pressure INFINITI M35 2006 Factory Service Manual

QUICK REFERENCE CHART M35/M45
QUICK REFERENCE CHART M35/M45PFP:00000
ENGINE TUNE-UP DATA (VQ35DE)ELS0003W
Engine modelVQ35DE
Firing order1-2-3-4-5-6
Idle speed
A/T (In “P” or “N” position)rpm
650 ± 50
Ignition timing (BTDC at idle speed)
A/T (In “P” or “N” position)15
± 5
CO% at idle 0.7 - 9.9% and engine runs smoothly
Drive BeltDeflection adjustment Unit: mm (in) Tension adjustment Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
Limit After adjustment Limit After adjustment
Alternator and power
steering oil pump belt7 (0.28)4 - 5
(0.16 - 0.20)3.5 - 4.5
(0.138 - 0.177)294 (30, 66)730 - 818
(74.5 - 83.5,
164 - 184)838 - 926
(85.5 - 94.5,
188 - 208)
A/C compresor belt 12 (0.47)9 - 10
(0.35 - 0.39)8 - 9
(0.31 - 0.35)196 (20, 44)348 - 436
( 35.5 - 44.5,
78 - 98)470 - 559
( 4 8 - 5 7 ,
106 - 126)
Applied pushing force 98N (10kg, 22lb) —
Radiator cap relief pressure
kPa (kg/cm
2 , psi)
Standard 78 - 98 (0.8 - 1.0, 11 - 14)
Limit 59 (0.6, 9)
Cooling system leakage testing pres-
surekPa (kg/cm
2 , psi)157 (1.6, 23)
Compression pressure
kPa (kg/cm
2 , psi)/rpm
Standard 1,275 (13.0, 185) /300
Minimum 981 (10.0, 142) /300
Spark plug Standard type PLFR5A-11
Hot type PLFR4A-11
Cold type PLFR6A-11
2006

QUICK REFERENCE CHART M35/M45
ENGINE TUNE-UP DATA (VK45DE)
FRONT WHEEL ALIGNMENT (Unladen* )
ELS0003X
Engine modelVK45DE
Firing order1-8-7-3-6-5-4-2
Idle speed
A/T (In “P” or “N” position) rpm650
50
Ignition timing
(BTDC at idle speed)12
5
CO% at idle 0.7 - 9.9% and engine runs smoothly
Tensions of drive belts Auto adjustment by auto tensioner
Radiator cap relief pressure
kPa (kg/cm
2 , psi)
7 8 - 98 (0.8 - 1.0 , 11 - 14) Standard
Limit 59 (0.6, 9)
Cooling system leakage testing pressure
157 (1.6, 23)
kPa (kg/cm
2 , psi)
Compression pressure
kPa (kg/cm
2 , psi)/rpm
1,320 (13.5, 191) /300 Standard
Minimum 1,130 (11.5, 164) /300
Spark plug Standard type PLFR5A-11
Hot type PLFR4A-11
Cold type PLFR6A-11
Axle2WD AWD
Tire P245/45R18 245/40R19 245/45R18
Camber
Degree minute (Decimal degree)Minimum – 1
00 (– 1.00)
Nominal – 0
15 (– 0.25)
Maximum 0
30 (0.50)
Left and right difference 33
(0.55) or less
Caster
Degree minute (Decimal degree)Minimum 3
45 ( 3.75 ) 3 50 (3.83)3 05 ( 3.08 )
Nominal 4
30 ( 4.50 ) 4 35 (4.58)3 50 ( 3.83 )
Maximum 5
15 ( 5.25 ) 5 20 (5.33)4 35 ( 4.58 )
Left and right difference 39
(0.65) or less
Kingpin inclination
Degree minute (Decimal degree)Minimum 6
30 (6.50)
Nominal 7
15 (7.25)
Maximum 8
00 (8.00)
Total toe-inDistance (A – B)Minimum 0 mm (0 in)
Nominal 1 mm (0.04 in)
Maximum 2 mm (0.08 in)
Angle (left plus right)
Degree minute
(Degree)Minimum 0
(0)
Nominal 3
(0.05)
Maximum 6
(0.10)
2006

ACS-6
[ICC]
DESCRIPTION
Revision: 2006 January2006 M35/M45
DESCRIPTIONPFP:00000
OutlineNKS004CF
The Intelligent Cruise Control (ICC) system automatically maintains a selected distance from the vehicle
ahead according to that vehicle's speed, or at the set speed, if the road ahead is clear.
