control INFINITI FX35 2004 Workshop Manual

AT-44
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
How To Perform Trouble Diagnosis For Quick and Accurate RepairACS007A4
INTRODUCTION
The TCM receives a signal from the vehicle speed sensor, accelerator pedal position sensor (throttle position
sensor) or PNP switch and provides shift control or lock-up control via A/T solenoid valves.
The TCM also communicates with the ECM by means of a signal
sent from sensing elements used with the OBD-related parts of the
A/T system for malfunction-diagnostic purposes. The TCM is capa-
ble of diagnosing malfunctioning parts while the ECM can store mal-
functions in its memory.
Input and output signals must always be correct and stable in the
operation of the A/T system. The A/T system must be in good oper-
ating condition and be free of valve seizure, solenoid valve malfunc-
tion, etc.
It is much more difficult to diagnose a error that occurs intermittently
rather than continuously. Most intermittent errors are caused by poor
electric connections or improper wiring. In this case, careful check-
ing of suspected circuits may help prevent the replacement of good
parts.
A visual check only may not find the cause of the errors. A road test
with CONSULT-II (or GST) or a circuit tester connected should be
performed. Follow the AT- 4 5 , "
WORK FLOW" .
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a drive ability complaint. The cus-
tomer can supply good information about such errors, especially
intermittent ones. Find out what symptoms are present and under
what conditions they occur. A “DIAGNOSTIC WORKSHEET” as
shown on the example (Refer to AT- 4 6
) should be used.
Start your diagnosis by looking for “conventional” errors first. This will
help troubleshoot drive ability errors on an electronically controlled
engine vehicle.
Also check related Service bulletins.
SAT631IB
SAT632I
SEF234G

TROUBLE DIAGNOSIS
AT-47
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
4❏ Execute all road tests and enter checks in required inspection items.AT- 5 4
4-1.Check before engine is started
AT- 5 5
❏ The A/T CHECK Indicator Lamp does come on. AT- 1 9 1 .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 4
, AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-108, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT-112, "
DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT-116, "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-123, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-125, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-127, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-129, "
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" .
❏ AT-133, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-134, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-135, "
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)" .
❏ AT-136, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-139, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-143, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-145, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-147, "
DTC P1730 A/T INTERLOCK" .
❏ AT-150, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-152, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-154, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-156, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-158, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-160, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-162, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-164, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-168, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-170, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-172, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-178, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-180, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-182, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-184, "
DTC P1846 ATF PRESSURE SWITCH 6" .
4-2.Check at Idle
AT- 5 5
❏ AT- 1 9 3 , "Engine Cannot Be Started In “P” or “N” Position" .
❏ AT- 1 9 3 , "
In “P” Position, Vehicle Moves When Pushed" .
❏ AT- 1 9 4 , "
In “N” Position, Vehicle Moves" .
❏ AT- 1 9 5 , "
Large Shock (“N” to “D” Position)" .
❏ AT- 1 9 8 , "
Vehicle Does Not Creep Backward In “R” Position" .
❏ AT- 2 0 1 , "
Vehicle Does Not Creep Forward In “D” Position" .
4-3.Cruise test
AT- 5 7
Part 1
❏ AT- 2 0 3 , "
Vehicle Cannot Be Started From D1" .
❏ AT- 2 0 6 , "
A/T Does Not Shift: D1 → D2" .
❏ AT- 2 0 8 , "
A/T Does Not Shift: D2 → D3" .
❏ AT- 2 11 , "
A/T Does Not Shift: D3 → D4" .
❏ AT- 2 1 3 , "
A/T Does Not Shift: D4 → D5" .
❏ AT- 2 1 6 , "
A/T Does Not Perform Lock-up"
❏ AT- 2 1 8 , "A/T Does Not Hold Lock-up Condition" .
❏ AT- 2 2 0 , "
Lock-up Is Not Released" .
❏ AT- 2 2 1 , "
Engine Speed Does Not Return To Idle" .

