ignition INFINITI G37 2012 Service Manual

Black plate (134,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-56 Instruments and controlsthe moonroof switch and release it; it need
not be held. The roof will automatically
open or close all the way. To stop the roof,
push the switch once more while it is
opening or closing.
Auto reverse function GUID-1665A219-159C-4E8B-97CC-F44A3889C13D
WARNINGThere are some small distances immediately
before the closed position which cannot be
detected. Make sure that all passengers
have their hands, etc., inside the vehicle
before closing the moonroof.
If the control unit detects something
caught in the moonroof when it is closing,
the moonroof will be immediately opened.
The auto reverse function can be activated
when the moonroof is closed by automatic
operation when the ignition switch is in the
ON position or for about 45 seconds after
the ignition switch is pushed to the OFF
position.
If the moonroof cannot be closed auto-
matically when the auto reverse function
activates due to a malfunction, push and
hold the CLOSE
* 1
side of the moonroof switch.
Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the moonroof
occurs.
If the moonroof does not operate GUID-235A4682-A88E-47F9-9907-4A08FACA91CE
If the moonroof does not operate properly,
perform the following procedure to initi-
alize the moonroof operation system.
1. If the moonroof is open, close it fully by
repeatedly pushing the CLOSE
* 1
side of the moonroof switch to tilt the
moonroof up.
2. Push and hold the CLOSE
* 1
side
of the moonroof switch.
3. Release the moonroof switch after the
moonroof moves slightly up and down.
4. Push and hold the OPEN
* 2
side of
the moonroof switch to fully tilt the
moonroof down.
5. Check if the moonroof switch operates
normally.
If the moonroof does not operate properly
after performing the procedure above, have
your vehicle checked by an INFINITI retailer. GUID-086B1CC9-F92B-4357-8461-A4FAC03B72E8
SIC3249
MAP LIGHTS GUID-1AFD655C-C54F-4694-ACBA-625EF6501A09
Push the button as illustrated to turn the
light on or off.INTERIOR LIGHTS

Black plate (135,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SIC3250
PERSONAL LIGHTS (Sedan) GUID-8A80AFCB-87B7-47AE-B03E-E39C7E1A6A4A
Rear GUID-CB368416-2E25-494C-922F-2408158FB064
Push the button as illustrated to turn the
light on or off. SIC3251
INTERIOR LIGHT CONTROL SWITCH GUID-C2DB58AC-6BD5-4108-8834-2A62D1E0B377
The interior light control switch has three
positions: ON, DOOR and OFF.
ON position GUID-798EF023-2D8A-44E2-8CE2-F22177A6EBE9
When the switch is in the ON position
* 1
the map lights and rear personal lights will
illuminate.
DOOR position GUID-CA87C080-730F-4193-BE23-19559113F670
When the switch is in the DOOR position
* 2
, the map lights and rear personal lights
will illuminate under the following condi-
tions: . ignition switch is switched to the LOCK
position
— remain on for about 15 seconds.
. doors are unlocked by pushing the
UNLOCK button on the Intelligent Key
or door handle request switch with the
ignition switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened and then closed
with the ignition switch in the LOCK
position
— remain on for about 15 seconds.
. any door is opened with the ignition
switch in the ACC or ON position
— remain on while the door is opened.
When the door is closed, the lights
go off.
The lights will also turn off after 15
minutes when the lights remain illumi-
nated after the ignition switch has been
pushed to the OFF or LOCK position to
prevent the battery from becoming dis-
charged.
When the auto interior illumination is set
to the OFF position (see “ Vehicle informa-
tion and settings ” (P.4-9)), the lights will
illuminate under the following condition:
Instruments and controls
2-57

Black plate (136,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-58 Instruments and controls. any door is opened with the ignition
switch in any position
— remain on while the door is opened.
When the door is closed, the lights
go off.
OFF position GUID-544F2395-1EF1-447D-9281-F30C0F022BEE
When the switch is in the OFF position
* 3
,
the lights will not illuminate, regardless of
the condition.
CAUTIONDo not use for extended periods of time with
the engine stopped. This could result in a
discharged battery. GUID-4767303A-3063-498C-B5AA-4C1CC218222A
SIC2064
Type A
SIC3869
Type B The light on the vanity mirror will turn on
when the cover on the vanity mirror is
opened.
When the cover is closed, the light will turn
off.
The lights will also turn off after 15
minutes when the lights remain illumi-
nated to prevent the battery from becom-
ing discharged.VANITY MIRROR LIGHTS

