battery location INFINITI FX35 2006 User Guide

EM-244
[VK45DE]
ENGINE ASSEMBLY
Revision: 2006 December 2006 FX35/FX45
Preparation
1. Release fuel pressure. Refer to EC-746, "FUEL PRESSURE RELEASE" .
2. Drain engine coolant from radiator. Refer to CO-38, "
Changing Engine Coolant" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belts.
3. Disconnect both battery terminal. Refer to SC-4, "
BATTERY" .
4. Remove crankshaft position sensor (POS) from transmission. CAUTION:

Handle carefully to avoid dropping and shocks.

Do not disassemble.

Do not allow metal powder to adhere to magnetic part at sensor tip.

Do not place sensors in a location where they are exposed to magnetism.
5. Remove the following parts:

Hood assembly; Refer to BL-13, "HOOD" .

Engine cover; Refer to EM-173, "ENGINE ROOM COVER" .

Front and rear engine undercover

Air duct (inlet), air duct and air cleaner case assembly; Refer to EM-177, "AIR CLEANER AND AIR
DUCT" .

Drive belts; Refer to EM-174, "DRIVE BELTS" .

Radiator and radiator hoses (upper and lower); Refer to CO-41, "RADIATOR" .

Front road wheels and tires
Engine Room LH
1. Disconnect engine room harness from the engine side and set it aside for easier work.
2. Disconnect heater hoses, and install plugs to avoid leakage of engine coolant.
3. Disconnect ground cable from exhaust manifold cover to vehicle.
4. Disconnect vacuum hose between vehicle and engine and set it aside.
5. Discharge refrigerant from A/C circuit. Refer to ATC-137, "
REFRIGERANT LINES" .
6. Remove A/C piping from A/C compressor, and temporarily fasten it on vehicle with a rope. Refer to AT C -
139, "Components" .
Engine Room RH
1. Disconnect fuel feed hose and EVAP hose. Refer to EM-194, "FUEL INJECTOR AND FUEL TUBE" .
CAUTION:
Fit plugs onto disconnected hose to prevent fuel leak.
2. Disconnect engine room harness from the engine side and set it aside for easier work.
3. Disconnect ground cable from exhaust manifold cover to vehicle.
4. Disconnect vacuum hose between vehicle and engine and set it aside.
5. Disconnect reservoir tank of power steering oil pump from engine, and move it aside for easier work. CAUTION:
When temporarily securing, keep reservoir tank upright to avoid a fluid leak.
Vehicle Underbody
1. Remove front cross bar. Refer to FSU-6, "FRONT SUSPENSION ASSEMBLY" .
2. Disconnect power steering oil pump from engine. Move it from its location and secure with a rope for eas- ier work. Refer to PS-31, "
Removal and Installation (VK45DE Models)" .
3. Remove A/T fluid cooler tube. Refer to AT- 2 6 6 , "
TRANSMISSION ASSEMBLY" .
4. Remove exhaust front tube and center muffler with power tool. Refer to EX-3, "
EXHAUST SYSTEM" .
5. Remove RH and LH transverse link mounting bolts and nuts. Refer to FSU-14, "
TRANSVERSE LINK" .
6. Disconnect stabilizer connecting rod lower. Refer to FSU-6, "
FRONT SUSPENSION ASSEMBLY" .
7. Remove A/T control rod at control device assembly side. Then temporarily secure it on transmission, so that it does not sag. Refer to AT- 2 2 9 , "
SHIFT CONTROL SYSTEM" .

GI-12
HOW TO USE THIS MANUAL
Revision: 2006 December 2006 FX35/FX45
How to Follow Trouble DiagnosesNAS0006D
DESCRIPTION
NOTICE:
Trouble diagnoses indicate work procedures required to diagnose problems effectively. Observe the following
instructions before diagnosing.
1. Before performing trouble diagnoses, read the “Preliminary Check”, the “Symptom Chart” or the
“Work Flow”.
2. After repairs, re-check that the problem has been completely eliminated.
3. Refer to Component Parts and Harness Connector Location for the Systems described in each
section for identification/location of components and harness connectors.
4. Refer to the Circuit Diagram for quick pinpoint check.
If you need to check circuit continuity between harness connectors in more detail, such as when a
sub-harness is used, refer to Wiring Diagram in each individual section and Harness Layout in PG
section for identification of harness connectors.
5. When checking circuit continuity, ignition switch should be OFF.
6. Before checking voltage at connectors, check battery voltage.
7. After accomplishing the Diagnostic Procedures and Electrical Components Inspection, make sure
that all harness connectors are reconnected as they were.
HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES
1. Work and diagnostic procedure
Start to diagnose a problem using procedures indicated in enclosed test groups.
2. Questions and required results
Questions and required results are indicated in bold type in test group.
The meaning of are as follows:
SAIA0256E