AT-48
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
44-3Part 2
AT- 6 0
❏ AT-203, "Vehicle Cannot Be Started From D1" .
❏ AT-206, "
A/T Does Not Shift: D1 → D2" .
❏ AT-208, "
A/T Does Not Shift: D2 → D3" .
❏ AT- 2 11 , "
A/T Does Not Shift: D3 → D4" .
Part 3
AT- 6 1
❏ AT-222, "Cannot Be Changed to Manual Mode" .
❏ AT-223, "
A/T Does Not Shift: 5th gear → 4th gear" .
❏ AT-225, "
A/T Does Not Shift: 4th gear → 3rd gear" .
❏ AT-227, "
A/T Does Not Shift: 3rd gear → 2nd gear" .
❏ AT-229, "
A/T Does Not Shift: 2nd gear → 1st gear" .
❏ AT-231, "
Vehicle Does Not Decelerate By Engine Brake" .
❏ Perform self-diagnostics. Enter checks for detected items. AT- 9 4
, AT-103
❏ AT-105, "DTC U1000 CAN COMMUNICATION LINE" .
❏ AT-108, "
DTC P0615 START SIGNAL CIRCUIT" .
❏ AT- 11 2 , "
DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
❏ AT- 11 6 , "
DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-121, "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT-123, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-125, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-127, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-129, "
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)" .
❏ AT-133, "
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)" .
❏ AT-134, "
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)" .
❏ AT-135, "
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)" .
❏ AT-136, "
DTC P1705 THROTTLE POSITION SENSOR" .
❏ AT-139, "
DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-143, "
DTC P1716 TURBINE REVOLUTION SENSOR" .
❏ AT-145, "
DTC P1721 VEHICLE SPEED SENSOR MTR" .
❏ AT-147, "
DTC P1730 A/T INTERLOCK" .
❏ AT-150, "
DTC P1731 A/T 1ST ENGINE BRAKING" .
❏ AT-152, "
DTC P1752 INPUT CLUTCH SOLENOID VALVE" .
❏ AT-154, "
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-156, "
DTC P1757 FRONT BRAKE SOLENOID VALVE" .
❏ AT-158, "
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-160, "
DTC P1762 DIRECT CLUTCH SOLENOID VALVE" .
❏ AT-162, "
DTC P1764 DIRECT CLUTCH SOLENOID VALVE FUNCTION" .
❏ AT-164, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC P1769 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE
FUNCTION" .
❏ AT-168, "
DTC P1772 LOW COAST BRAKE SOLENOID VALVE" .
❏ AT-170, "
DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION" .
❏ AT-172, "
DTC P1815 MANUAL MODE SWITCH" .
❏ AT-178, "
DTC P1841 ATF PRESSURE SWITCH 1" .
❏ AT-180, "
DTC P1843 ATF PRESSURE SWITCH 3" .
❏ AT-182, "
DTC P1845 ATF PRESSURE SWITCH 5" .
❏ AT-184, "
DTC P1846 ATF PRESSURE SWITCH 6" .
5❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunction
parts.
6❏ Perform all road tests and enter the checks again for the required items.AT- 5 4
7❏ For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunction parts.
See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection proce-
dures.)AT- 6 5
8❏ Erase the results of the self-diagnostics from the TCM.AT- 4 0,
AT- 1 0 4

TROUBLE DIAGNOSIS
AT-65
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Symptom ChartACS007AG

The diagnostics item numbers show the sequence for inspection. Inspect in order from Item 1.

Overhaul and inspection inside the A/T only if A/T fluid condition is NG. Refer to AT- 5 1 , "Fluid Condition
Check" .
No. Items Symptom Condition Diagnostic ItemReference
page
1
Shift
ShockLarge shock. (N → D
position)
Refer to AT-195,
"Large Shock (“N” to
“D” Position)" .ON vehicle1. Engine idle speedEC-37
(for
VQ35DE)
or EC-685

(for
VK45DE)
2. Engine speed signalAT-121
3. Accelerator pedal position sensorAT-136
4. Control linkage adjustmentAT-234
5. ATF temperature sensorAT-139
6. ATF pressure switch 1 and front brake solenoid valveAT-178,
AT-156
7. CAN communication lineAT-105
8. Fluid level and stateAT- 5 1
9. Line pressure testAT- 5 2
10. Control valve with TCMAT-242
OFF vehicle11. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17, "Cross-Sectional View (2WD Models)" or AT-18, "Cross-
Sectional View (AWD Models)" )AT-286
2Shock is too large
when changing D1 →
D
2 or M1 → M2 .ON vehicle1. Accelerator pedal position sensorAT-136
2. Control linkage adjustmentAT-234
3. ATF pressure switch 5 and direct clutch solenoid valveAT-182,
AT-160
4. CAN communication lineAT-105
5. Engine speed signalAT-121
6. Turbine revolution sensorAT-143
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
8. Fluid level and stateAT- 5 1
9. Control valve with TCMAT-242
OFF vehicle 10. Direct clutchAT-323

