check engine INFINITI FX35 2008 User Guide

AT-38
< SERVICE INFORMATION >
ON BOARD DIAGNOSTIC (OBD) SYSTEM
ON BOARD DIAGNOSTIC (OBD) SYSTEM
IntroductionINFOID:0000000001327143
The A/T system has two self-diagnostic systems.
The first is the emission-related on board diagnostic syst em (OBD-II) performed by the TCM in combination
with the ECM. The malfunction is indicated by the MI L (malfunction indicator lamp) and is stored as a DTC in
the ECM memory but not the TCM memory.
The second is the TCM original self-diagnosis indicat ed by the A/T CHECK indicator lamp. The malfunction is
stored in the TCM memory. The detected items are ov erlapped with OBD-II self-diagnostic items. For detail,
refer to AT-84, "
CONSULT-III Function (TRANSMISSION)".
OBD-II Function for A/T SystemINFOID:0000000001327144
The ECM provides emission-related on board diagnostic (O BD-II) functions for the A/T system. One function
is to receive a signal from the TCM used with OBD-relat ed parts of the A/T system. The signal is sent to the
ECM when a malfunction occurs in the corresponding OBD-related part. The other function is to indicate a
diagnostic result by means of the MIL (malfunction indi cator lamp) on the instrument panel. Sensors, switches
and solenoid valves are used as sensing elements.
The MIL automatically illuminates in “One or Two Trip Detection Logic” when a malfunction is sensed in rela-
tion to A/T system parts.
One or Two Trip Detection Logic of OBD-IIINFOID:0000000001327145
ONE TRIP DETECTION LOGIC
If a malfunction is sensed during the first test drive, the MIL will illuminate and the malfunction will be stored in
the ECM memory as a DTC. The TCM is not provided with such a memory function.
TWO TRIP DETECTION LOGIC
When a malfunction is sensed during the first test drive, it is stored in the ECM memory as a 1st trip DTC
(diagnostic trouble code) or 1st trip freeze frame data. At this point, the MIL will not illuminate. — 1st trip
If the same malfunction as that experienced during the fi rst test drive is sensed during the second test drive,
the MIL will illuminate. — 2nd trip
The “Trip” in the “One or Two Trip Detection Logic” means a driving mode in which self-diagnosis is performed
during vehicle operation.
OBD-II Diagnostic Trouble Code (DTC)INFOID:0000000001327146
HOW TO READ DTC AND 1ST TRIP DTC
DTC and 1st trip DTC can be read by the following methods.
( with CONSULT-III or GST) CONSULT-III or GST (Generic Scan Tool) Examples: P0705, P0720 etc.
These DTC are prescribed by SAE J2012.
(CONSULT-III also displays the malfunctioning component or system.)
 1st trip DTC No. is the same as DTC No.
 Output of the diagnostic troubl e code indicates that the indicated circuit has a malfunction. How-
ever, in case of the Mode II and GST, they do not indicate whether the malfunction is still occurring or
occurred in the past and returned to normal.
CONSULT-III can identify them as shown below, therefore, CONSULT-III (if available) is recom-
mended.
- DTC or 1st trip DTC of malfunction is displayed in SELF-DIAGNOSTIC RESULTS mode for “ENGINE” with
CONSULT-III. Time data indicates how many times the vehicle was driven after the last detection of a DTC.
- If the DTC is being detected currently, the time data will be “0”.
- If a 1st trip DTC is stored in t he ECM, the time data will be “1t”.
Freeze Frame Data and 1st Trip Freeze Frame Data
The ECM has a memory function, which stores the driv ing condition such as fuel system status, calculated
load value, engine coolant temperature, short term f uel trim, long term fuel trim, engine speed and vehicle
speed at the moment the ECM detects a malfunction.
Data which are stored in the ECM memory, along with the 1st trip DTC, are called 1st trip freeze frame data,
and the data, stored together with the DTC data, are called freeze frame data and displayed on CONSULT-III
or GST. The 1st trip freeze frame data can only be disp layed on the CONSULT-III screen, not on the GST. For
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ON BOARD DIAGNOSTIC (OBD) SYSTEMAT-39
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
detail, refer to EC-117, "CONSULT-III Function (ENGINE)" (for VQ35DE) or EC-695, "CONSULT-III Function
(ENGINE)" (for VK45DE).