GI-18
HOW TO USE THIS MANUAL
Revision: 2006 December 2006 FX35/FX45
Optional Splice
DESCRIPTION
SGI942
Num- ber Item Description
1 Power condition

This shows the condition when the system receives battery positive voltage (can be oper-
ated).
2 Fusible link

The double line shows that this is a fusible link.

The open circle shows current flow in, and the shaded circle shows current flow out.
3 Fusible link/fuse loca-
tion

This shows the location of the fusible link or fuse in the fusible link or fuse box. For arrange-
ment, refer to PG section, POWER SUPPLY ROUTING.
4Fuse

The single line shows that this is a fuse.

The open circle shows current flow in, and the shaded circle shows current flow out.
5 Current rating

This shows the current rating of the fusible link or fuse.
6 Connectors

This shows that connector E3 is female and connector M1 is male.

The G/R wire is located in the 1A terminal of both connectors.

Terminal number with an alphabet (1A, 5B, etc.) indicates that the connector is SMJ connec-
tor. Refer to PG section, SMJ (SUPER MULTIPLE JUNCTION).
7 Optional splice

The open circle shows that the splice is optional depending on vehicle application.
8 Splice

The shaded circle shows that the splice is always on the vehicle.
9 Page crossing

This arrow shows that the circuit continues to an adjacent page.

The A will match with the A on the preceding or next page.
10 Common connector

The dotted lines between terminals show that these terminals are part of the same connector.
11 Option abbreviation

This shows that the circuit is optional depending on vehicle application.
12 Relay

This shows an internal representation of the relay. For details, refer to PG section, STAN-
DARDIZED RELAY.
13 Connectors

This shows that the connector is connected to the body or a terminal with bolt or nut.

GW-32
POWER WINDOW SYSTEM
Revision: 2006 December 2006 FX35/FX45
Check BCM Power Supply and Ground CircuitNIS001R7
1. CHECK FUSE

Check 15A fuse [No. 1, located in fuse block (J/B)]

Check 15A fuse [No. 22, located in fuse block (J/B)]

Check 50A fusible link (letter M , located in the fuse and fusible link box).
NOTE:
Refer to GW-15, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Check BCM power supply circuit for open or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 49, 52 and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check BCM ground circuit for open or short.
Connector Terminal (Wire color)
Condition of
ignition switch Voltage [V]
(Approx.)
(+) (–)
M3 38 (W/L) Ground ON
Battery
voltage
M4 42 (L/R)
OFF
55 (G)
PIIB1383E
49 (B) – Ground : Continuity should exist.
52 (B) – Ground : Continuity should exist.
PIIA6161E

REAR WINDOW DEFOGGER GW-77
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2006 December 2006 FX35/FX45
Check BCM Power Supply and Ground Circuit NIS001SB
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, when perform the each trouble
diagnosis. Refer to BCS-14, "
CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK FUSE

Check 15A fuse [No.1, located in the fuse block (J/B)]

Check 15A fuse [No.22, located in the fuse block (J/B)]

Check 50A fusible link (letter M located in the fuse and fusible link box).
NOTE:
Refer to GW-67, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between BCM connector M3, M4 terminal 38, 42, 55 and ground.
OK or NG
OK >> GO TO 3.
NG >> Check BCM power supply circuit for open or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 49, 52 and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check BCM ground circuit for open or short. 38 (W/L) – Ground : Battery voltage
42 (L/R) – Ground : Battery voltage
55 (G) – Ground : Battery voltage
PIIA6160E
49 (B) – Ground : Continuity should exist.
52 (B) – Ground : Continuity should exist.
PIIA6161E