The ICC function has two cruise control modes and brake assist (with preview function).
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
Vehicle-to-vehicle distance control mode, the driver can maintain the same speed as other vehicles without
the constant need to adjust the set speed as the driver would with a normal cruise control system.
The system is intended to enhance the operation of the vehicle when following the vehicle traveling in the
same lane and direction.
If the ICC sensor integrated unit detects a slower moving vehicle ahead, the system will reduce speed so that
the vehicle ahead can be followed at the selected distance.
The system automatically controls the throttle and applies the brakes (up to 25% of vehicle braking power) if
necessary.
The detection range of the sensor is approximately 390 ft (120 m) ahead.
Refer to Owner's Manual for Intelligent Cruise Control System operating instructions.
CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE
Conventional (fixed speed) cruise control mode is cruising at preset speeds.
Refer to Owner's Manual for Intelligent Cruise Control System operating instructions.
BRAKE ASSIST (WITH PREVIEW FUNCTION)
When the force applied to brake pedal exceeds a certain level, the Brake Assist is activated and generates a
greater braking force than that of a conventional brake booster even with light pedal force.
When the Preview Function identifies the need to apply the sudden brake by sensing the vehicle ahead in the
same lane and the distance and relative speed from it, it applies the brake pre-pressure before driver
depresses the brake pedal and improves brake response by reducing its free play.
Refer to Owner's Manual for BRAKE ASSIST (WITH PREVIEW FUNCTION) operating instructions.
System DiagramNKS004CG
PKIB8345E

DESCRIPTION
ACS-7
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2006 January2006 M35/M45
Components DescriptionNKS004CH
CAN CommunicationNKS004CI
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tric control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN COMMUNICATION UNIT
Refer to LAN-34, "CAN Communication Unit" .
ComponentVehicle-to-
vehicle
distance
control modeConventional
(fixed speed)
cruise
control modeBrake assist
(with pre-
view func-
tion)Description
ICC sensor integrated unit
Controls vehicle distance by operating electric throttle
control actuator based on that sensor signals and
CAN communication data.
Controls vehicle distance by transmitting deceleration
degree commandment value signal to ABS actuator
and electric unit (control unit) when deceleration with
brake is needed.
Irradiates laser beam, and receives reflected laser
beam to measure distance from preceding vehicle.
ECM
Transmits accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal and ICC steering
switch signal to ICC sensor integrated unit through CAN
communication.
ABS actuator and electric
unit (control unit)
Transmits vehicle speed signal (wheel speed) and
stop lamp switch signal to ICC sensor integrated unit
through CAN communication.
Receives Deceleration degree commandment value
signal from ICC sensor integrated unit, and controls
brake fluid pressure with the ABS motor.
BCM
Transmits front wiper request signal to ICC sensor inte-
grated unit through CAN communication.
TCM
Transmits gear position signal and output shaft revolu-
tion signal to ICC sensor integrated unit through CAN
communication.
Unified meter and A/C amp.
Receives meter display signal, ICC warning lamp signal
and buzzer output signal from ICC sensor integrated
unit through CAN communication.
ICC brake switch
Transmits operating signal to ECM when depressing
brake pedal. ICC sensor integrated unit cancels cruise
system at driver's brake operation.
Stop lamp switch
Transmits operating signal to ECM and ABS actuator
and electric unit (control unit) when depressing brake
pedal. ICC sensor integrated unit cancels cruise system
at driver's brake operation.

LASER BEAM AIMING ADJUSTMENT
ACS-13
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2006 January2006 M35/M45
LASER BEAM AIMING ADJUSTMENTPFP:00026
OutlineNKS004CM
Adjust the laser beam aiming every time the ICC sensor integrated unit is removed or installed.
CAUTION:
Adjust laser beam aiming at a horizontal place as far as 12 m (39 ft) forward the vehicle can be
seen.
Adjust laser beam aiming 5 seconds after starting engine.
Never view ICC sensor integrated unit body window directly during laser beam aiming adjustment.
Follow the CONSULT-II when adjusting the laser beam aiming (laser beam aiming adjustment can-
not be operated without CONSULT-II).
Never ride on vehicle during laser beam aiming adjustment.
Idle and turn headlamps OFF during laser beam aiming adjustment.
PreparationNKS004CN
Adjust the tire pressure to the specified value.
See that there is no load in the vehicle.
Coolant, engine oil filled up to correct level and full fuel tank.
Shift the gear into “P” position and release the parking brake.
Clean the ICC sensor integrated unit with a soft cloth.