Black plate (137,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]GUID-3B0103FD-8C82-48ED-ABBE-0FF7FE9A8F16
The light illuminates when the trunk lid is
opened. When the trunk lid is closed, the
light will turn off.
The light will also turn off after 15 minutes
when the light remains illuminated after
the ignition switch has been pushed to the
OFF or LOCK position to prevent the
battery from becoming discharged. GUID-0BF67760-C562-4D9A-8217-C1A104712017
HomeLink ®
Universal Transceiver provides
a convenient way to consolidate the func-
tions of up to three individual hand-held
transmitters into one built-in device.
HomeLink ®
Universal Transceiver:
. Will operate most Radio Frequency (RF)
devices such as garage doors, gates,
home and office lighting, entry door
locks and security systems.
. Is powered by your vehicle ’ s battery. No
separate batteries are required. If the
vehicle ’ s battery is discharged or is
disconnected, HomeLink ®
will retain all
programming.
Once HomeLink ®
Universal Transceiver is
programmed, retain the original transmit-
ter for future programming procedures
(Example: new vehicle purchases). Upon
sale of the vehicle, the programmed
HomeLink ®
Universal Transceiver buttons
should be erased for security purposes.
For additional information, see “ Program-
ming HomeLink ®
” (P.2-60).
WARNING . Do not use HomeLink ®
Universal Trans-
ceiver with any garage door opener that
lacks safety stop and reverse features as required by federal safety standards.
(These standards became effective for
opener models manufactured after April
1, 1982.) A garage door opener which
cannot detect an object in the path of a
closing garage door and then automati-
cally stop and reverse, does not meet
current federal safety standards. Using a
garage door opener without these fea-
tures increases the risk of serious injury
or death.
. During programming procedure, your
garage door or security gate may open
or close. Make sure that people and
objects are clear of the garage door,
gate, etc. that you are programming.
. Your vehicle ’ s engine should be turned
off while programming HomeLink ®
Uni-
versal Transceiver.
Instruments and controls
2-59TRUNK LIGHT HomeLink ®
UNIVERSAL TRANSCEIVER (if so
equipped)

Black plate (148,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-6 Pre-driving checks and adjustmentsdoor, push the power door lock switch to
the unlock position
* 2
.
Lockout protection GUID-F17FC232-6651-4027-B680-5A82DB2977B3
When the power door lock switch (driver or
front passenger) is moved to the lock
position with the Intelligent Key in the port
and any door open, all doors will lock and
unlock automatically. With the Intelligent
Key left in the vehicle (not in the Intelligent
Key port) and any door open, all doors will
unlock automatically and a chime will
sound after the door is closed.
These functions help to prevent the In-
telligent Key from being accidentally
locked inside the vehicle.
AUTOMATIC DOOR LOCKS GUID-A10FB110-3B3F-40BA-97F3-3C215C27FFEF
. All doors lock automatically when the
vehicle speed reaches 15 MPH (24
km/h).
. All doors unlock automatically when the
ignition switch is placed in the OFF
position.
The automatic unlock function can be
deactivated or activated. To deactivate or
activate the automatic door unlock system,
perform the following procedure: 1. Close all doors.
2. Place the ignition switch in the ON
position.
3. Within 20 seconds of performing Step
2, push and hold the power door lock
switch to the
position (UNLOCK) for
more than 5 seconds.
4. When activated, the hazard indicator
will flash twice. When deactivated, the
hazard indicator will flash once.
5. The ignition switch must be placed in
the OFF and ON position again between
each setting change.
When the automatic door unlock system is
deactivated, the doors do not unlock when
the ignition switch is placed in the OFF
position. To unlock the door manually, use
the inside lock knob or the power door lock
switch (driver ’ s or front passenger ’ s side). SPA2470
CHILD SAFETY REAR DOOR LOCK
(Sedan) GUID-DE27EA42-B974-4087-AC65-39A603A3ECDA
The child safety rear door lock helps
prevent doors from being opened acciden-
tally, especially when small children are in
the vehicle.
When the levers are in the lock position
* 1
, the rear doors can be opened only
from the outside.
To disengage, move the levers to the
unlock position
* 2
.