Only one set of freeze frame data (either 1st trip freez e frame data of freeze frame data) can be stored in the
ECM. 1st trip freeze frame data is stored in the ECM me mory along with the 1st trip DTC. There is no priority
for 1st trip freeze frame data and it is updated each time a different 1st trip DTC is detected. However, once
freeze frame data (2nd trip detection/MIL on) is stored in the ECM memory, 1st trip freeze frame data is no
longer stored. Remember, only one set of freeze frame data can be stored in the ECM. The ECM has the fol-
lowing priorities to update the data.
Both 1st trip freeze frame data and freeze frame data (along with the DTC) are cleared when the ECM mem-
ory is erased.
HOW TO ERASE DTC
The diagnostic trouble code can be erased by CONSULT- III, GST or ECM DIAGNOSTIC TEST MODE as
described following.
 If the battery cable is disconnected, the diagnost ic trouble code will be lost within 24 hours.
 When you erase the DTC, using CONSULT-III or GS T is easier and quicker than switching the mode
selector on the ECM.
The following emission-related diagnostic information is cleared from the ECM memory when erasing DTC
related to OBD-II. For details, refer to EC-55, "
Emission-Related Diagnostic Information" (for VQ35DE) or EC-
633, "Emission-related Diagnostic Information" (for VK45DE).
 Diagnostic trouble codes (DTC)
 1st trip diagnostic trouble codes (1st trip DTC)
 Freeze frame data
 1st trip freeze frame data
 System readiness test (SRT) codes
 Test values
HOW TO ERASE DTC (WITH CONSULT-III)
1. The emission related diagnostic information in t he TCM and ECM can be erased by selecting “ALL Erase”
in the “Description” of “FINAL CHECK” mode with CONSULT-III.
HOW TO ERASE DTC (WITH GST)
1. If the ignition switch stays ON after repair work, be su re to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.
2. Perform “TCM SELF-DIAGNOSTIC PR OCEDURE (No Tools)”. Refer to AT-91, "
Diagnosis Procedure
without CONSULT-III". (The engine warm-up step can be ski pped when performing the diagnosis only to
erase the DTC.)
3. Select Mode 4 with Generic Scan Tool (GST). For details, refer to EC-125, "
Generic Scan Tool (GST)
Function" (for VQ35DE) or EC-704, "Generic Scan Tool (GST) Function" (for VK45DE).
HOW TO ERASE DTC (NO TOOLS)
The A/T CHECK indicator lamp is located on the instrument panel.
1. If the ignition switch stays ON after repair work, be su re to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.
2. Perform “TCM SELF-DIAGNOSTIC PR OCEDURE (No Tools)”. Refer to AT-91, "
Diagnosis Procedure
without CONSULT-III". (The engine warm-up step can be ski pped when performing the diagnosis only to
erase the DTC.)
3. Perform “OBD-II SELF-DI AGNOSTIC PROCEDURE (No tools)”. Refer to EC-55, "
Emission-Related
Diagnostic Information" (for VQ35DE) or EC-633, "Emission-related Diagnostic Information" (for
VK45DE).
Priority Items
1 Freeze frame data Misfire — DTC: P0300 - P0306
Fuel Injection System Function — DTC: P0171, P0172, P0174, P0175
2 Except the above items (Includes A/T related items)
3 1st trip freeze frame data
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-40
< SERVICE INFORMATION >
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Malfunction Indicator Lamp (MIL)
INFOID:0000000001327147
DESCRIPTION
The MIL is located on the instrument panel.
1. The MIL will light up when the ignition switch is turned ON with- out the engine running. This is a bulb check.
 If the MIL does not light up, refer to DI-34
, or see EC-591 (for
VQ35DE) or EC-1194
(for VK45DE).
2. When the engine is started, the MIL should go off. If the MIL remains on, the on board diagnostic system has
detected an engine system malfunction.
SEF217U
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-42
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
When there is an A/T first gear engine brake judgment malfunction, the low coast brake solenoid is switched
OFF to avoid the engine brake operation.
Line Pressure Solenoid
The solenoid is switched OFF and the line pressure is set to the maximum hydraulic pressure to make driving
possible.