Remove the front bumper grille. Refer to EI-13, "Removal and
Installation of Front Bumper Grille" .
Outline of Adjustment ProcedureNKS004CO
1. Set up the ICC target board [KV99110100 (J-45718)].
2. Adjust the sensor following the procedure on CONSULT-II. (Turn manually the screw for up-down position
adjustment. ICC sensor integrated unit automatically adjust the right-left position.)
Setting the ICC Target BoardNKS004CP
Accurate ICC target board setting is required for the laser beam aiming adjustment.
CAUTION:
ICC system does not function normally if laser beam aiming is not accurate.
ADJUSTING HEIGHT OF THE TARGET
1. Attach a triangle scale at 28 mm (1.10 in) below the center.
PKIB8350E
PKIB8351E

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION AT
A
B
AT
Revision: 2006 January2006 M35/M45
AUTOMATIC TRANSMISSION
INDEX FOR DTC ........................................................ 5
Alphabetical Index .................................................... 5
DTC No. Index ......................................................... 6
PRECAUTIONS .......................................................... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine .................................................... 7
Precautions .............................................................. 8
Service Notice or Precautions .................................. 9
PREPARATION ......................................................... 10
Special Service Tools ............................................. 10
Commercial Service Tools ....................................... 11
A/T FLUID ................................................................. 12
Changing A/T Fluid .............................................
... 12
Checking A/T Fluid ................................................. 13
A/T Fluid Cooler Cleaning ...................................... 14
A/T CONTROL SYSTEM .......................................... 17
Cross-Sectional View (VQ35DE Models for 2WD) ... 17
Cross-Sectional View (VK45DE Models for 2WD) ... 18
Cross-Sectional View (AWD Models) ..................... 19
Shift Mechanism ..................................................... 20
TCM Function ......................................................... 31
CAN Communication .............................................. 32
Input/Output Signal of TCM .................................... 32
Line Pressure Control ............................................ 33
Shift Control ........................................................... 34
Lock-up Control ...................................................... 37
Engine Brake Control ............................................. 38
Control Valve .......................................................... 38
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 40
Introduction ............................................................ 40
OBD-II Function for A/T System ............................. 40
One or Two Trip Detection Logic of OBD-II ............ 40
OBD-II Diagnostic Trouble Code (DTC) ................. 40
Malfunction Indicator Lamp (MIL) ........................... 43
TROUBLE DIAGNOSIS ............................................ 44
DTC Inspection Priority Chart ................................ 44
Fail-safe ................................................................. 44How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 46
A/T Electrical Parts Location .................................. 51
Circuit Diagram ....................................................... 52
Inspections before Trouble Diagnosis .................... 53
Check before Engine Is Started .............................. 57
Check at Idle ........................................................... 57
Cruise Test - Part 1 ................................................. 59
Cruise Test - Part 2 ................................................. 61
Cruise Test - Part 3 ................................................. 62
Vehicle Speed at Which Gear Shifting Occurs ....... 63
Vehicle Speed at Which Lock-Up Occurs/Releases ... 63
Symptom Chart ....................................................... 64
TCM Input/Output Signal Reference Values ........... 89
CONSULT-II Function (A/T) .................................... 90
Diagnostic Procedure without CONSULT-II ..........103
DTC U1000 CAN COMMUNICATION LINE ............105
Description ............................................................105
On Board Diagnosis Logic ....................................105
Possible Cause .....................................................105
DTC Confirmation Procedure ...............................105
Wiring Diagram — AT — CAN ..............................106
Diagnostic Procedure ...........................................107
DTC P0615 START SIGNAL CIRCUIT ...................108
Description ............................................................108
CONSULT-II Reference Value ..............................108
On Board Diagnosis Logic ....................................108
Possible Cause .....................................................108
DTC Confirmation Procedure ...............................108
Wiring Diagram — AT — STSIG ..........................109
Diagnostic Procedure ...........................................110
DTC P0700 TCM .....................................................112
Description ............................................................112
On Board Diagnosis Logic ....................................112
Possible Cause .....................................................112
DTC Confirmation Procedure ...............................112
Diagnostic Procedure ...........................................112
DTC P0705 PARK/NEUTRAL POSITION SWITCH .113
Description ............................................................113