AT-66
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
3
Shift
ShockShock is too large
when changing D2 →
D
3 or M2 → M3 .ON vehicle1. Accelerator pedal position sensorAT- 1 3 6
2. Control linkage adjustmentAT- 2 3 4
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4,
AT- 1 6 4
4. CAN communication lineAT- 1 0 5
5. Engine speed signalAT- 1 2 1
6. Turbine revolution sensorAT- 1 4 3
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
8. Fluid level and stateAT- 5 1
9. Control valve with TCMAT- 2 4 2
OFF vehicle 10. High and low reverse clutchAT- 3 2 0
4Shock is too large
when changing D3 →
D
4 or M3 → M4 .ON vehicle1. Accelerator pedal position sensorAT- 1 3 6
2. Control linkage adjustmentAT- 2 3 4
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 8 0,
AT- 1 5 2
4. CAN communication lineAT- 1 0 5
5. Engine speed signalAT- 1 2 1
6. Turbine revolution sensorAT- 1 4 3
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
8. Fluid level and stateAT- 5 1
9. Control valve with TCMAT- 2 4 2
OFF vehicle 10. Input clutchAT- 3 0 8
5Shock is too large
when changing D4 →
D
5 or M4 → M5 .ON vehicle1. Accelerator pedal position sensorAT- 1 3 6
2. Control linkage adjustmentAT- 2 3 4
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 8,
AT- 1 5 6

4. CAN communication lineAT- 1 0 5
5. Engine speed signalAT- 1 2 1
6. Turbine revolution sensorAT- 1 4 3
7. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
8. Fluid level and stateAT- 5 1
9. Control valve with TCMAT- 2 4 2
OFF vehicle10. Front brake (brake band)AT- 2 7 411. Input clutchAT- 3 0 8
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-67
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
6
Shift
ShockShock is too large for
downshift when accel-
erator pedal is
pressed.ON vehicle1. Accelerator pedal position sensorAT-136
2. Control linkage adjustmentAT-234
3. CAN communication lineAT-105
4. Engine speed signalAT-121
5. Turbine revolution sensorAT-143
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
7. Fluid level and stateAT- 5 1
8. Control valve with TCMAT-242
OFF vehicle9. Front brake (brake band)AT-27410. Input clutch AT-308
11. High and low reverse clutchAT-320
12. Direct clutchAT-323
7Shock is too large for
upshift when acceler-
ator pedal is released.ON vehicle1. Accelerator pedal position sensorAT-136
2. Control linkage adjustmentAT-234
3. Engine speed signalAT-121
4. CAN communication lineAT-105
5. Turbine revolution sensorAT-143
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
7. Fluid level and stateAT- 5 1
8. Control valve with TCMAT-242
OFF vehicle9. Front brake (brake band)AT-27410. Input clutch AT-308
11. High and low reverse clutch AT-320
12. Direct clutch AT-323
8Shock is too large for
lock-up.ON vehicle1. Accelerator pedal position sensorAT-136
2. Control linkage adjustmentAT-234
3. Engine speed signalAT-121
4. CAN communication lineAT-105
5. Turbine revolution sensorAT-143
6. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
7. Torque converter clutch solenoid valveAT-123
8. Fluid level and stateAT- 5 1
9. Control valve with TCMAT-242
OFF vehicle 10. Torque converterAT-286
No. Items Symptom Condition Diagnostic ItemReference
page

AT-68
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
9Shift
ShockShock is too large
during engine brake.ON vehicle1. Accelerator pedal position sensorAT- 1 3 6
2. Control linkage adjustmentAT- 2 3 4
3. CAN communication lineAT- 1 0 5
4. Fluid level and stateAT- 5 1
5. Control valve with TCMAT- 2 4 2
OFF vehicle6. Front brake (brake band)AT- 2 7 47. Input clutch AT- 3 0 8
8. High and low reverse clutchAT- 3 2 0
9. Direct clutch AT- 3 2 3
10
No Up
ShiftGear does not change
from D
1 → D2 or from
M
1 → M2 .
Refer to AT-206, "
A/T
Does Not Shift: D1 →
D2" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 2,
AT- 1 6 0
4. Line pressure testAT- 5 2
5. CAN communication lineAT- 1 0 5
6. Control valve with TCMAT- 2 4 2
OFF vehicle 7. Direct clutchAT- 3 2 3
11Gear does not change
from D
2 → D3 or from
M
2 → M3 .
Refer to AT-208, "
A/T
Does Not Shift: D2 →
D3" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4,
AT- 1 6 4
4. Line pressure testAT- 5 2
5. CAN communication lineAT- 1 0 5
6. Control valve with TCMAT- 2 4 2
OFF vehicle 7. High and low reverse clutchAT- 3 2 0
12Gear does not change
from D
3 → D4 or from
M
3 → M4 .
Refer to AT- 2 11 , "
A/T
Does Not Shift: D3 →
D4" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 8 0,
AT- 1 5 2
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 8,
AT- 1 5 6
5. Line pressure testAT- 5 2
6. CAN communication lineAT- 1 0 5
7. Control valve with TCMAT- 2 4 2
OFF vehicle 8. Input clutchAT- 3 0 8
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-69
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
13No Up
ShiftGear does not change
from D
4 → D5 or from
M
4 → M5 .
Refer to AT-213, "
A/T
Does Not Shift: D4 →
D5" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
3. ATF pressure switch 1 and front brake solenoid valveAT-178,
AT-156
4. ATF pressure switch 5 and direct clutch solenoid valveAT-182,
AT-160
5. Turbine revolution sensorAT-143
6. Line pressure testAT- 5 2
7. CAN communication lineAT-105
8. Control valve with TCMAT-242
OFF vehicle9. Front brake (brake band)AT-28610. Input clutchAT-308
14
No Down
ShiftIn D or M range, does
not downshift to 4th
gear.
Refer to AT-223, "A/T
Does Not Shift: 5th
gear → 4th gear" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145