REAR WINDOW DEFOGGER GW-79
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2006 December 2006 FX35/FX45
3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M3 terminal 9 and ground.
OK or NG
OK >> Replace A/C and AV switch.
NG >> Replace BCM.
Check rear Window Defogger Power Supply Circuit NIS001SD
1. CHECK FUSE

Check 10A fuse [No.12, located in the fuse block (J/B)]

Check 20A fuse (No.75, located in the IPDM E/R)

Check 20A fuse (No.80, located in the IPDM E/R)
NOTE:
Refer to GW-67, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse, refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Remove rear window defogger relay.
3. Turn ignition switch ON.
4. Check voltage between rear window defogger relay connector E13 terminals 1, 3, 6 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness. 9 (L/W) – Ground : Approx. 5
PIIA6208E
1 (OR) – Ground : Battery voltage
3 (W) – Ground : Battery voltage
6 (R) – Ground : Battery voltage
PIIA4233E

GW-82
REAR WINDOW DEFOGGER
Revision: 2006 December 2006 FX35/FX45
3. CHECK REAR WINDOW DEFOGGER RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Remove rear window defogger relay.
3. Check continuity between rear window defogger relay connector E13 terminal 5, 7 and rear window defogger connector D104 ter-
minal 1.
OK or NG
OK >> Check condition of harness and connector.
NG >> Repair or replace harness.
Check Door Mirror Defogger Power Supply Circuit NIS001SF
1. CHECK FUSE

Check 15A fuse [No.8, located in fuse block (J/B)]
NOTE:
Refer to GW-67, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT 1
1. Turn ignition switch ON.
2. Check voltage between fuse block (J/B) connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK POWER SUPPLY CIRCUIT 2
Check voltage between fuse block (J/B) connector and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace fuse block (J/B). 5 (B) – 1 (W) : Continuity should exist.
7 (B) – 1 (W) : Continuity should exist.
PIIA9349E
Connector Terminal (Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
E201 2C (B) Ground Rear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF 0
PIIA2388E
Connector Terminal (Wire color)
Condition Voltage (V)
(Approx.)
(+) (–)
M2 5B (L) Ground Rear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF 0
PIIA2386E

LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION LT
A
B
LT
Revision: 2006 December 2006 FX35/FX45
LIGHTING SYSTEM
PRECAUTIONS ..................................................... ..... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
General Precautions for Service Operations ....... ..... 6
HEADLAMP - XENON TYPE - .............................. ..... 7
Component Parts and Harness Connector Location ..... 7
System Description ............................................. ..... 7
OUTLINE .......................................................... ..... 7
HEADLAMP OPERATION ............................... ..... 8
COMBINATION SWITCH READING FUNCTION ..... 9
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 9
AUTO LIGHT OPERATION (IF EQUIPPED) .... ..... 9
VEHICLE SECURITY SYSTEM ....................... ..... 9
XENON HEADLAMP ........................................ ..... 9
CAN Communication System Description ........... ..... 9
CAN Communication Unit ................................... ..... 9
Schematic ........................................................... ... 10
Wiring Diagram — H/LAMP — ............................ .... 11
Terminals and Reference Values for BCM .......... ... 15
Terminals and Reference Values for IPDM E/R .. ... 16
