lock INFINITI G37 2012 Owner's Manual

Black plate (54,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-32 Safety — Seats, seat belts and supplemental restraint system7. Check to make sure that the child
restraint is properly secured prior to
each use. If the seat belt is not locked,
repeat steps 1 through 6.
After the child restraint is removed and the
seat belt fully retracted, the ALR mode
(child restraint mode) is canceled.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING LATCH GUID-C7CEB4CB-D6DD-4996-BA6E-023C4B2CA773
Refer to all Warnings and Cautions in the
“ Child safety ” and “ Child restraints ” sec-
tions before installing a child restraint.
Follow these steps to install a forward-
facing child restraint using the LATCH
system:
1. Position the child restraint on the seat.
Always follow the child restraint man-
ufacturer ’ s instructions. SSS0645
Forward-facing web-mounted — step 2
2. Secure the child restraint anchor at-
tachments to the LATCH lower anchors.
Check to make sure the LATCH attach-
ment is properly attached to the lower
anchors.
If the child restraint is equipped with a
top tether strap, route the top tether
strap and secure the tether strap to the
tether anchor point. See “ Installing top
tether strap ” (P.1-37). Do not install
child restraints that require the use of a
top tether strap in seating positions
that do not have a top tether anchor. SSS0646
Forward-facing rigid-mounted — step 3
3. The back of the child restraint should
be secured against the vehicle seat-
back.
If the seating position does not have an
adjustable headrest and it is interfering
with the proper child restraint fit, try
another seating position or a different
child restraint.

Black plate (55,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0647
Forward-facing — step 4
4. For child restraints that are equipped
with webbing-mounted attachments,
remove any additional slack from the
anchor attachments. Press downward
and rearward firmly in the center of the
child restraint with your knee to com-
press the vehicle seat cushion and
seatback while tightening the webbing
of the anchor attachments.
5. Tighten the tether strap according to
the manufacturer ’ s instructions to re-
move any slack. SSS0638
Forward-facing — step 6
6. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the LATCH attach-
ment path. The child restraint should
not move more than 1 inch (25 mm),
from side to side. Try to tug it forward
and check to see if the LATCH attach-
ment holds the restraint in place. If the
restraint is not secure, tighten the
LATCH attachment as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles. 7. Check to make sure the child restraint
is properly secured prior to each use. If
the child restraint is loose, repeat steps
1 through 6.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT
BELTS GUID-B0438CCC-C788-4E94-8FA4-DB4F26EE0A33
WARNING The three-point seat belt with Automatic
Locking Retractor (ALR) must be used when
installing a child restraint. Failure to use the
ALR mode will result in the child restraint
not being properly secured. The restraint
could tip over or be loose and cause injury
to a child in a sudden stop or collision. Also,
it can change the operation of the front
passenger air bag. See “ Front passenger air
bag and status light ” (P.1-49).
Safety — Seats, seat belts and supplemental restraint system
1-33

Black plate (57,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0651
Forward-facing — step 4
4. Pull the shoulder belt until the belt is
fully extended. At this time, the seat
belt retractor is in the Automatic Lock-
ing Retractor (ALR) mode (child restraint
mode). It reverts to Emergency Locking
Retractor (ELR) mode when the seat belt
is fully retracted. SSS0652
Forward-facing — step 5
5. Allow the seat belt to retract. Pull up on
the shoulder belt to remove any slack
in the belt. SSS0653
Forward-facing — step 6
6. Remove any additional slack from the
seat belt; press downward and rear-
ward firmly in the center of the child
restraint with your knee to compress
the vehicle seat cushion and seatback
while pulling up on the seat belt.
7. Tighten the tether strap according to
the manufacturer ’ s instructions to re-
move any slack.
Safety — Seats, seat belts and supplemental restraint system
1-35

Black plate (58,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-36 Safety — Seats, seat belts and supplemental restraint system SSS0641
Forward-facing — step 8
8. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the seat belt path.
The child restraint should not move
more than 1 inch (25 mm), from side to
side. Try to tug it forward and check to
see if the belt holds the restraint in
place. If the restraint is not secure,
tighten the seat belt as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles. 9. Check to make sure the child restraint
is properly secured prior to each use. If
the seat belt is not locked, repeat steps
2 through 8.
SSS0676
Forward-facing — step 10
10. If the child restraint is installed in the
front passenger seat, place the ignition
switch in the ON position. The front
passenger air bag status light
should illuminate. If this light is not
illuminated, see “ Front passenger air
bag and status light ” (P.1-49). Move
the child restraint to another seating
position. Have the system checked by
an INFINITI retailer.
After the child restraint is removed and the
seat belt is fully retracted, the ALR mode
(child restraint mode) is canceled.