Torque Converter Clutch Solenoid
The solenoid is switched OFF to release the lock-up.
Low Coast Brake Solenoid
When a malfunction (electrical or functional) occurs, in or der to make driving possible, if the solenoid is ON,
the transmission is held in 2nd gear; if the solenoid is OFF, the A/T is held in 4th gear. (Engine brake is not
applied in 1st and 2nd gear.)
Input Clutch Solenoid
If a malfunction (electrical or functi onal) occurs with the solenoid either ON or OFF, the A/T is held in 4th gear
to make driving possible.
Direct Clutch Solenoid
If a malfunction (electrical or functi onal) occurs with the solenoid either ON or OFF, the A/T is held in 4th gear
to make driving possible.
Front Brake Solenoid
If a malfunction (electrical or functi onal) occurs with the solenoid ON, in order to make driving possible, the A/
T is held in 5th gear; if the solenoid is OFF, 4th gear.
High and Low Reverse Clutch Solenoid
If a malfunction (electrical or functi onal) occurs with the solenoid either ON or OFF, the A/T is held in 4th gear
to make driving possible.
Turbine Revolution Sensor 1 or 2
The control is the same as if there were no turbi ne revolution sensors, 5th gear and manual mode are prohib-
ited.
How to Perform Trouble Diagnosis for Quick and Accurate RepairINFOID:0000000001327150
INTRODUCTION
The TCM receives a signal from the vehicle speed sensor , accelerator pedal position sensor (throttle position
sensor) or PNP switch and provides shift cont rol or lock-up control via A/T solenoid valves.
The TCM also communicates with the ECM by means of a signal
sent from sensing elements used with the OBD-related parts of the
A/T system for malfunction-diagnos tic purposes. The TCM is capa-
ble of diagnosing malfunctioning parts while the ECM can store mal-
functions in its memory.
Input and output signals must always be correct and stable in the
operation of the A/T system. The A/T system must be in good oper-
ating condition and be free of valve seizure, solenoid valve malfunc-
tion, etc.
It is much more difficult to diagnose a error that occurs intermittently
rather than continuously. Most inte rmittent errors are caused by poor
electric connections or improper wiring. In this case, careful check-
ing of suspected circuits may help prevent the replacement of good
parts.
A visual check only may not find the cause of the errors. A road test
with CONSULT-III (or GST) or a circuit tester connected should be
performed. Follow the "WORK FLOW".
SAT631IB
SAT632I
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-43
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such errors, especially
intermittent ones. Find out what symptoms are present and under
what conditions they occur. A “DIAGNOSTIC WORKSHEET” as
shown on the example (Refer to "Diagnostic Worksheet Chart")
should be used.
Start your diagnosis by looking for “conventional” errors first. This will
help troubleshoot driveability errors on an electronically controlled
engine vehicle.
Also check related Service bulletins.
WORK FLOW
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malf unction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
Make good use of the two sheets provided, “Informati on from Customer” and “Diagnostic worksheet chart”, to
perform the best troubleshooting possible.
Work Flow Chart
SEF234G
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-45
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Diagnostic Worksheet Chart
Customer name MR/MS Model and Year VIN
Trans. Model Engine Mileage
Malfunction Date Manuf. Date In Service Date
Frequency
❏ Continuous ❏ Intermittent ( times a day)
Symptoms ❏ Vehicle does not move. ( ❏ Any position ❏ Particular position)
❏ No up-shift ( ❏ 1st → 2nd ❏ 2nd → 3rd ❏ 3rd → 4th ❏ 4th → 5th)
❏ No down-shift ( ❏ 5th → 4th ❏ 4th → 3rd ❏ 3rd → 2nd ❏ 2nd → 1st)
❏ Lock-up malfunction
❏ Shift point too high or too low.
❏ Shift shock or slip ( ❏ N → D ❏ Lock-up ❏ Any drive position)
❏ Noise or vibration
❏ No kick down
❏ No pattern select
❏ Others
()
A/T CHECK indicator lamp ❏ Continuously lit ❏ Not lit
Malfunction indicator lamp (MIL) ❏ Continuously lit ❏ Not lit
1 ❏ Read the item on cautions concerning fail-safe and understand the customer's complaint. AT- 4 1
2❏
A/T fluid inspection AT- 4 9❏ Leak (Repair leak location.)
