wiring INFINITI M35 2007 Factory Service Manual

ACC-2
PRECAUTIONS
Revision: 2007 April2007 M35/M45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NBS005RO
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

ACS-1
AUTO CRUISE CONTROL SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION ACS
A
B
ACS
Revision: 2007 April2007 M35/M45
AUTO CRUISE CONTROL SYSTEM
ASCD
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ..... 3
Description ............................................................... 3
ICC
PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions for ICC System Service ........................ 4
PREPARATION ........................................................... 5
Special Service Tools ............................................... 5
DESCRIPTION ............................................................ 6
Outline ...................................................................... 6
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE ................................................................... 6
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ................................................. 6
BRAKE ASSIST (WITH PREVIEW FUNCTION) ..... 6
Functional Diagram .................................................. 7
Components Description .......................................... 9
CAN Communication ................................................ 9
CAN COMMUNICATION UNIT ............................. 9
Switch Operation .................................................... 10
IN VEHICLE-TO-VEHICLE DISTANCE CON-
TROL MODE ....................................................... 10
IN CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ............................................... 10
ICC System Display ................................................ 11
IN VEHICLE-TO-VEHICLE DISTANCE CON-
TROL MODE ........................................................ 11
IN CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ................................................ 11
ACTION TEST .......................................................... 12
ICC System Running Test ...................................... 12
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE ................................................................. 12
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ............................................... 13LASER BEAM AIMING ADJUSTMENT ................... 15
Outline .................................................................... 15
Preparation ............................................................. 15
Outline of Adjustment Procedure ............................ 15
Setting the ICC Target Board .................................. 15
ADJUSTING HEIGHT OF THE TARGET ............ 15
ADJUSTING THE RIGHT-LEFT POSITION OF
THE TARGET ...................................................... 16
SETTING THE TARGET ..................................... 16
Aiming Adjustment .................................................. 18
CHECK AFTER THE ADJUSTMENT .................. 20
ELECTRICAL UNITS LOCATION ............................ 21
Component Parts and Harness Connector Location ... 21
WIRING DIAGRAM ................................................... 22
Schematic ............................................................... 22
Wiring Diagram — ICC — ...................................... 23
TERMINALS AND REFERENCE VALUE ................. 28
Terminals and Reference Value for ICC Sensor Inte-
grated Unit .............................................................. 28
TROUBLE DIAGNOSIS - GENERAL DESCRIP-
TION .......................................................................... 29
Fail-Safe Function .................................................. 29
Work Flow ............................................................... 29
CONSULT-II Function (ICC) ................................... 30
DESCRIPTION .................................................... 30
CONSULT-II BASIC OPERATION ....................... 30
WORK SUPPORT ............................................... 30
SELF-DIAGNOSTIC RESULTS ........................... 31
DATA MONITOR ................................................. 31
ACTIVE TEST ..................................................... 33
Self-Diagnostic Function ......................................... 34
WITH CONSULT-II .............................................. 34
WITHOUT CONSULT-II ....................................... 35
SELF-DIAGNOSIS BY DOT MATRIX LCD WILL
NOT RUN ............................................................ 36
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 40
Diagnostic Trouble Code (DTC) Chart ................... 40
DTC 0 CONTROL UNIT ......................................... 42
DTC 1 POWER SUPPLY CIR, DTC 2 POWER SUP-

ACS-4
[ICC]
PRECAUTIONS
Revision: 2007 April2007 M35/M45
[ICC]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS004CC
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for ICC System ServiceNKS004CD

Do not look straight into the laser beam discharger when adjusting laser beam aiming.

Turn the MAIN switch OFF in conditions similar to driving, such as free rollers or a chassis dynamometer.

Do not use the ICC sensor integrated unit removing from vehicle. Never disassemble and remodel.

Erase DTC when replacing parts of ICC system, then check the operation of ICC system after adjusting
laser beam aiming if necessary.

DESCRIPTION
ACS-9
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
Components DescriptionNKS004CH
CAN CommunicationNKS004CI
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tric control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN COMMUNICATION UNIT
Refer to LAN-52, "CAN Communication Signal Chart" .
ComponentVehicle-to-
vehicle
distance
control modeConventional
(fixed speed)
cruise
control modeBrake assist
(with pre-
view func-
tion)Description
ICC sensor integrated unit×××

Controls vehicle distance by operating electric throttle
control actuator based on that sensor signals and
CAN communication data.

Controls vehicle distance by transmitting deceleration
degree commandment value signal to ABS actuator
and electric unit (control unit) when deceleration with
brake is needed.

Irradiates laser beam, and receives reflected laser
beam to measure distance from preceding vehicle.
ECM×××Transmits accelerator pedal position signal, ICC brake
switch signal, stop lamp switch signal and ICC steering
switch signal to ICC sensor integrated unit through CAN
communication.
ABS actuator and electric
unit (control unit)×××

Transmits vehicle speed signal (wheel speed) and
stop lamp switch signal to ICC sensor integrated unit
through CAN communication.

Receives deceleration degree commandment value
signal from ICC sensor integrated unit, and controls
brake fluid pressure with the ABS motor.
BCM×Transmits front wiper request signal to ICC sensor inte-
grated unit through CAN communication.
TCM××Transmits gear position signal and output shaft revolu-
tion signal to ICC sensor integrated unit through CAN
communication.
Unified meter and A/C amp.×××Receives meter display signal, ICC warning lamp signal
and buzzer output signal from ICC sensor integrated
unit through CAN communication.
ICC brake switch×××Transmits operating signal to ECM when depressing
brake pedal. ICC sensor integrated unit cancels cruise
system at driver's brake operation.
Stop lamp switch×××Transmits operating signal to ECM and ABS actuator
and electric unit (control unit) when depressing brake
pedal. ICC sensor integrated unit cancels cruise system
at driver's brake operation.

ACS-22
[ICC]
WIRING DIAGRAM
Revision: 2007 April2007 M35/M45
WIRING DIAGRAMPFP:00000
SchematicNKS004CS
TKWT3224E

WIRING DIAGRAM
ACS-23
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
Wiring Diagram — ICC —NKS004CT
TKWT5302E

ACS-24
[ICC]
WIRING DIAGRAM
Revision: 2007 April2007 M35/M45
TKWT3226E

WIRING DIAGRAM
ACS-25
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
TKWT5303E

ACS-26
[ICC]
WIRING DIAGRAM
Revision: 2007 April2007 M35/M45
TKWT5304E

WIRING DIAGRAM
ACS-27
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2007 April2007 M35/M45
TKWT5099E