Black plate (149,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]GUID-E775A3D7-CE8E-4FE0-9FB8-238232937EE5
WARNING. Radio waves could adversely affect
electric medical equipment. Those who
use a pacemaker should contact the
electric medical equipment manufacturer
for the possible influences before use.
. The Intelligent Key transmits radio
waves when the buttons are pushed.
The FAA advises that the radio waves
may affect aircraft navigation and com-
munication systems. Do not operate the
Intelligent Key while on an airplane.
Make sure the buttons are not operated
unintentionally when the unit is stored
during a flight.
The Intelligent Key system can operate all
the doors and the trunk lid using the
remote controller function or pushing the
request switch on the vehicle without
taking the key out from a pocket or purse.
The operating environment and/or condi-
tions may affect the Intelligent Key system
operation.
Be sure to read the following before using
the Intelligent Key system. CAUTION . Be sure to carry the Intelligent Key with
you when operating the vehicle.
. Never leave the Intelligent Key in the
vehicle when you leave the vehicle.
The Intelligent Key is always communicat-
ing with the vehicle as it receives radio
waves. The Intelligent Key system trans-
mits weak radio waves. Environmental
conditions may interfere with the operation
of the Intelligent Key system under the
following operating conditions.
. When operating near a location where
strong radio waves are transmitted,
such as a TV tower, power station and
broadcasting station.
. When in possession of wireless equip-
ment, such as a cellular telephone,
transceiver, and CB radio.
. When the Intelligent Key is in contact
with or covered by metallic materials.
. When any type of radio wave remote
control is used nearby.
. When the Intelligent Key is placed near
an electric appliance such as a perso- nal computer.
. When the vehicle is parked near a
parking meter.
In such cases, correct the operating condi-
tions before using the Intelligent Key
function or use the mechanical key.
Although the life of the battery varies
depending on the operating conditions,
the battery ’ s life is approximately 2 years.
If the battery is discharged, replace it with
a new one.
When the Intelligent Key battery is almost
discharged, insert the Intelligent Key into
the Intelligent Key port to start the engine.
Replace the discharged battery with a new
one as soon as possible. For more details,
see “ Push-button ignition switch ” (P.5-9).
Since the Intelligent Key is continuously
receiving radio waves, if the key is left near
equipment which transmits strong radio
waves, such as signals from a TV and
personal computer, the battery life may
become shorter.
For information regarding replacement of a
battery, see “ Intelligent Key battery repla-
cement ” (P.8-26).
As many as 4 Intelligent Keys can be
registered and used with one vehicle. For
Pre-driving checks and adjustments
3-7INTELLIGENT KEY SYSTEM

Black plate (152,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-10 Pre-driving checks and adjustments SPA2724
INTELLIGENT KEY OPERATION GUID-3067F87E-1F6D-40FB-85EF-BCAC29D5C466
You can lock or unlock the doors without
taking the key out from your pocket or bag. SPA2725
When you carry the Intelligent Key with
you, you can lock or unlock all doors by
pushing the door handle request switch
(driver ’ s or front passenger ’ s)
* A
within
the range of operation.
When you lock or unlock the doors or the
trunk lid, the hazard indicator will flash
and the horn (or the outside chime) will
sound as a confirmation. For details, see
“ Setting hazard indicator and horn mode ”
(P.3-16).
Locking doors and fuel-filler door GUID-63A62F2A-B46B-430A-A607-E006161B0ABE
1. Push the ignition switch to the OFF
position and make sure you carry the Intelligent Key with you.*1
2. Close all the doors.*2
3. Push the door handle request switch
(driver ’ s or front passenger ’ s)
* A
while
carrying the Intelligent Key with you.*3
4. All the doors and fuel-filler door will
lock.
5. The hazard indicator flashes twice and
the outside chime sounds twice.
*1: Doors will lock with the Intelligent Key
while the ignition switch is in the ACC or
ON position.
*2: Doors will not lock with the Intelligent
Key while any door is open.
*3: Doors will not lock by pushing the door
handle request switch with the Intelligent
Key inside the vehicle. However, when an
Intelligent Key is inside the vehicle, doors
can be locked with another registered
Intelligent Key.
CAUTION . After locking the doors using the request
switch, make sure that the doors have
been securely locked by operating the
door handles.

Black plate (153,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]. When locking the doors using the
request switch, make sure to have the
Intelligent Key in your possession before
operating the request switch to prevent
the Intelligent Key from being left in the
vehicle.
. The request switch is operational only
when the Intelligent Key has been
detected by the Intelligent Key system.
Lockout protection: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
To prevent the Intelligent Key from being
accidentally locked in the vehicle, lockout
protection is equipped with the Intelligent
Key system.
When the driver ’ s side door is open, the
doors are locked, and then the Intelligent
Key is put inside the vehicle and all the
doors are closed; the lock will automati-
cally unlock and the door buzzer sounds.
NOTE:
The doors may not lock when the Intelli-
gent Key is in the same hand that is
operating the request switch to lock the
door. Put the intelligent key in a purse,
pocket or your other hand. CAUTION The lockout protection may not function
under the following conditions:
. When the Intelligent Key is placed on top
of the instrument panel.
. When the Intelligent Key is placed inside
the glove box or a storage bin.
. When the Intelligent Key is placed inside
the door pockets.
. When the Intelligent Key is placed inside
or near metallic materials.
Unlocking doors and fuel-filler door GUID-AC9351D5-02D3-4448-8DA4-BC429212F8E4
1. Push the door handle request switch
(driver ’ s or front passenger ’ s)
* A
once
while carrying the Intelligent Key with
you.
2. The hazard indicator flashes once and
outside chime sounds once. The corre-
sponding door and the fuel-filler door
will unlock.
3. Push the door handle request switch
again within 1 minute.
4. The hazard indicator flashes once and
outside chime sounds once again. All the doors will unlock.
All doors and the fuel-filler door will be
locked automatically unless one of the
following operations is performed within 1
minute after pushing the request switch
while the doors are locked.
. Opening any door
. Pushing the ignition switch
. Inserting the Intelligent Key into the
Intelligent Key port.
During this 1-minute time period, if the
UNLOCK
button on the Intelligent Key
is pushed, all doors will be locked auto-
matically after another 1 minute.
Pre-driving checks and adjustments
3-11

