torque INFINITI FX35 2005 Workshop Manual

OVERHAUL AT-279
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
1. O-ring 2. Oil pump cover 3. O-ring
4. Oil pump housing 5. Self-sealing bolt 6. Torque converter
7. Converter housing 8. Oil pump housing oil seal 9. Bearing race
10. Needle bearing 11. O-ring 12. Front carrier assembly
13. Snap ring 14. Front sun gear 15. 3rd one-way clutch
16. Snap ring 17. Bearing race 18. Needle bearing
19. Seal ring 20. Input clutch assembly 21. Needle bearing
22. Rear internal gear 23. Brake band 24. Mid carrier assembly
25. Needle bearing 26. Bearing race 27. Rear carrier assembly
28. Needle bearing 29. Mid sun gear 30. Seal ring
31. Rear sun gear 32. 1st one-way clutch 33. Snap ring
34. Needle bearing 35. High and low reverse clutch hub 36. Snap ring
37. Bearing race 38. Needle bearing

AT-290
DISASSEMBLY
Revision: 2005 July 2005 FX
DISASSEMBLYPFP:31020
DisassemblyACS0081L
CAUTION:
Do not disassemble parts behind Drum Support. Refer to AT- 1 8 , "
Cross-Sectional View (2WD Models)"
or AT- 1 9 , "Cross-Sectional View (AWD Models)" .
1. Drain ATF through drain plug.
2. Remove torque converter by holding it firmly and turing while pulling straight out.
3. Check torque converter one-way clutch using check tool as shown in the figure.
a. Insert check tool into the groove of bearing support built into one-way clutch outer race.
b. When fixing bearing support with check tool, rotate one-way clutch spline using screwdriver.
c. Make sure that inner race rotates clockwise only. If not, replace torque converter assembly.
4. Remove converter housing from transmission case. CAUTION:
Be careful not to scratch converter housing.
SCIA5010E
SCIA3171E
SCIA3427E

AT-310
REPAIR FOR COMPONENT PARTS
Revision: 2005 July 2005 FX
3. Using the drift, install oil pump housing oil seal to the oil pump
housing until it is flush.
CAUTION:

Do not reuse oil seal.

Apply ATF to oil seal.
4. Install oil pump housing to oil pump cover.
5. Tighten bolts to the specified torque in numerical order shown in the figure after temporarily tightening them.
SCIA5313E
: 9.0 N·m (0.92 kg-m, 80 in-lb.)
SCIA6388E

AT-336
ASSEMBLY
Revision: 2005 July 2005 FX
ii. Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
iii. Tighten rear extension assembly mounting bolts to specified torque.
CAUTION:
Do not reuse self-sealing bolt.
b. AW D m o d e l s
i. Install gasket onto transmission case. CAUTION:

Completely remove all moisture, oil and old gasket, etc.
from the transmission case and adapter case assembly
mounting surfaces.

Do not reuse gasket.
ii. Install adapter case assembly to transmission case. CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
SCIA5029E
Rear extension assembly mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt: : 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA6941E
SCIA5231E
SCIA5186E

ASSEMBLY AT-337
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
iii. Tighten adapter case assembly mounting bolts (1) to specified
torque. [With bracket (2).]
: Bolt (10)
CAUTION:
Do not reuse self-sealing bolts (3).
Refer to GI section to mark sure icons (symbol marks) in the fig-
ure. Refer to GI-10, "
Components" .
35. Install needle bearing in drum support. CAUTION:
Apply petroleum jelly to needle bearing.
36. Install direct clutch assembly in reverse brake. CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
37. Install high and low reverse clutch assembly in direct clutch. Adapter case assembly mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt: : 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA7210E
SCIA5198E
SCIA5019E
SCIA2306E

ASSEMBLY AT-341
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
51. Install needle bearing to front sun gear.
CAUTION:
Apply petroleum jelly to needle bearing.
52. Adjust brake band tilting using clips so that brake band contacts front sun gear drum evenly.
53. Adjust brake band.
a. Loosen lock nut.
b. Tighten band servo anchor end pin to specified torque.
c. Back of band servo anchor end pin three turns.
d. Holding band servo anchor end pin, tighten lock nut to specified torque.
AdjustmentACS0081T
TOTAL END PLAY

Measure clearance between front sun gear and bearing race for
oil pump cover.

Select proper thickness of bearing race so that end play is within
specifications.
SCIA2808E
SCIA5033E
: 5.0 N·m (0.51 kg-m, 44 in-lb)
: 46 N·m (4.7 kg-m, 34 ft-lb)
SCIA5498E
SCIA2810E

AT-344
ASSEMBLY
Revision: 2005 July 2005 FX
Assembly (2)ACS0081U
1. Install O-ring to oil pump assembly.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
2. Install bearing race to oil pump assembly. CAUTION:
Apply petroleum jelly to bearing race.
3. Install oil pump assembly in transmission case. CAUTION:
Apply ATF to oil pump bearing.
4. Apply recommended sealant (Genuine RTV Silicone Sealant or equivalent. Refer to GI-48, "
Recommended Chemical Products
and Sealants" .) to oil pump assembly as shown in illustration.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
From the oil pump mounting bolts and oil pump mounting
bolt mounting surfaces.
5. Tighten oil pump mounting bolts to specified torque. CAUTION:
Apply ATF to oil pump bushing.
SCIA5172E
SCIA2811E
SCIA5321E
: 48 N·m (4.9 kg-m, 35 ft-lb)
SCIA2300E

ASSEMBLY AT-349
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
15. Install snap ring to A/T assembly harness connector.
16. Install magnets in oil pan.
17. Install oil pan to transmission case.
a. Install oil pan gasket to transmission case. CAUTION:

Do not reuse oil pan gasket.

