lock INFINITI G37 2012 User Guide

Black plate (33,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0994
To lower, push and hold the lock knob and
push the head restraint down. SSS0995
Removal GUID-57DF10FD-7FAA-4FB1-8D61-CC400E811A0D
Use the following procedure to remove the
adjustable head restraints.
1. Pull the head restraint up to the highest
position.
2. Push and hold the lock knob.
3. Remove the head restraint from the
seat.
4. Store the head restraint properly in a
secure place so it is not loose in the
vehicle.
5. Reinstall and properly adjust the head
restraint before an occupant uses the seating position.
Safety — Seats, seat belts and supplemental restraint system
1-11

Black plate (34,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-12 Safety — Seats, seat belts and supplemental restraint system SSS0996
Install GUID-A0266381-3929-4791-B5F4-7F6C9A04687C
1. Align the head restraint stalks with the
holes in the seat. Make sure that the
head restraint is facing the correct
direction. The stalk with the adjustment
notches
* 1
must be installed in the
hole with the lock knob
* 2
.
2. Push and hold the lock knob and push
the head restraint down.
3. Properly adjust the head restraint
before an occupant uses the seating
position. SSS0508
Front-seat Active Head Restraints GUID-5D9BA25C-DA31-49D7-B3FB-9413B1B21746
The Active Head Restraint moves forward
utilizing the force that the seatback re-
ceives from the occupant in a rear-end
collision. The movement of the head
restraint helps support the occupant ’ s
head by reducing its backward movement
and helping absorb some of the forces that
may lead to whiplash-type injuries.
Active Head Restraints are effective for
collisions at low to medium speeds in
which it is said that whiplash-type injury
occurs most.
Active Head Restraints operate only in certain rear-end collisions. After the colli-
sion, the head restraints return to their
original positions.
Adjust the Active Head Restraints properly
as described earlier in this section.

Black plate (35,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0678
ARMREST (if so equipped) GUID-A816B76C-44C8-4E8F-8A10-1B4F0B8E76F2
Rear armrest GUID-61E1DB83-21E2-4B96-B569-EF340CDD6AC1
Pull the armrest forward until it is hor-
izontal. SSS0677
Trunk pass-through GUID-799B2734-1032-4868-BF9B-86682A7F09A9
The rear center seatback can be folded to
allow trunk access from inside of the
vehicle.
To access the trunk, pull down the rear
center armrest and pull out the trunk pass-
through lid
* 1
.
To lock the lid, use the mechanical key and
turn it to the LOCK position
* 3
. To unlock,
turn the mechanical key to the UNLOCK
position
* 2
. For the mechanical key usage,
see “ Keys ” (P.3-2).
Make sure that the mechanical key is
removed from the trunk pass-through lid key cylinder before opening or closing the
lid. Otherwise the lid and the rear armrest
may be damaged.
Safety — Seats, seat belts and supplemental restraint system
1-13

Black plate (39,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]seat with both feet on the floor and
adjust the seat belt properly.
. Do not allow children to play with the
seat belts. Most seating positions are
equipped with Automatic Locking Re-
tractor (ALR) mode seat belts. If the seat
belt becomes wrapped around a child ’ s
neck with the ALR mode activated, the
child can be seriously injured or killed if
the seat belt retracts and becomes tight.
This can occur even if the vehicle is
parked. Unbuckle the seat belt to release
the child. If the seat belt can not be
unbuckled or is already unbuckled,
release the child by cutting the seat belt
with a suitable tool (such as a knife or
scissors) to release the seat belt. SSS0292
Fastening the seat belts GUID-B37DD1F9-9FF6-46C4-80B5-F68C6BFB1F41
1. Adjust the seat. (See “ Seats ” (P.1-2).)
2. Slowly pull the seat belt out of the
retractor and insert the tongue into the
buckle until you hear and feel the latch
engage. .
The retractor is designed to lock
during a sudden stop or on impact.
A slow pulling motion permits the
belt to move, and allows you some
freedom of movement in the seat. .
If the seat belt cannot be pulled
from its fully retracted position,
firmly pull the belt and release it. Then smoothly pull the belt out of
the retractor.
Safety — Seats, seat belts and supplemental restraint system
1-17

