CR2032(Type A) or CR1616 (Type B)
Page 18 of 361
FEATURES OF YOUR HYUNDAI
1- 10
B060A03L-DAT POWER WINDOWS
(1) (2)
B060A01HP
The power windows operate when the ignition key is in the "ON" position. The main switchesare located on the driver's armrest and controlthe front and rear windows on both sides of thevehicle. The windows may be opened by de-pressing the appropriate window switch andclosed by pulling up the switch. To open thewindow on the driver's side, press the switch(1)halfway down. The window moves as long asthe switch is operated. To fully open the driver'swindow automatically, press the switch fullydown. In automatic operation, the window willfully open even if you let go of the switch. To stopat the desired opening, pull up and release theswitch. In order to prevent operation of thepassanger front and rear windows, a windowlock switch(2) is provided on the armrest of thedriver's door. To disable the power windows,press the window lock switch. To revert tonormal operation, press the window lock switcha second time.
Replacement instructions:Type A:
MSO-0048-1
Screwdriver
1. Carefully separate the case with a blade screwdriver as shown in the illustration.
MSO-0048-2
Battery
CaseType B:
HMXOM033-2
Transmitter
Case
HMXOM033-3
Battery
Hole
Battery cover
2. Remove the old battery from the case and note the polarity. Make sure the polarity of the new battery is the same(+side facing down),then insert it in the transmitter. 1. Carefully separate the case with a phillips
screwdriver.
2. Take off the battery cover after separating the transmitter.
3. Remove the old battery from the transmitter with a blade screwdriver inserted in the holeand note the polarity. Make sure the polarityof the new battery is the same(+side facingup), then insert it in the transmitter.
Page 19 of 361
FEATURES OF YOUR HYUNDAI 1- 11
B060A02HP
NOTE: The power windows can be operated for 30seconds after the ignition key is turned to the"ACC" or "LOCK" positions, or removed fromthe ignition switch.If the front doors are opened during this 30second period, the power windows can nolonger be operated without the ignition keyturned to the "ON" position. WARNING:
(1) Be careful that someone's head, hands and body are not trapped by a closingwindow.
(2) Never try to operate the main switch on the driver's door and the individual doorwindow switch in opposing directions atthe same time. If this is done, the windowwill stop and cannot be opened or closed.
(3) Do not leave children alone in the car. Always remove the ignition key for theirsafety. To move the seat toward the front or rear, pull thelock release lever upward. This will release theseat on its track so you can move it forward orrearward to the desired position. When you findthe position you want, release the lever and slidethe seat forward or rearward on its track until itlocks into the desired position and cannot bemoved further.
B080A01A-AAT ADJUSTABLE FRONT SEATS WARNING: Never attempt to adjust the seat while thevehicle is moving. This could result in loss ofcontrol or an accident which may cause death,serious injury, or property damage. B080B02A-AAT Adjusting Seat Forward and Rearward
B080B01HP
B080C01A-AAT Adjusting Seatback Angle
To recline the seatback, lean forward to take your weight off it, then pull up on the recliner controllever at the outside edge of the seat. Now leanback until the desired seatback angle is achieved.To lock the seatback into position, release therecliner control lever. WARNING: To minimize risk of severe injury in the eventof a collision or a sudden stop, both the driverand passenger seatbacks should always bein an upright position while the vehicle is inmotion. The protection provided by the seat
B080C01HP
WARNING: To ensure the seat is locked securely, at-tempt to move the seat forward or rearwardwithout using the lock release lever.