Install it in the direction to align hole positions.

Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
b. Install oil pan (with oil pan gasket) to transmission case. CAUTION:

Install it so that drain plug comes to the position as
shown in the figure.

Be careful not to pinch harnesses.

Completely remove all moisture, oil and old gasket, etc.
from oil pan gasket mounting surface.
c. Tighten oil pan mounting bolts to the specified torque in numeri- cal order shown in the figure after temporarily tightening them.
CAUTION:
Do not reuse oil pan mounting bolts.
18. Install drain plug to oil pan. CAUTION:
Do not reuse drain plug gasket.
19. Install torque converter.
SCIA5300E
SCIA5200E
SCIA2308E
: 7.9 N·m (0.81 kg-m, 70 in-lb)
: 34 N·m (3.5 kg-m, 25 ft-lb)
SCIA4113E

AT-350
ASSEMBLY
Revision: 2005 July 2005 FX
a. Pour ATF into torque converter.

Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of ATF is
required for a new torque converter.

When reusing old torque converter, add the same amount
of ATF as was drained.
b. Install torque converter while aligning notches of torque con- verter with notches of oil pump.
CAUTION:
Install torque converter while rotating it.
c. Measure distance “A” to check that torque converter is in proper position.
SAT428DA
SCIA5010E
Distance “A”
VQ35DE models: 25.0 mm (0.98 in) or more
VK45DE models: 22.0 mm (0.87 in) or more
SAT017B

SERVICE DATA AND SPECIFICATIONS (SDS) AT-351
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsACS002S2
*1: Refer to MA-12, "Fluids and Lubricants" .
Vehicle Speed at Which Gear Shifting OccursACS002S3
2WD MODELS

At half throttle, the accelerator opening is 4/8 of the full opening.
AWD MODELS

At half throttle, the accelerator opening is 4/8 of the full opening.

At half throttle, the accelerator opening is 4/8 of the full opening.
Applied model
VQ35DE engine VK45DE engine
2WD AWD
Automatic transmission model RE5R05A
Transmission model code number 92X20, 90X3C 92X21, 90X3D 92X22, 90X3E
Stall torque ratio 2.0: 1
Transmission gear ratio 1st 3.540
2nd 2.264
3rd 1.471
4th 1.000
5th 0.834
Reverse 2.370
Recommended fluid Genuine NISSAN Matic J ATF*1
Fluid capacity 10.3 liter (10-7/8 US qt, 9-1/8 Imp qt)
CAUTION:

Use only Genuine NISSAN Matic J ATF. Do not mix with other fluid.

Using A/T fluid other than Genuine NISSAN Matic J ATF will deteriorate in driveability and automatic transmission durabil-
ity, and may damage the automatic transmission, which is not covered by the warranty.
Engine model VQ35DE
Throttle position Vehicle speed km/h (MPH)
D
1 → D2D2 → D3D3 → D4D4 → D5D5 → D4D4 → D3D3 → D2D2 → D1
Full throttle 66 - 74
(41 - 46) 106 - 114
(66 - 71) 165 - 173
(103 - 108) 236 - 244
(147 - 152) 232 - 240
(144 - 149) 145- 153
(90 - 95) 89 - 97
(55 - 60) 41 - 49
(25 - 30)
Half throttle 52 - 60
(32 - 37) 83 - 91
(52 - 57) 127 - 135
(79 - 84) 159 - 167
(99 - 104) 104 - 112
(65 - 70) 75 - 83
(47 - 52) 34 - 42
(21 - 26) 9 - 17
(6 - 11)
Engine model VQ35DE
Throttle position Vehicle speed km/h (MPH)
D
1 → D2D2 → D3D3 → D4D4 → D5D5 → D4D4 → D3D3 → D2D2 → D1
Full throttle 60 - 68
(37 - 42) 96 - 104
(60 - 65) 150 - 158
(93 - 98) 214 - 222
(133 - 138) 210 - 218
(130 - 135) 132 - 140
(82 - 87) 81 - 89
(50 - 55) 37 - 45
(23 - 28)
Half throttle 47 - 55
(29 - 34) 75 - 83
(47 - 52) 115 - 123
(71 - 76) 144 - 152
(89 - 94) 95 - 103
(59 - 64) 68 - 76
(42 - 47) 31 - 39
(19 - 24) 9 - 17
(6 -11)
Engine model VK45DE
Throttle position Vehicle speed km/h (MPH)
D
1 → D2D2 → D3D3 → D4D4 → D5D5 → D4D4 → D3D3 → D2D2 → D1
Full throttle 62 - 70
(39 - 43) 98 - 106
(61 - 66) 153 - 161
(95 - 100) 220 - 228
(137 - 142) 216 - 224
(134 - 139) 137 - 145
(85 - 90) 85 - 93
(53 - 58) 39 - 47
(24 - 29)
Half throttle 29 - 37
(18 - 23) 59 - 67
(37 - 42) 101 - 109
(63 - 68) 161 - 169
(100 - 105) 108 - 116
(67 - 72) 66 - 74
(41 - 46) 38 - 46
(24 - 29) 22 - 30
(14 - 19)