❏ State
❏ Amount
3 ❏
Stall test and line pressure test AT- 4 9
❏ Stall test
❏ Torque converter one-way clutch
❏ Front brake
❏ High and low reverse clutch
❏ Low coast brake
❏ Forward brake
❏ Reverse brake
❏ Forward one-way clutch ❏
1st one-way clutch
❏ 3rd one-way clutch
❏ Engine
❏ Line pressure low
❏ Except for input clutch and direct
clutch, clutches and brakes OK
❏ Line pressure inspection - Suspected part:
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-46
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
4❏
Perform all road tests and enter checks in required inspection items. AT- 4 9
4-1.Check before engine is started
AT- 5 3
❏ The A/T CHECK Indicator Lamp does come on. AT- 1 7 0.
❏ Perform self-diagnostics. Enter checks for detected items. AT- 8 4
, AT- 9 1.
❏ DTC U1000 CAN COMMUNICATION LINE AT- 9 4
.
❏ DTC P0615 START SIGNAL CIRCUIT AT- 9 7
.
❏ DTC P0700 TCM AT- 1 0 1
❏ DTC P0705 PARK/NEUTRAL POSITION SWITCH AT- 1 0 2.
❏ DTC P0717 TURBINE REVOLUTION SENSOR AT- 1 0 6
.
❏ DTC P0720 VEHICLE SPEED SENSO R A/T (REVOLUTION SENSOR) AT- 1 0 8
.
❏ DTC P0725 ENGINE SPEED SIGNAL AT- 11 2
.
❏ DTC P0731 A/T 1ST GEAR FUNCTION AT- 11 4
.
❏ DTC P0732 A/T 2ND GEAR FUNCTION AT- 11 6
.
❏ DTC P0733 A/T 3RD GEAR FUNCTION AT- 11 8
.
❏ DTC P0734 A/T 4TH GEAR FUNCTION AT- 1 2 0
.
❏ DTC P0735 A/T 5TH GEAR FUNCTION AT- 1 2 2
.
❏ DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE AT- 1 2 4
.
❏ DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) AT- 1 2 6
.
❏ DTC P0745 LINE PRESSURE SOLONOID VALVE AT- 1 2 8
.
❏ DTC P1705 THROTTLE POSITION SENSOR AT- 1 3 0
.
❏ DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT AT- 1 3 2
.
❏ DTC P1721 VEHICLE SPEED SENSOR MTR AT- 1 3 7
.
❏ DTC P1730 A/T INTERLOCK AT- 1 3 9
.
❏ DTC P1731 A/T 1ST ENGINE BRAKING AT- 1 4 1
.
❏ DTC P1752 INPUT CLUTCH SOLENOID VALVE AT- 1 4 3
.
❏ DTC P1757 FRONT BRAKE SOLENOID VALVE AT- 1 4 5
.
❏ DTC P1762 DIRECT CLUTCH SOLENOID VALVE AT- 1 4 7
.
❏ DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE AT- 1 4 9
.
❏ DTC P1772 LOW COAST BRAKE SOLENOID VALVE AT- 1 5 1
.
❏ DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION AT- 1 5 3
.
❏ DTC P1815 MANUAL MODE SWITCH AT- 1 5 5
.
4-2. Check at Idle
AT- 5 3
❏ AT- 1 7 0 , "Engine Cannot Be Started in "P" or "N" Position".
❏ AT- 1 7 1 , "
In "P" Position, Vehicle Moves When Pushed"
❏ AT- 1 7 2 , "In "N" Position, Vehicle Moves".
❏ AT- 1 7 3 , "
Large Shock ("N" to "D" Position)".
❏ AT- 1 7 5 , "
Vehicle Does Not Creep Backward in "R" Position".
❏ AT- 1 7 8 , "
Vehicle Does Not Creep Forward in "D" Position".
4-3. Cruise Test
AT- 5 3
Part 1
❏ AT- 1 8 0 , "
Vehicle Cannot Be Started from D1".
❏ AT- 1 8 2 , "
A/T Does Not Shift: D1→ D2".
❏ AT- 1 8 4 , "
A/T Does Not Shift: D2→ D3".
❏ AT- 1 8 6 , "
A/T Does Not Shift: D3→ D4".