Black plate (40,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-18 Safety — Seats, seat belts and supplemental restraint system SSS0290
3. Position the lap belt portion low and
snug on the hips as shown.
4. Pull the shoulder belt portion toward
the retractor to take up extra slack. Be
sure the shoulder belt is routed over
your shoulder and across your chest.
The three-point type seat belts have two
modes of operation:
. Emergency Locking Retractor (ELR)
. Automatic Locking Retractor (ALR)
The Emergency Locking Retractor (ELR)
mode allows the seat belt to extend and
retract to allow the driver and passengers
some freedom of movement in the seat. The ELR locks the seat belt when the
vehicle slows down rapidly or during
impacts.
The Automatic Locking Retractor (ALR)
mode (child restraint mode) locks the seat
belt for child restraint installation.
When the ALR mode is activated the seat
belt cannot be extended again until the
seat belt tongue is detached from the
buckle and fully retracted. The seat belt
returns to the ELR mode after the seat belt
fully retracts. For additional information,
see “ Child restraints ” (P.1-23).
The ALR mode should be used only for
child restraint installation. During normal
seat belt use by an occupant, the ALR
mode should not be activated. If it is
activated, it may cause uncomfortable seat
belt tension.
WARNING When fastening the seat belts, be certain
that seatbacks are completely secured in
the latched position. If they are not com-
pletely secured, passengers may be injured
in an accident or sudden stop. SSS0326
Unfastening the seat belts GUID-E5ABF433-63F1-41B4-9060-772462985B76
To unfasten the seat belt, push the button
on the buckle. The seat belt automatically
retracts.
Checking seat belt operation GUID-B2C3D22B-2FD8-46E0-9AC6-84735F785EB4
Seat belt retractors are designed to lock
seat belt movement by two separate
methods:
. When the belt is pulled quickly from the
retractor.
. When the vehicle slows down rapidly.
To increase your confidence in the seat
belts, check the operation as follows:

Black plate (41,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]. Grasp the shoulder belt and pull
forward quickly. The retractor should
lock and restrict further belt movement.
If the retractor does not lock during this
check or if you have any question about
seat belt operation, see an INFINITI retailer.
SSS0687
Center of rear seat (Sedan) GUID-F8C852B7-8F2B-4F66-B9F1-740AF287A7F1
Selecting correct set of seat belts: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The center seat belt buckle is identified by
the CENTER mark
* A
. The center seat belt
tongue can be fastened only into the center
seat belt buckle. SSS0294A
Shoulder belt height adjustment
(for Sedan front seats) GUID-9DA0069A-F53D-4536-89F5-3F6983A3F7DF
The shoulder belt anchor height should be
adjusted to the position best for you. (See
“ Precautions on seat belt usage ” (P.1-14).)
To adjust, push the button
* A
, and then
move the shoulder belt anchor to the
desired position, so that the belt passes
over the center of the shoulder. The belt
should be away from your face and neck,
but not falling off of your shoulder. Release
the adjustment button to lock the shoulder
belt anchor into position.
Safety — Seats, seat belts and supplemental restraint system
1-19

Black plate (42,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-20 Safety — Seats, seat belts and supplemental restraint systemWARNING. After adjustment, release the adjustment
button and try to move the shoulder belt
anchor up and down to make sure it is
securely fixed in position.
. The shoulder belt anchor height should
be adjusted to the position best for you.
Failure to do so may reduce the effec-
tiveness of the entire restraint system
and increase the chance or severity of
injury in an accident. SSS0588
Shoulder belt arm (for Coupe front
seats) GUID-79A89F1D-4AEA-49A3-B52A-98FCD811131B
Before fastening the seat belt, pull the
shoulder belt arm forward until it clicks at
the lock position. The arm can also be
folded down for easier access for rear seat
passengers.
Pulling the arm forward will allow an easy
access to the belt. SEAT BELT EXTENDERS GUID-B1D92F02-3294-412F-84BF-88F73FEF6097
If, because of body size or driving position,
it is not possible to properly fit the lap-
shoulder belt and fasten it, an extender
that is compatible with the installed seat
belts is available that can be purchased.
The extender adds approximately 8 in (200
mm) of length and may be used for either
the driver or front passenger seating
position. See an INFINITI retailer for assis-
tance with purchasing an extender if an
extender is required.
WARNING . Only INFINITI seat belt extenders, made
by the same company which made the
original equipment seat belts, should be
used with the INFINITI seat belts.
. Adults and children who can use the
standard seat belt should not use an
extender. Such unnecessary use could
result in serious personal injury in the
event of an accident.
. Never use seat belt extenders to install
child restraints. If the child restraint is
not secured properly, the child could be
seriously injured in a collision or a