Black plate (61,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]LRS0464
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated.
The instructions in this section apply to
booster seat installation in the rear seats
or the front passenger seat. Booster seat installation GUID-F402278F-CB4D-47C2-8CA5-E6E93C16F092
CAUTION Do not use the lap/shoulder belt Automatic
Locking Retractor (ALR) mode when using a
booster seat with the seat belts.
Refer to all Warnings and Cautions in the
“ Child safety ” , “ Child restraints ” and
“ Booster seats ” sections earlier in this
section before installing a child restraint.
Follow these steps to install a booster seat
in the rear seat or in the front passenger
seat: SSS0640
1. If you must install a booster seat in the
front seat, move the seat to the rear-
most position.
2. Position the booster seat on the seat.
Only place it in a forward-facing direc-
tion. Always follow the booster seat
manufacturer ’ s instructions.
Safety — Seats, seat belts and supplemental restraint system
1-39

Black plate (78,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-56 Safety — Seats, seat belts and supplemental restraint systemsystems will not operate in an accident. To
help avoid injury to yourself or others, have
your vehicle checked by a retailer as soon as
possible.
REPAIR AND REPLACEMENT PROCE-
DURE GUID-14E865CD-CF42-4FB6-85F1-2404D96FDE4E
The front air bags, side air bags, curtain air
bags and pretensioners are designed to
activate on a one-time-only basis. As a
reminder, unless it is damaged, the sup-
plemental air bag warning light will remain
illuminated after inflation has occurred.
Repair and replacement of these systems
should be done only by an INFINITI retailer.
When maintenance work is required on the
vehicle, the front air bags, side air bags,
curtain air bags, pretensioners and related
parts should be pointed out to the person
conducting the maintenance. The ignition
switch should always be in the LOCK
position when working under the hood or
inside the vehicle.
WARNING. Once a front air bag, side air bag, or
curtain air bag has inflated, the air bag module will not function again and must
be replaced. Additionally, the activated
pretensioner must also be replaced. The
air bag module and pretensioner should
be replaced by an INFINITI retailer. The
air bag module and pretensioner system
cannot be repaired.
. The front air bag, side air bag, curtain air
bag and the pretensioner system should
be inspected by an INFINITI retailer if
there is any damage to the front end or
side portion of the vehicle.
. If you need to dispose of the supple-
mental air bag or pretensioner or scrap
the vehicle, contact an INFINITI retailer.
Correct supplemental air bag and seat
belt pretensioner system disposal pro-
cedures are set forth in the appropriate
INFINITI Service Manual. Incorrect dis-
posal procedures could cause personal
injury.

Black plate (79,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2 Instruments and controls Cockpit ................................................................... 2-3
Instrument panel .................................................... 2-4
Meters and gauges ................................................. 2-6
Speedometer and odometer ............................... 2-7
Tachometer ......................................................... 2-8
Engine coolant temperature gauge ..................... 2-8
Fuel gauge ......................................................... 2-9
Compass (if so equipped) ....................................... 2-9
Zone variation change procedure ...................... 2-11
Warning/indicator lights and
audible reminders ................................................ 2-12
Checking bulbs ................................................. 2-12
Warning lights .................................................. 2-12
Indicator lights ................................................. 2-18
Audible reminders ............................................ 2-19
Dot matrix liquid crystal display ........................... 2-20
Indicators for operation .................................... 2-22
Indicators for maintenance ............................... 2-24
Trip computer ................................................... 2-26
Security systems .................................................. 2-28
Vehicle Security System ................................... 2-28
INFINITI Vehicle Immobilizer System ................. 2-30
Windshield wiper and washer switch .................... 2-31
Rain-sensing auto wiper system
(if so equipped) ................................................ 2-33 Rear window and outside mirror
defroster switch ................................................... 2-34
Headlight and turn signal switch .......................... 2-34
Xenon headlights ............................................ 2-34
Headlight switch ............................................. 2-35
Turn signal switch ........................................... 2-38
Fog light switch .............................................. 2-39
Hazard warning flasher switch ............................. 2-39
Horn .................................................................... 2-40
Heated seats (if so equipped) .............................. 2-40
SNOW mode switch (if so equipped) .................... 2-41
Vehicle Dynamic Control (VDC) OFF switch ............ 2-42
Clock .................................................................... 2-42
Adjusting the time .......................................... 2-42
Power outlet ........................................................ 2-43
Cigarette lighter and ashtrays (if so equipped) ....... 2-44
Front ............................................................... 2-44
Rear ................................................................ 2-44
Storage ................................................................ 2-45
Cup holders .................................................... 2-45
Sunglasses holder ......................................... 2-47
Glove box ....................................................... 2-47
Console box .................................................... 2-48
Card holder (if so equipped) ........................... 2-49
Storage box (if so equipped) ........................... 2-50>