3. ATF pressure switch 1 and front brake solenoid valveAT-178
,
AT-156
4. ATF pressure switch 5 and direct clutch solenoid valveAT-182,
AT-160
5. CAN communication lineAT-105
6. Line pressure testAT- 5 2
7. Control valve with TCMAT-242
OFF vehicle8. Front brake (brake band)AT-2869. Input clutchAT-308
15In D or M range, does
not downshift to 3rd
gear.
Refer to AT-225, "A/T
Does Not Shift: 4th
gear → 3rd gear" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
3. ATF pressure switch 3 and input clutch solenoid valveAT-180,
AT-152
4. ATF pressure switch 1 and front brake solenoid valveAT-178,
AT-156
5. CAN communication lineAT-105
6. Line pressure testAT- 5 2
7. Control valve with TCMAT-242
OFF vehicle 8. Input clutchAT-308
No. Items Symptom Condition Diagnostic ItemReference
page

AT-70
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
16
No Down
ShiftIn D or M range, does
not downshift to 2nd
gear.
Refer to AT-227, "A/T
Does Not Shift: 3rd
gear → 2nd gear" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5

3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4
,
AT- 1 6 4
4. CAN communication lineAT- 1 0 5
5. Line pressure testAT- 5 2
6. Control valve with TCMAT- 2 4 2
OFF vehicle 7. High and low reverse clutchAT- 3 2 0
17In D or M range, does
not downshift to 1st
gear.
Refer to AT-229, "A/T
Does Not Shift: 2nd
gear → 1st gear" .ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 2,
AT- 1 6 0
4. CAN communication lineAT- 1 0 5
5. Line pressure testAT- 5 2
6. Control valve with TCMAT- 2 4 2
OFF vehicle 7. Direct clutchAT- 3 2 3
18Slips/Will
Not
engageWhen D or M position,
remains in 1st gear.ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
3. Direct clutch solenoid valveAT- 1 6 0
4. Line pressure testAT- 5 2
5. CAN communication lineAT- 1 0 5
6. Control valve with TCMAT- 2 4 2
OFF vehicle7. 3rd one-way clutchAT- 3 0 6
8. 1st one-way clutchAT- 3 1 4
9. Gear systemAT- 2 7 4
10. Reverse brakeAT- 2 8 6
11. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-17, "
Cross-Sectional View (2WD Models)" or AT-18,
"Cross-Sectional View (AWD Models)" )AT- 2 8 6
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17,
"Cross-Sectional View (2WD Models)" or AT- 1 8 , "Cross-
Sectional View (AWD Models)" )AT- 2 8 6
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-71
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
19
Slips/Will
Not
engageWhen D or M position,
remains in 2nd gear.ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
3. Low coast brake solenoid valveAT-168
4. Line pressure testAT- 5 2
5. CAN communication lineAT-105
6. Control valve with TCMAT-242
OFF vehicle7. 3rd one-way clutchAT-306
8. Gear systemAT-274
9. Direct clutchAT-323
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17,
"Cross-Sectional View (2WD Models)" or AT-18, "Cross-
Sectional View (AWD Models)" )AT-286
20When D or M position,
remains in 3rd gear.ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
3. Line pressure testAT- 5 2
4. CAN communication lineAT-105
5. Control valve with TCMAT-242
OFF vehicle6. 3rd one-way clutchAT-306
7. Gear systemAT-274
8. High and low reverse clutchAT-320
9. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7 , "
Cross-Sectional View (2WD Models)" or AT- 1 8 ,
"Cross-Sectional View (AWD Models)" )AT-286
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17,
"Cross-Sectional View (2WD Models)" or AT-18, "Cross-
Sectional View (AWD Models)" )AT-286
No. Items Symptom Condition Diagnostic ItemReference
page