Black plate (154,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-12 Pre-driving checks and adjustments JVP0077X
SPA2324
Sedan SPA2404
Coupe
Opening trunk lid GUID-8CAC547B-02BB-4FF9-92E6-7281A6D2F40E
1. Push the trunk open request switch
* A
for more than 1 second.
2. The trunk will unlatch. An outside
chime will sound four times.
3. Raise the trunk lid to open the trunk.
Lockout protection: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
To prevent the Intelligent Key from being
accidentally locked in the trunk, lockout
protection is equipped with the Intelligent
Key system.
When the trunk lid is closed with the
Intelligent Key inside the trunk, the outside chime will sound and the trunk will open.
BATTERY SAVER SYSTEM GUID-87E6AD4D-E5E1-4DF0-9F8D-89D71C40D4AA
When all the following conditions are met
for 60 minutes, the battery saver system
will cut off the power supply to prevent
battery discharge.
. The ignition switch is in the ACC
position, and
. All doors are closed, and
. The selector lever is in the P (Park)
position (Automatic Transmission mod-
els).
WARNING SIGNALS GUID-40E3A686-E7C6-4718-82C0-51E40924B2FE
To help prevent the vehicle from moving
unexpectedly by erroneous operation of
the Intelligent Key listed on the following
chart or to help prevent the vehicle from
being stolen, chime or beep sounds inside
and outside the vehicle and a warning
displays in the dot matrix liquid crystal
display.
When a chime or beep sounds or the
warning displays, be sure to check the
vehicle and Intelligent Key.
See “ Troubleshooting guide ” (P.3-13) and
“ Dot matrix liquid crystal display ” (P.2-20).

Black plate (155,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]TROUBLESHOOTING GUIDE GUID-74EA3136-2453-48A5-9A65-B4F622B666A0
Symptom Possible cause Action to take
When pushing the ignition switch
to stop the engine The SHIFT P warning appears on the display
and the inside warning chime sounds con-
tinuously (Automatic Transmission models). The selector lever is not in the P (Park)
position. Shift the selector lever to the P (Park)
position.
When shifting the selector lever
to the P (Park) position. The inside warning chime sounds continu-
ously. The ignition switch is in the ACC or ON
position. Push the ignition switch to the OFF position.
When opening the driver ’ s door to
get out of the vehicle The inside warning chime sounds continu-
ously. The ignition switch is in the ACC
position. Push the ignition switch to the OFF position.
The Intelligent Key is in the Intelligent
Key port. Remove the Intelligent Key from the Intel-
ligent Key port.
When closing the door after get-
ting out of the vehicle The NO KEY warning appears on the display,
the outside chime sounds 3 times and the
inside warning chime sounds for a few
seconds. The ignition switch is in the ACC or ON
position. Push the ignition switch to the OFF position.
The SHIFT P warning appears on the display
and the outside chime sounds continuously
(Automatic Transmission models). The ignition switch is in the ACC or OFF
position and the selector lever is not in
the P (Park) position. Move the selector lever to the P (Park)
position and push the ignition switch to the
OFF position.
When closing the door with the
inside lock knob turned to LOCK The outside chime sounds for a few seconds
and all the doors unlock. The Intelligent Key is inside the vehicle
or trunk. Carry the Intelligent Key with you.
When pushing the request switch
or LOCK button on the Intelligent
Key to lock the door The outside chime sounds for a few seconds. The Intelligent Key is inside the vehicle
or trunk. Carry the Intelligent Key with you.
A door is not closed securely. Close the door securely.
When closing the trunk lid The outside chime sounds for approximately
10 seconds and the trunk lid opens. The Intelligent Key is inside the trunk. Carry the Intelligent Key with you.
Pre-driving checks and adjustments
3-13