How to Proceed With Trouble Diagnosis ............. ... 17
Preliminary Check ............................................... ... 17
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 17
CONSULT-II Functions (BCM) ............................ ... 19
CONSULT-II BASIC OPERATION .................... ... 19
WORK SUPPORT ............................................ ... 19
DATA MONITOR .............................................. ... 19
ACTIVE TEST .................................................. ... 20
CONSULT-II Functions (IPDM E/R) .................... ... 21
CONSULT-II BASIC OPERATION .................... ... 21
DATA MONITOR .............................................. ... 21
ACTIVE TEST .................................................. ... 22
Headlamp Does Not Change To High Beam (Both
Sides) .................................................................. ... 22
Headlamp Does Not Change To High Beam (One
Side) .................................................................... ... 24
Headlamp Low Beam Does Not Illuminate (Both
Sides) .................................................................. ... 25 Headlamp Low Beam Does Not Illuminate (One
Side) .................................................................... ... 28
Headlamp RH Low Beam and High Beam Does Not
Illuminate ............................................................. ... 29
Headlamp LH Low Beam and High Beam Does Not
Illuminate ............................................................. ... 30
Headlamps Do Not Turn OFF .............................. ... 31
General Information for Xenon Headlamp Trouble
Diagnosis ............................................................. ... 33
Caution: ............................................................... ... 33
Xenon Headlamp Trouble Diagnosis ................... ... 33
Aiming Adjustment ............................................... ... 34
PREPARATION BEFORE ADJUSTING ........... ... 34
LOW BEAM AND HIGH BEAM ........................ ... 34
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ......... ... 35
Bulb Replacement ............................................... ... 35
HEADLAMP HIGH/LOW BEAM ....................... ... 35
DAYTIME/PARKING LAMP .............................. ... 36
FRONT TURN SIGNAL LAMP ......................... ... 36
FRONT SIDE MARKER LAMP ........................ ... 36
Removal and Installation ..................................... ... 36
REMOVAL ........................................................ ... 36
INSTALLATION ................................................ ... 37
Disassembly and Assembly ................................. ... 37
DISASSEMBLY ................................................ ... 37
ASSEMBLY ...................................................... ... 37
DAYTIME LIGHT SYSTEM .................................... ... 39
Component Parts and Harness Connector Location ... 39
System Description .............................................. ... 39
OUTLINE .......................................................... ... 39
DAYTIME LIGHT OPERATION ........................ ... 40
COMBINATION SWITCH READING FUNCTION ... 40
AUTO LIGHT OPERATION .............................. ... 40
CAN Communication System Description ........... ... 40
CAN Communication Unit .................................... ... 40
Schematic ............................................................ ... 41
Wiring Diagram — DTRL — ................................ ... 42
Terminals and Reference Values for BCM ........... ... 46
How to Proceed With Trouble Diagnosis ............. ... 48