CONSULT-II Reference Value ..............................113

AT-2Revision: 2006 January2006 M35/M45 On Board Diagnosis Logic ....................................113
Possible Cause .....................................................113
DTC Confirmation Procedure ...............................113
Wiring Diagram — AT — PNP/SW .......................114
Diagnostic Procedure ...........................................115
DTC P0717 TURBINE REVOLUTION SENSOR ....117
Description ............................................................117
CONSULT-II Reference Value ..............................117
On Board Diagnosis Logic ....................................117
Possible Cause .....................................................117
DTC Confirmation Procedure ...............................117
Diagnostic Procedure ...........................................118
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) ...............................................119
Description ............................................................119
CONSULT-II Reference Value ..............................119
On Board Diagnosis Logic ....................................119
Possible Cause .....................................................119
DTC Confirmation Procedure ...............................119
Wiring Diagram — AT — VSSA/T .........................121
Diagnostic Procedure ...........................................122
DTC P0725 ENGINE SPEED SIGNAL ...................124
Description ............................................................124
CONSULT-II Reference Value ..............................124
On Board Diagnosis Logic ....................................124
Possible Cause .....................................................124
DTC Confirmation Procedure ...............................124
Diagnostic Procedure ...........................................125
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................126
Description ............................................................126
CONSULT-II Reference Value ..............................126
On Board Diagnosis Logic ....................................126
Possible Cause .....................................................126
DTC Confirmation Procedure ...............................126
Diagnostic Procedure ...........................................127
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) . 128
Description ............................................................128
CONSULT-II Reference Value ..............................128
On Board Diagnosis Logic ....................................128
Possible Cause .....................................................128
DTC Confirmation Procedure ...............................128
Diagnostic Procedure ...........................................129
DTC P0745 LINE PRESSURE SOLENOID VALVE .130
Description ............................................................130
CONSULT-II Reference Value ..............................130
On Board Diagnosis Logic ....................................130
Possible Cause .....................................................130
DTC Confirmation Procedure ...............................130
Diagnostic Procedure ...........................................131
DTC P1705 THROTTLE POSITION SENSOR .......132
Description ............................................................132
CONSULT-II Reference Value ..............................132
On Board Diagnosis Logic ....................................132
Possible Cause .....................................................132
DTC Confirmation Procedure ...............................132
Diagnostic Procedure ...........................................133
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ..................................................................135Description ............................................................135
CONSULT-II Reference Value ...............................135
On Board Diagnosis Logic ....................................135
Possible Cause .....................................................135
DTC Confirmation Procedure ................................135
Wiring Diagram — AT — FTS ...............................136
Diagnostic Procedure ............................................137
Component Inspection ..........................................139
DTC P1721 VEHICLE SPEED SENSOR MTR .......140
Description ............................................................140
CONSULT-II Reference Value ...............................140
On Board Diagnosis Logic ....................................140
Possible Cause .....................................................140
DTC Confirmation Procedure ................................140
Diagnostic Procedure ............................................141
DTC P1730 A/T INTERLOCK .................................142
Description ............................................................142
On Board Diagnosis Logic ....................................142
Possible Cause .....................................................142
DTC Confirmation Procedure ................................142
Judgement of A/T Interlock ...................................143
Diagnostic Procedure ............................................143
DTC P1731 A/T 1ST ENGINE BRAKING ...............145
Description ............................................................145
CONSULT-II Reference Value ...............................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ................................145
Diagnostic Procedure ............................................146
DTC P1752 INPUT CLUTCH SOLENOID VALVE ..147
Description ...................................................