Black plate (43,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]sudden stop.
SEAT BELT MAINTENANCE GUID-FD012A51-6217-44CA-9A47-C28EBAF61CDE
. To clean the seat belt webbing, apply a
mild soap solution or any solution
recommended for cleaning upholstery
or carpets. Then, wipe with a cloth and
allow the seat belts to dry in the shade.
Do not allow the seat belts to retract
until they are completely dry.
. If dirt builds up in the shoulder belt
guide of the seat belt anchors, the seat
belts may retract slowly. Wipe the
shoulder belt guide with a clean, dry
cloth.
. Periodically check to see that the seat
belt and the metal components such as
buckles, tongues, retractors, flexible
wires and anchors work properly. If
loose parts, deterioration, cuts or other
damage on the webbing is found, the
entire seat belt assembly should be
replaced. GUID-758C3ADB-56E4-4839-A833-17F0574CC784
WARNING Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child ’ s neck with the ALR
mode activated, the child can be seriously
injured or killed if the seat belt retracts and
becomes tight. This can occur even if the
vehicle is parked. Unbuckle the seat belt to
release the child. If the seat belt can not be
unbuckled or is already unbuckled, release
the child by cutting the seat belt with a
suitable tool (such as a knife or scissors) to
release the seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in
this manual, child safety information is
available from many other sources, includ-
ing doctors, teachers, government traffic
safety offices, and community organiza-
tions. Every child is different, so be sure to
learn the best way to transport your child.
There are three basic types of child
restraint systems: . Rear-facing child restraint
. Forward-facing child restraint
. Booster seat
The proper restraint depends on the child ’ s
size. Generally, infants up to about 1 year
and less than 20 lbs (9 kg) should be
placed in rear-facing child restraints. For-
ward-facing child restraints are available
for children who outgrow rear-facing child
restraints and are at least 1 year old.
Booster seats are used to help position a
vehicle lap/shoulder belt on a child who
can no longer use a forward-facing child
restraint.
WARNING Infants and children need special protection.
The vehicle ’ s seat belts may not fit them
properly. The shoulder belt may come too
close to the face or neck. The lap belt may
not fit over their small hip bones. In an
accident, an improperly fitting seat belt
could cause serious or fatal injury. Always
use appropriate child restraints.
All U.S. states and Canadian provinces or
territories require the use of approved
child restraints for infants and small
Safety — Seats, seat belts and supplemental restraint system
1-21CHILD SAFETY

Black plate (51,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]applicable). Not all child restraints fit in
all types of vehicles.
5. Check to make sure the child restraint
is properly secured prior to each use. If
the child restraint is loose, repeat steps
1 through 4.
SSS0100
REAR-FACING CHILD RESTRAINT IN-
STALLATION USING THE SEAT BELTS GUID-68D5DDB8-3F24-4C65-922C-6DD7B90A7477
WARNING The three-point seat belt with Automatic
Locking Retractor (ALR) must be used when
installing a child restraint. Failure to use the
ALR mode will result in the child restraint
not being properly secured. The restraint
could tip over or be loose and cause injury
to a child in a sudden stop or collision. Also,
it can change the operation of the front
passenger air bag. See “ Front passenger air bag and status light ” (P.1-49).
Safety — Seats, seat belts and supplemental restraint system
1-29

Black plate (52,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-30 Safety — Seats, seat belts and supplemental restraint system SSS0100
Rear-facing — step 1
Refer to all Warnings and Cautions in the
“ Child safety ” (P.1-21) and “ Child re-
straints ” (P.1-23) before installing a child
restraint.
Follow these steps to install a rear-facing
child restraint using the vehicle seat belts
in the rear seats:
1. Child restraints for infants must be
used in the rear-facing direction and
therefore must not be used in the front
seat. Position the child restraint on the
seat. Always follow the restraint man-
ufacturer ’ s instructions. SSS0654
Rear-facing — step 2
2. Route the seat belt tongue through the
child restraint and insert it into the
buckle until you hear and feel the latch
engage. Be sure to follow the child
restraint manufacturer ’ s instructions
for belt routing. SSS0655
Rear-facing — step 3
3. Pull the shoulder belt until the belt is
fully extended. At this time, the seat
belt retractor is in the Automatic Lock-
ing Retractor (ALR) mode (child restraint
mode). It reverts to the Emergency
Locking Retractor (ELR) mode when
the seat belt is fully retracted.