LT-2Revision: 2006 December 2006 FX35/FX45 Preliminary Check ...............................................
... 49
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 49
INSPECTION PARKING BRAKE SWITCH CIR-
CUIT ................................................................. ... 50
CONSULT-II Functions (BCM) ............................. ... 51
CONSULT-II BASIC OPERATION .................... ... 51
DATA MONITOR ............................................... ... 51
ACTIVE TEST .................................................. ... 52
Daytime Light Control Does Not Operate Properly ... 53
Aiming Adjustment ............................................... ... 55
Bulb Replacement ............................................... ... 55
Removal and Installation ..................................... ... 55
Disassembly and Assembly ................................. ... 55
AUTO LIGHT SYSTEM .......................................... ... 56
Component Parts and Harness Connector Location ... 56
System Description .............................................. ... 56
OUTLINE .......................................................... ... 56
COMBINATION SWITCH READING FUNCTION ... 57
DELAY TIMER FUNCTION .............................. ... 57
CAN Communication System Description ........... ... 57
CAN Communication Unit .................................... ... 57
Major Components and Functions ....................... ... 57
Schematic ............................................................ ... 58
Wiring Diagram — AUTO/L — ............................. ... 59
Terminals and Reference Values for BCM ........... ... 62
Terminals and Reference Values for IPDM E/R ... ... 63
How to Proceed With Trouble Diagnosis ............. ... 63
Preliminary Check ............................................... ... 64
SETTING CHANGE FUNCTIONS .................... ... 64
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. ... 64
CONSULT-II Functions (BCM) ............................. ... 66
CONSULT-II BASIC OPERATION .................... ... 66
WORK SUPPORT ............................................ ... 66
DATA MONITOR ............................................... ... 66
ACTIVE TEST .................................................. ... 68
CONSULT-II Functions (IPDM E/R) ..................... ... 68
CONSULT-II BASIC OPERATION .................... ... 68
DATA MONITOR ............................................... ... 68
ACTIVE TEST .................................................. ... 69
Symptom Chart .................................................... ... 69
Lighting Switch Inspection ................................... ... 69
Optical sensor System Inspection ....................... ... 70
Removal and Installation of Optical Sensor ......... ... 72
REMOVAL ........................................................ ... 72
INSTALLATION ................................................. ... 72
HEADLAMP AIMING CONTROL ........................... ... 73
Schematic ............................................................ ... 73
Wiring Diagram — H/AIM — ................................ ... 74
Removal and Installation ..................................... ... 77
REMOVAL ........................................................ ... 77
INSTALLATION ................................................. ... 77
Switch Circuit Inspection ..................................... ... 77
FRONT FOG LAMP ............................................... ... 78
Component Parts and Harness Connector Location ... 78
System Description .............................................. ... 78
OUTLINE .......................................................... ... 78
FRONT FOG LAMP OPERATION .................... ... 79 COMBINATION SWITCH READING FUNCTION
... 79
EXTERIOR LAMP BATTERY SAVER CONTROL ... 79
CAN Communication System Description ........... ... 79
CAN Communication Unit .................................... ... 79
Wiring Diagram — F/FOG — ............................... ... 80
Terminals and Reference Values for BCM ........... ... 82
Terminals and Reference Values for IPDM E/R ... ... 82
How to Proceed With Trouble Diagnosis ............. ... 83
Preliminary Check ................................................ ... 83
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. ... 83
CONSULT-II Functions (BCM) ............................. ... 84
CONSULT-II Functions (IPDM E/R) ..................... ... 84
Front Fog Lamps Do Not Illuminate (Both Sides) ... 85
Front Fog Lamp Does Not Illuminate (One Side) . ... 87
Aiming Adjustment ............................................... ... 88
Bulb Replacement ................................................ ... 89
Removal and Installation ...................................... ... 89
REMOVAL ......................................................... ... 89
INSTALLATION ................................................. ... 89
TURN SIGNAL AND HAZARD WARNING LAMPS ... 90
Component Parts and Harness Connector Location ... 90
System Description .............................................. ... 90
TURN SIGNAL OPERATION ............................ ... 90
HAZARD LAMP OPERATION .......................... ... 91
REMOTE CONTROL ENTRY SYSTEM OPER-
ATION ............................................................... ... 92
COMBINATION SWITCH READING FUNCTION ... 93
CAN Communication System Description ........... ... 93
CAN Communication Unit .................................... ... 93
Schematic ............................................................ ... 94
Wiring Diagram — TURN — ................................ ... 95
Terminals and Reference Values for BCM ........... ... 98
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ......................................... ... 99
How to Proceed With Trouble Diagnosis ............. .102
Preliminary Check ................................................ .102
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................. .102
CONSULT-II Functions (BCM) ............................. .104
CONSULT-II BASIC OPERATION .................... .104
DATA MONITOR ............................................... .104
ACTIVE TEST ................................................... .104
Turn Signal Lamp Does Not Operate ................... .105
Rear Turn Signal Lamp Does Not Operate .......... .106
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operate ........................................... .108
Bulb Replacement (Front Turn Signal Lamp) ....... .110
Bulb Replacement (Rear Turn Signal Lamp) ....... .110
Removal and Installation of Front Turn Signal Lamp .110
Removal and Installation of Rear Turn Signal Lamp .110
Removal and Installation of Rear Combination
Lamp Control Unit ................................................ .110
REMOVAL ......................................................... .110
INSTALLATION ................................................. .110
LIGHTING AND TURN SIGNAL SWITCH ............. . 111
Removal and Installation ...................................... . 111
REMOVAL ......................................................... . 111
INSTALLATION ................................................. . 111