.........147
CONSULT-II Reference Value ...............................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ................................147
Diagnostic Procedure ............................................148
DTC P1754 INPUT CLUTCH SOLENOID VALVE
FUNCTION ..............................................................149
Description ............................................................149
CONSULT-II Reference Value ...............................149
On Board Diagnosis Logic ....................................149
Possible Cause .....................................................149
DTC Confirmation Procedure ................................149
Diagnostic Procedure ............................................150
DTC P1757 FRONT BRAKE SOLENOID VALVE ...151
Description ............................................................151
CONSULT-II Reference Value ...............................151
On Board Diagnosis Logic ....................................151
Possible Cause .....................................................151
DTC Confirmation Procedure ................................151
Diagnostic Procedure ............................................152
DTC P1759 FRONT BRAKE SOLENOID VALVE
FUNCTION ..............................................................153
Description ............................................................153
CONSULT-II Reference Value ...............................153
On Board Diagnosis Logic ....................................153
Possible Cause .....................................................153
DTC Confirmation Procedure ................................153
Diagnostic Procedure ............................................154

AT-3
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2006 January2006 M35/M45 DTC P1762 DIRECT CLUTCH SOLENOID VALVE .155
Description ...........................................................155
CONSULT-II Reference Value ..............................155
On Board Diagnosis Logic ...................................155
Possible Cause ....................................................155
DTC Confirmation Procedure ...............................155
Diagnostic Procedure ...........................................156
DTC P1764 DIRECT CLUTCH SOLENOID VALVE
FUNCTION ..............................................................157
Description ...........................................................157
CONSULT-II Reference Value ..............................157
On Board Diagnosis Logic ...................................157
Possible Cause ....................................................157
DTC Confirmation Procedure ...............................157
Diagnostic Procedure ...........................................158
DTC P1767 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE .................................................159
Description ...........................................................159
CONSULT-II Reference Value ..............................159
On Board Diagnosis Logic ...................................159
Possible Cause ....................................................159
DTC Confirmation Procedure ...............................159
Diagnostic Procedure ...........................................160
DTC P1769 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE FUNCTION .............................161
Description ...........................................................161
CONSULT-II Reference Value ..............................161
On Board Diagnosis Logic ...................................161
Possible Cause ....................................................161
DTC Confirmation Procedure ...............................161
Diagnostic Procedure ...........................................162
DTC P1772 LOW COAST BRAKE SOLENOID
VALVE .....................................................................163
Description ...........................................................163
CONSULT-II Reference Value ..............................163
On Board Diagnosis Logic ...................................163
Possible Cause ....................................................163
DTC Confirmation Procedure ...............................163
Diagnostic Procedure ...........................................164
DTC P1774 LOW COAST BRAKE SOLENOID
VALVE FUNCTION .................................................165
Description ...........................................................165
CONSULT-II Reference Value ..............................165
On Board Diagnosis Logic ...................................165
Possible Cause ....................................................165
DTC Confirmation Procedure ...............................165
Diagnostic Procedure ..........................................
.166
DTC P1815 MANUAL MODE SWITCH ..................167
Description ...........................................................167
CONSULT-II Reference Value ..............................167
On Board Diagnosis Logic ...................................167
Possible Cause ....................................................167
DTC Confirmation Procedure ...............................167
Wiring Diagram — AT — MMSW .........................168
Diagnostic Procedure ...........................................170
Component Inspection .........................................171
DTC P1841 ATF PRESSURE SWITCH 1 ...............172
Description ...........................................................172
CONSULT-II Reference Value ..............................172On Board Diagnosis Logic ....................................172
Possible Cause .....................................................172
DTC Confirmation Procedure ...............................172
Diagnostic Procedure ...........................................173
DTC P1843 ATF PRESSURE SWITCH 3 ...............174
Description ............................................................174
CONSULT-II Reference Value ..............................174
On Board Diagnosis Logic ....................................174
Possible Cause .....................................................174
DTC Confirmation Procedure ...............................174
Diagnostic Procedure ...........................................175
DTC P1845 ATF PRESSURE SWITCH 5 ...............176
Description ............................................................176
CONSULT-II Reference Value ..............................176
On Board Diagnosis Logic ....................................176
Possible Cause .....................................................176
DTC Confirmation Procedure ...............................176
Diagnostic Procedure ...........................................177
DTC P1846 ATF PRESSURE SWITCH 6 ...............178
Description ............................................................178
