immobilizer INFINITI FX35 2005 Workshop Manual

IDX-6
ALPHABETICAL INDEX
M
M/ANT - Wiring diagram .................................... AV-52
MAFS - Wiring diagram ..... EC-189, EC-197, EC-896,
EC-904
Magnet clutch ................................. ATC-84, ATC-144
MAIN - Wiring diagram ...................... EC-164, EC-855
Maintenance (engine)(VQ35DE) ...................... MA-14
Major overhaul (Final drive) .............. FFD-16, RFD-16
Major overhaul (Transfer) .................................. TF-45
Mass air flow sensor (MAFS) ............ EC-186, EC-195,
EC-893
, EC-902
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ....... EC-703, EC-1393
MIL/DL - Wiring diagram .................. EC-703, EC-1393
Mirror, door ..................................................... GW-114
Mirror, out side ................................................ GW-114
Misfire .............................................. EC-285, EC-1022
Mode door control linkage adjustment ............. ATC-72
Mode door motor ............................ ATC-70, ATC-131
Molding - See Exterior ................... EI-25, EI-29, EI-32
Multiport fuel injection (MFI) system .... EC-31, EC-722
Multiport fuel injection precautions ....................... GI-7
N
NATS - Wiring diagram .................................... BL-216
NAVI - Wiring diagram ..................................... AV-106
Navigation system ............................................. AV-87
NVH troubleshooting (EM) .............................. EM-170
NVH troubleshooting (EM)(VQ35DE) ............... EM-13
NVH troubleshooting (Final drive) ......... FFD-6, RFD-7
NVH troubleshooting (Propeller shaft) ................. PR-3
NVH troubleshooting (Transfer) ........................... TF-8
NVIS (Nissan vehicle immobilizer system) precautions
GI-3
O
O2H1B1 - Wiring diagram ................................ EC-879
O2H1B2 - Wiring diagram ................................ EC-881
O2H2B1 - Wiring diagram .................. EC-180, EC-887
O2H2B2 - Wiring diagram .................. EC-182, EC-889
O2S1B1 - Wiring diagram ... EC-937, EC-947, EC-959
O2S1B2 - Wiring diagram ... EC-939, EC-949, EC-961
O2S2B1 - Wiring diagram .. EC-230, EC-240, EC-445,
EC-456
, EC-968, EC-978, EC-1190, EC-1201
O2S2B2 - Wiring diagram .. EC-232, EC-242, EC-447,
EC-458
, EC-970, EC-980, EC-1192, EC-1203
Oil cooler (engine)(VQ35DE) ............................. LU-14
Oil filter(VK45DE) .............................................. LU-28
Oil filter(VQ35DE) .............................................. LU-10
Oil pan (engine)(VK45DE) .............................. EM-185
Oil pan (engine)(VQ35DE) ................................ EM-30
Oil pressure (engine)(VK45DE) ......................... LU-25
Oil pressure (engine)(VQ35DE) ........................... LU-8
Oil pressure relief valve (engine)(VQ35DE) ........ LU-6
Oil pump (A/T) ................................................. AT-308
Oil pump (engine)(VK45DE) .............................. LU-31
Oil pump (engine)(VQ35DE) .............................. LU-17
Oil pump regulator valve (engine)(VK45DE) ...... LU-31
Oil pump regulator valve (engine)(VQ35DE) ..... LU-17
Oil seal replacement (engine)(VK45DE) ......... EM-225
Oil seal replacement (engine)(VQ35DE) .......... EM-97
Oil seal replacement (front of final drive) .......... FFD-9,
RFD-10
Oil seal replacement (side of final drive) ......... FFD-11,
RFD-12
ORVR (On-board Refueling Vapor Recovery) .. EC-46,
EC-737
Out side mirror ............................................... GW-114
Overheat ........................................................ EC-1213
P
P/SCKT - Wiring diagram ................................ WW-57
Park/Neutral position switch ........... EC-609, EC-1283
Park/neutral position switch (A/T) .................... AT-114
Parking brake control ........................................... PB-3
PCV (positive crankcase ventilation) .. EC-51, EC-742
Personal lamp ..................................... LT-153, LT-187
PGC/V - Wiring diagram .. EC-338, EC-562, EC-1071,
EC-1235
PHASE - Wiring diagram ............................... EC-1045
PHSB1 - Wiring diagram .................................. EC-309
PHSB2 - Wiring diagram .................................. EC-311
Pilot bushing replacement - See Pilot
converter(VQ35DE) ........................................ EM-123
Piston assembly(VK45DE) ............................. EM-255
Piston assembly(VQ35DE) ............................. EM-135
Piston pin inspection(VK45DE) ....................... EM-262
Piston pin inspection(VQ35DE) ...................... EM-140
Piston ring inspection(VK45DE) ..................... EM-263
Piston ring inspection(VQ35DE) ..................... EM-141
Piston to bore clearance(VK45DE) ................. EM-266
Piston to bore clearance(VQ35DE) ................ EM-144
PNP/SW - Wiring diagram .............. EC-611, EC-1285
POS - Wiring diagram ..................... EC-302, EC-1038
POWER - Wiring diagram ................................... PG-4
Power door mirror .............................................. BL-21
Power seat ......................................................... SE-92
Power socket ................................................... WW-57
Power steering fluid level ........................ PS-8, MA-37
Power steering gear ........................................... PS-19
Power steering hydraulic pressure .................... PS-31
Power steering oil pump .................................... PS-31
Power steering system bleeding .......................... PS-8
Power supply routing .......................................... PG-3
Power window .................................................. GW-15
PRE/SE - Wiring diagram EC-355, EC-361, EC-1088,
EC-1094
Precations for Leak detection dye .................. ATC-16
Precautions (General) ........................................... GI-4
Pressure switch 1 .............................. AT-156, AT-175
Pressure switch 2 ............................................ AT-168
Pressure switch 3 .............................. AT-152, AT-177
Pressure switch 5 .............................. AT-160, AT-179

PRECAUTIONS PS-3
C
D E
F
H I
J
K L
M A
B
PS
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AGS000GO
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectAGS000L5
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″ LOCK ″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC ″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK ″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.
Precautions for Steering SystemAGS000GP

Before disassembly, thoroughly clean the outside of the unit.

Disassembly should be done in a clean work area. It is important to prevent the internal parts from becom-
ing contaminated by dirt or other foreign matter.

For easier and proper assembly, place disassembled parts in order on a parts rack.