LT-3
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2006 December 2006 FX35/FX45 HAZARD SWITCH .................................................
..112
Removal and Installation ..................................... .. 112
REMOVAL ........................................................ .. 112
INSTALLATION ................................................ .. 112
COMBINATION SWITCH ....................................... ..113
Wiring Diagram — COMBSW — ......................... .. 113
Combination Switch Reading Function ............... .. 114
Terminals and Reference Values for BCM .......... .. 114
CONSULT-II Functions (BCM) ............................ .. 119
CONSULT-II BASIC OPERATION .................... .. 119
DATA MONITOR .............................................. .. 119
Combination Switch Inspection ........................... . 120
Removal and Installation ..................................... . 122
STOP LAMP .......................................................... . 123
Component Parts and Harness Connector Location . 123
System Description ............................................. . 123
Schematic ........................................................... . 124
Wiring Diagram — STOP/L — ............................. . 125
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 128
Stop Lamp Does Not Operate ............................. . 128
High-Mounted Stop Lamp ................................... . 130
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ . 130
Stop Lamp ........................................................... . 130
BULB REPLACEMENT .................................... . 130
REMOVAL AND INSTALLATION ..................... . 130
Rear Combination Lamp Control Unit ................. . 130
REMOVAL AND INSTALLATION ..................... . 130
BACK-UP LAMP ................................................... . 131
Wiring Diagram — BACK/L — ............................ . 131
Bulb Replacement ............................................... . 132
Removal and Installation ..................................... . 132
PARKING, LICENSE PLATE AND TAIL LAMPS .. . 133
Component Parts and Harness Connector Location . 133
System Description ............................................. . 133
OUT LINE ......................................................... . 133
OPERATION BY LIGHTING SWITCH ............. . 134
COMBINATION SWITCH READING FUNCTION . 135
EXTERIOR LAMP BATTERY SAVER CONTROL . 135
CAN Communication System Description ........... . 135
CAN Communication Unit ................................... . 135
Schematic ........................................................... . 136
Wiring Diagram — TAIL/L — ............................... . 137
Terminals and Reference Values for BCM .......... . 142
Terminals and Reference Values for IPDM E/R .. . 142
Terminals and Reference Value for Rear Combina-
tion Lamp Control Unit ........................................ . 144
How to Proceed With Trouble Diagnosis ............. . 144
Preliminary Check ............................................... . 144
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................. . 144
CONSULT-II Functions (BCM) ............................ . 145
CONSULT-II Functions (IPDM E/R) .................... . 145
Parking, License Plate and Side Marker Lamps Do
Not Illuminate ...................................................... . 145
Tail Lamp Does Not Operate ............................... . 151
Parking, License Plate, Side Maker and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ...... . 152 License Plate Lamp .............................................
.152
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................ .152
Front Parking Lamp ............................................. .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Tail Lamp ............................................................. .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Front Side Marker Lamp ...................................... .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Rear Side Marker Lamp ...................................... .153
BULB REPLACEMENT .................................... .153
REMOVAL AND INSTALLATION ..................... .153
Rear Combination Lamp Control Unit .................. .153
REMOVAL AND INSTALLATION ..................... .153
REAR COMBINATION LAMP ................................ .154
Bulb Replacement ............................................... .154
REAR FENDER SIDE (REAR SIDE MARKER
LAMP BULB) .................................................... .154
BACK DOOR SIDE (BACK-UP LAMP) ............ .154
Removal and Installation ..................................... .154
REMOVAL ........................................................ .154
INSTALLATION ................................................ .155
INTERIOR ROOM LAMP ....................................... .156
Component Parts and Harness Connector Location .156
System Description .............................................. .156
POWER SUPPLY AND GROUND ................... .157
SWITCH OPERATION ..................................... .158
ROOM LAMP TIMER OPERATION ................. .159
INTERIOR LAMP BATTERY SAVER CONTROL .160
Schematic ............................................................ .162
Wiring Diagram — ROOM/L — ........................... .164
Terminals and Reference Values for BCM ........... .172
How to Proceed With Trouble Diagnosis ............. .173
Preliminary Check ............................................... .173
CHECK FOR POWER SUPPLY AND GROUND
CIRCUIT ........................................................... .173
CONSULT-II Functions (BCM) ............................. .174
CONSULT-II BASIC OPERATION .................... .174
WORK SUPPORT (INT LAMP) ........................ .174
DATA MONITOR (INT LAMP) .......................... .174
ACTIVE TEST (INT LAMP) .............................. .175
WORK SUPPORT (BATTERY SAVER) ........... .176
DATA MONITOR (BATTERY SAVER) .............. .176
ACTIVE TEST (BATTERY SAVER) .................. .177
Interior Room Lamp Control Does Not Operate .. .177
Map Lamp Control Does Not Operate ................. .178
Personal Lamp Control Does Not Operate .......... .181
Ignition Key Hole Illumination Control Does Not
Operate ................................................................ .182
All Step Lamps Do Not Operate .......................... .184
All Interior Room Lamps Do Not Operate ............ .185
Bulb Replacement ............................................... .185
IGNITION KEY HOLE ILLUMINATION (WITH-
OUT INTELIGENT KEY) .................................. .185
IGNITION KEY HOLE ILLUMINATION (WITH
INTELIGENT KEY) ........................................... .185