Black plate (82,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-4 Instruments and controls GUID-F966D69B-15F8-48D0-A86B-A60F682B16E9
SSI0671
1. Side ventilator (P.4-30)
2. Meters and gauges (P.2-6)
3. Center ventilator (P.4-30)
4. Audio system (P.4-41)
5. Clock (P.2-42)
6. Center multi-function control panel — Navigation system* (if so
equipped)
— Vehicle information and setting
buttons (P.4-9)
— Bluetooth ®
Hands-Free Phone Sys-
tem (if so equipped) (P.4-90, P.4-100) — Audio system (P.4-41)
7. Center display (P.4-3)/Navigation sys-
tem* (if so equipped)
8. Hazard warning flasher switch (P.2-39)
9. Front passenger supplemental air bag
(P.1-41)
10. Fuse box cover (P.8-24)
11. Parking brake (for Automatic Trans-
mission models)
— Parking (P.5-20)
12. Push-button ignition switch (P.5-9)
13. Automatic climate control system
(P.4-31)
14. Cigarette lighter and ashtray (if so
equipped) (P.2-44) or storage box (if
so equipped) (P.2-50)
— Power outlet (if so equipped)
(P.2-43)
15. Parking brake (for Manual Transmis-
sion models)
— Parking (P.5-20)
16. Heated seat switch (if so equipped)
(P.2-40)
17. SNOW mode switch (if so equipped)
(P.2-41)
18. Rear window and outside mirror (if so
equipped) defroster switch (P.2-34)INSTRUMENT PANEL

Black plate (84,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-6 Instruments and controls GUID-50C93020-C345-4E0C-9F52-C7AB04736560
SIC4288
1. Tachometer (P.2-8)
2. Warning/Indicator lights (P.2-12)
3. Speedometer (P.2-7)
4. Engine coolant temperature gauge
(P.2-8)
5. Dot matrix liquid crystal display/ Odometer/twin trip odometer
(P.2-20)
6. Fuel gauge (P.2-9)
*: The needle indicators in the speed-
ometer, tachometer, engine coolant
temperature gauge and fuel gauge may move slightly after the ignition
switch is pushed to the LOCK posi-
tion. This is not a malfunction.
METERS AND GAUGES

Black plate (90,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-12 Instruments and controls GUID-4DFBC906-87A9-4F02-A005-17EFB9C1B112
All-Wheel Drive (AWD) warning light (AWD
models)* Intelligent Cruise Control (ICC) system
warning light (orange)* Exterior light indicator
Anti-lock Braking System (ABS) warning
light Intelligent Key warning light Front fog light indicator light
Low tire pressure warning light Front passenger air bag status light
Automatic transmission check warning light Master warning light High beam indicator light
Brake warning light Preview Function warning light (orange)* Malfunction Indicator Light (MIL)
Seat belt warning light Security indicator light
Charge warning light Supplemental air bag warning light Turn signal/hazard indicator lights
Engine oil pressure warning light Vehicle Dynamic Control (VDC) warning light Vehicle Dynamic Control (VDC) off indicator
light
4 Wheel Active Steer (4WAS) warning light* Automatic transmission position indicator
light* *: if so equipped
CHECKING BULBS GUID-EA46E715-CDC1-4316-A1CC-964FA500463C
With all doors closed, apply the parking
brake and push the ignition switch to the
ON position without starting the engine.
The following lights will come on (if so
equipped):
, or , , , , ,
The following lights come on briefly and
then go off (if so equipped):
, or , , , , ,
If any light does not come on, it may
indicate a burned-out bulb or an open circuit in the electrical system. Have the
system checked by an INFINITI retailer.
Some indicators and warnings are also
displayed on the dot matrix crystal display
between the speedometer and tachometer.
(See “ Dot matrix liquid crystal display ”
(P.2-20).) WARNING LIGHTS GUID-7D034C77-E122-4514-8406-A8ED72A0DDF7
All-Wheel Drive (AWD) warning
light (AWD models) (if so equipped) GUID-6272AC4F-020E-4475-8EA4-DEB8ABD3D971
The warning light comes on when the
ignition switch is pushed to ON. It turns off
soon after the engine is started.
If the AWD system malfunctions, or the
diameter of the front and the rear wheels
are different, the warning light will either
remain illuminated or blink. (See “ All-
Wheel Drive (AWD) ” (P.5-45).)WARNING/INDICATOR LIGHTS AND
AUDIBLE REMINDERS