CONSULT-II Reference Value ..............................178
On Board Diagnosis Logic ....................................178
Possible Cause .....................................................178
DTC Confirmation Procedure ...............................178
Diagnostic Procedure ...........................................179
MAIN POWER SUPPLY AND GROUND CIRCUIT .180
Wiring Diagram — AT — MAIN ............................180
Diagnostic Procedure ...........................................181
CLOSED THROTTLE POSITION AND WIDE OPEN
THROTTLE POSITION CIRCUIT ............................184
CONSULT-II Reference Value ..............................184
Diagnostic Procedure ...........................................184
BRAKE SIGNAL CIRCUIT ......................................185
CONSULT-II Reference Value ..............................185
Diagnostic Procedure ...........................................185
A/T INDICATOR CIRCUIT .......................................186
Description ............................................................186
CONSULT-II Reference Value ..............................186
Diagnostic Procedure ...........................................186
TROUBLE DIAGNOSIS FOR SYMPTOMS ............187
Wiring Diagram — AT — NONDTC ......................187
A/T CHECK Indicator Lamp Does Not Come On . 190
Engine Cannot Be Started in “P” or “N” Position ..190
In “P” Position, Vehicle Moves When Pushed ......191
In “N” Position, Vehicle Moves ..............................192
Large Shock (“N” to “D” Position) .........................193
Vehicle Does Not Creep Backward in “R” Position .195
Vehicle Does Not Creep Forward in “D” Position . 197
Vehicle Cannot Be Started from D
1 ......................199
A/T Does Not Shift: D
1 D2 ................................201
A/T Does Not Shift: D
2 D3 ................................203
A/T Does Not Shift: D
3 D4 ................................205
A/T Does Not Shift: D
4 D5 ................................207
A/T Does Not Lock-Up ..........................................209
A/T Does Not Hold Lock-Up Condition .................210
Lock-Up Is Not Released ......................................212
Engine Speed Does Not Return to Idle ................212
Cannot Be Changed to Manual Mode ..................213
A/T Does Not Shift: 5th Gear
4th Gear ............214

AT-4Revision: 2006 January2006 M35/M45 A/T Does Not Shift: 4th Gear
3rd Gear ............215
A/T Does Not Shift: 3rd Gear
2nd Gear ...........217
A/T Does Not Shift: 2nd Gear
1st Gear ............218
Vehicle Does Not Decelerate by Engine Brake ....220
SHIFT CONTROL SYSTEM ....................................222
Control Device Removal and Installation ..............222
Control Rod Removal and Installation ..................226
Adjustment of A/T Position ...................................227
Checking of A/T Position ......................................228
A/T SHIFT LOCK SYSTEM .....................................229
Description ............................................................229
Shift Lock System Electrical Parts Location .........229
Wiring Diagram — AT — SHIFT ...........................230
Diagnostic Procedure ...........................................232
ON-VEHICLE SERVICE ..........................................236
C o n t r o l V a l v e W i t h T C M a n d A / T F l u i d Te m p e r a t u r e
Sensor 2 ...............................................................236
Parking Components (2WD Models Only) ............248
Rear Oil Seal (VQ35DE Models Only) ..................260
Revolution Sensor Components (2WD Models
Only) .....................................................................261
AIR BREATHER HOSE ...........................................269
Removal and Installation ......................................269
TRANSMISSION ASSEMBLY ................................271
Removal and Installation (2WD Models) ..............271
Removal and Installation (AWD Models) ..............275
OVERHAUL .............................................................278
Components .........................................................278Oil Channel ...........................................................292
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................295
DISASSEMBLY .......................................................298
Disassembly ..........................................................298
REPAIR FOR COMPONENT PARTS ......................318
Oil Pump ...............................................................318
Front Sun Gear, 3rd One-Way Clutch ...................321
Front Carrier, Input Clutch, Rear Internal Gear .....323
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ..............................................329
High and Low Reverse Clutch ..............................335
Direct Clutch .........................................................337
ASSEMBLY .............................................................340
Assembly (1) .........................................................340
Adjustment ............................................................356
Assembly (2) .........................................................358
SERVICE DATA AND SPECIFICATIONS (SDS) ....365
General Specifications ......................................... .365
Vehicle Speed at Which Gear Shifting Occurs ......365
Vehicle Speed at Which Lock-Up Occurs/Releases .366
Stall Speed ............................................................366
Line Pressure ........................................................366
A/T Fluid Temperature Sensor ..............................366
Turbine Revolution Sensor ....................................367
Vehicle Speed Sensor A/T (Revolution Sensor) ...367
Reverse Brake ......................................................367
Total End Play .......................................................367

AT-10
PREPARATION
Revision: 2006 January2006 M35/M45
PREPARATIONPFP:00002
Special Service ToolsNCS001JG
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool nameDescription
ST2505S001
(J-34301-C)
Oil pressure gauge set
1. ST25051001
(—)
Oil pressure gauge
2. ST25052000
(—)
Hose
3. ST25053000
(—)
Joint pipe
4. ST25054000
(—)
Adapter
5. ST25055000
(—)
AdapterMeasuring line pressure
KV31103600
(J-45674)
Joint pipe adapter
(With ST25054000)Measuring line pressure
ST33400001
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
Installing rear oil seal (VQ35DE models for 2WD)
Installing oil pump housing oil seal
KV31102400
(J-34285 and J-34285-87)
Clutch spring compressor
a: 320 mm (12.60 in)
b: 174 mm (6.85 in)Installing reverse brake return spring retainer
ST25850000
(J-25721-A)
Sliding hammer
a: 179 mm (7.05 in)
b: 70 mm (2.76 in)
c: 40 mm (1.57 in)
d: M12X1.75PRemove oil pump assembly
SCIA3695J
ZZA1227D
NT086
NT423
NT422