❏ AT- 1 8 8 , "
A/T Does Not Shift: D4→ D5".
❏ AT- 1 9 0 , "
A/T Does Not Lock-up"
❏ AT- 1 9 2 , "A/T Does Not Hold Lock-up Condition".
❏ AT- 1 9 4 , "
Lock-up Is Not Released".
❏ AT- 1 9 4 , "
Engine Speed Does Not Return to Idle".
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-47
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
44-3. Part 2
AT- 5 3
❏ AT- 1 8 0 , "Vehicle Cannot Be Started from D1".
❏ AT- 1 8 2 , "
A/T Does Not Shift: D1→ D2".
❏ AT- 1 8 4 , "
A/T Does Not Shift: D2→ D3".
❏ AT- 1 8 6 , "
A/T Does Not Shift: D3→ D4".
Part 3 AT- 5 3
❏ AT- 1 9 5 , "Cannot Be Changed to Manual Mode".
❏ AT- 1 9 6 , "
A/T Does Not Shift: 5th Gear → 4th Gear".
❏ AT- 1 9 7 , "
A/T Does Not Shift: 4th Gear → 3rd Gear".
❏ AT- 1 9 9 , "
A/T Does Not Shift: 3rd Gear → 2nd Gear".
❏ AT- 2 0 1 , "
A/T Does Not Shift: 2nd Gear → 1st Gear".
❏ AT- 2 0 2 , "
Vehicle Does Not Decelerate by Engine Brake".
❏ Perform self-diagnostics. Enter checks for detected items. AT- 8 4
, AT- 9 1.
❏ DTC U1000 CAN CO MMUNICATION LINE AT- 9 4
.
❏ DTC P0615 START SIGNAL CIRCUIT AT- 9 7
.
❏ DTC P0700 TCM AT- 1 0 1
❏ DTC P0705 PARK/NEUTRAL POSITION SWITCH AT- 1 0 2.
❏ DTC P0717 TURBINE REVOLUTION SENSOR AT- 1 0 6
.
❏ DTC P0720 VEHICLE SPEED SENS OR A/T (REVOLUTION SENSOR) AT- 1 0 8
.
❏ DTC P0725 ENGINE SPEED SIGNAL AT- 11 2
.
❏ DTC P0731 A/T 1ST GEAR FUNCTION AT- 11 4
.
❏ DTC P0732 A/T 2ND GEAR FUNCTION AT- 11 6
.
❏ DTC P0733 A/T 3RD GEAR FUNCTION AT- 11 8
.
❏ DTC P0734 A/T 4TH GEAR FUNCTION AT- 1 2 0
.
❏ DTC P0735 A/T 5TH GEAR FUNCTION AT- 1 2 2
.
❏ DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE AT- 1 2 4
.
❏ DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) AT-126
.
❏ DTC P0745 LINE PRESSURE SOLONOID VALVE AT- 1 2 8
.
❏ DTC P1705 THROTTLE POSITION SENSOR AT- 1 3 0
.
❏ DTC P1710 A/T FLUID TEMPERATURE SENSOR CIRCUIT AT- 1 3 2
.
❏ DTC P1721 VEHICLE SPEED SENSOR MTR AT- 1 3 7
.
❏ DTC P1730 A/T INTERLOCK AT- 1 3 9
.
❏ DTC P1731 A/T 1ST ENGINE BRAKING AT- 1 4 1
.
❏ DTC P1752 INPUT CLUTCH SOLENOID VALVE AT- 1 4 3
.
❏ DTC P1757 FRONT BRAKE SOLENOID VALVE AT- 1 4 5
.
❏ DTC P1762 DIRECT CLUTCH SOLENOID VALVE AT- 1 4 7
.
❏ DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE AT- 1 4 9
.
❏ DTC P1772 LOW COAST BRAKE SOLENOID VALVE AT- 1 5 1
.
❏ DTC P1774 LOW COAST BRAKE SOLENOID VALVE FUNCTION AT- 1 5 3
.
❏ DTC P1815 MANUAL MODE SWITCH AT-155
.
5 ❏ Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunctioning parts.
6 ❏ Perform all road tests and enter the checks again for the required items. AT- 4 9
7❏
For any remaining NG items, perform the “diagnostics procedure” and repair or replace the malfunctioning
parts. See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection pro-
cedures.) AT- 5 9
8
❏ Erase the results of the self-diagnostics from the TCM and the ECM. AT- 8 4,
AT-
91
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-50
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
A/T Fluid Condition Check
Inspect the A/T fluid condition.
STALL TEST
Stall Test Procedure
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2. Drive for about 10 minutes to warm up the vehicle so that the A/T fluid temperature is 50 to 80 °C (122 to 176 °F). Check the
amount of ATF. Replenish if necessary.
3. Securely engage the parking brake so that the tires do not turn.
4. Start engine, apply foot brake, and place selector lever in “D” position.
5. While holding down the foot brake, gradually press down the accelerator pedal.
6. Quickly read off the stall speed, then quickly remove your foot from the accelerator pedal.
CAUTION:
Do not hold down the accelerator pedal for more than 5 sec-
onds during this test.
7. Move the selector lever to the “N” position.
8. Cool down the ATF. CAUTION:
Run the engine at idle for at least 1 minute.
Fluid condition Conceivable Cause Required Operation
Varnished (viscous
varnish state) Clutch, brake
scorchedReplace the ATF and check the A/T
main unit and the vehicle for mal-
functions (wire harnesses, cooler
pipes, etc.)
Milky white or
cloudy Water in the fluidReplace the ATF and check for plac-
es where water is getting in.
Large amount of
metal powder mixed
in Unusual wear of
sliding parts within
A/T
Replace the ATF and check for im-
proper operation of the A/T.
SAT638A
SAT647B
SCIA7463E
Stall speed
VQ35DE engine: 2,650 - 2,950 rpm
VK45DE engine: 2,260 - 2,560 rpm
SAT514G
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-53
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Road TestINFOID:0000000001425855
DESCRIPTION
 The road test checks overall performance of the A/T and analyzes possible malfunction causes.
 The road test is carried out in the following three stages.
1. Check before engine is started.
2. Check at idle.
3. Cruise test
 Inspect all the items Part 1 to Part 3.
 Before beginning the road test, che ck the procedure and inspection items.
 Test all inspection items until the symptom is uncov ered. Diagnose NG items when all road tests are com-
plete.
CHECK BEFORE ENGINE IS STARTED
1.CHECK A/T CHECK INDICATOR LAMP
1. Park vehicle on level surface.
2. Move selector lever to “P” position.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
Does A/T CHECK indicator lamp light up for about 2 seconds?
YES - 1>> With CONSULT-III
1. Perform self-diagnostics and record all NG items on the “Diagnostic Worksheet Chart”.
2. Go to “CHECK AT IDLE”.
YES - 2>> Without CONSULT-III
1. Perform self-diagnostics and record all NG it ems on the “Diagnostic Worksheet Chart”. Refer
to AT-91, "
Diagnosis Procedure without CONSULT-III".
2. Go to “CHECK AT IDLE”.
NO >> Stop the road test and go to AT-170, "
A/T Check Indicator Lamp Does Not Come On".
CHECK AT IDLE
1.CHECK STARTING THE ENGINE
1. Park vehicle on level surface.
2. Move selector lever to “P” or “N” position.
3. Turn ignition switch OFF.
4. Start engine.
Does the engine start?
YES >> GO TO 2.
NO >> Stop the road test and go to AT-170, "
Engine Cannot Be Started in "P" or "N" Position".
Stall speedLine pressure does
not rise higher than
the line pressure for
idle.
Possible causes include a sensor malfunction or malfunction in the pressure adjustment function.
For example
 Accelerator pedal position signal malfunction
 TCM breakdown
 Line pressure solenoid malfunction (shorting, sticking in ON state)
 Pressure regulator valve or plug sticking
 Pilot valve sticking or pilot filter clogged
The pressure rises,
but does not enter
the standard posi-
tion. Possible causes include malfunctions in the pressure supply system and malfunction in the pres-
sure adjustment function.
For example
 Accelerator pedal position signal malfunction
 Line pressure solenoid malfunction (sticking, filter clog)
 Pressure regulator valve or plug sticking
 Pilot valve sticking or pilot filter clogged
Only low for a spe-
cific position Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
Judgement Possible cause
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C