lock INFINITI QX4 2001 Factory Service Manual

SMT844DB
Replacing Oil SealNBTF0068FRONT CASE OIL SEALNBTF0068S011. Drain transfer fluid.
2. Remove exhaust front tube and heat insulator. Refer to
ªRemovalº, TF-119.
3. Remove front propeller shaft. Refer to PD-6, ªRemoval and
Installationº.
4. Remove companion flange lock nut.
IDo not reuse lock nut.
SMT112D
5. Put a matchmark on top of drive pinion thread. The mark
should be in line with the mark on the companion flange.
IAlways mark top of drive pinion screw using paint.
SMT802C
6. Remove companion flange.
SMT803C
7. Remove front case oil seal.
8. Install front case oil seal.
IBefore installing, apply multi-purpose grease to seal lip.
9. Install companion flange.
SMT845DB
10. Tighten nut to the specified torque.
Refer to TF-121.
11. Install front propeller shaft.
ON-VEHICLE SERVICE
Replacing Oil Seal
TF-116

Transfer ComponentsNBTF0076
SMT810D
1. Oil seal
2. Transfer cover
3. Snap ring
4. Washer
5. Snap ring
6. Main gear bearing
7. Front case
8. Check plug
9. Check spring
10. Check ball
11. Internal gear
12. Snap ring
13. Bearing race
14. Thrust needle bearing
15. Planetary carrier
16. Thrust needle bearing
17. Sun gear18. L-H sleeve
19. 2-4 sleeve
20. Radial needle bearing
21. Front revolution sensor
22. Roll pin
23. L-H fork
24. 2-4 fork
25. Shift fork spring
26. Fork guide
27. Roll pin
28. Shift rod
29. Self-lock nut
30. Companion flange
31. Oil seal
32. Drain plug
33. Wait detection switch
34. Needle bearing35. Mainshaft
36. Drive chain
37. Clutch drum
38. Clutch hub
39. Snap ring
40. Driven plate
41. Drive plate
42. Retaining plate
43. Return spring assembly
44. Press flange
45. Washer
46. Thrust needle bearing
47. Snap ring
48. Seal ring
49. Front bearing
50. Front drive shaft
51. Rear bearing
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
OVERHAUL
Transfer Components
TF-121

SMT877C
Rear Case
DISASSEMBLYNBTF00771. Remove neutral-4LO switch and ATP switch.
2. Remove bolts.
SMT878C
3. Remove rear case from center case by tapping it lightly with a
plastic hammer.
SMT883C
Center Case
DISASSEMBLYNBTF00781. Remove oil pump shaft from main oil pump.
SMT884C
2. Remove stem bleeder from bleeder hole.
SMT844DB
3. Remove lock nut from companion flange.
IDo not reuse lock nut.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DISASSEMBLY
Rear Case
TF-123

SMT011D
Front Case
ASSEMBLYNBTF0082Planetary Carrier, Sun Gear and Internal GearNBTF0082S011. Apply ATF to oil seal periphery, and install oil seal so that it is
flush with the end face of front case.
IDo not reuse oil seal.
SMT012D
2. Install internal gear with its groove facing snap ring into front
case. Then secure it with snap ring.
IDo not reuse snap ring.
SMT108D
3. Remove all the liquid gasket on plug bolt and front case. Apply
locking sealant to plug bolt, install it to front case and tighten
it to specified torque.
IWith one crest of plug bolt inserted in the hole, apply liquid
gasket 1215 to the thread.
: 19 - 25 N´m (1.9 - 2.5 kg-m, 14 - 18 ft-lb)
SMT014D
4. Install snap ring to main gear bearing.
IDo not reuse snap rings.
SMT015D
5. Set main gear bearing to front case, then press it.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Front Case
TF-141

SMT021D
15. Install washer to sun gear assembly, and select proper snap
ring so that end play ªFº of sun gear is within specifications.
Standard end play ªFº:
0 - 0.15 mm (0 - 0.0059 in)
Snap ring: Refer to SDS, TF-159.
SMT022D
16. Install the selected snap ring.
IDo not reuse snap rings.
17. Apply ATF to the periphery of new transfer cover oil seal, and
attach it at 1.5 mm (0.059 in) from the transfer cover and face.
IDo not reuse oil seal.
SMT023D
18. Apply sealing fluid (Locktite 518´C1335 x 25) to transfer cover
mounting surface of front case as shown in the figure.
CAUTION:
IRemove all foreign materials such as water, oil, and
grease from mating surfaces of front case and transfer
cover.
IPrevent sealing fluid from entering into oil holes of front
case.
SMT024D
19. Align oil hole of front case with notch of transfer cover, and
tighten bolts.
: 49 - 58 N´m (5.0 - 5.9 kg-m, 36 - 43 ft-lb)
IDo not reuse bolts.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Front Case (Cont'd)
TF-143

SMT989C
5. Align claw of oil gutter with center case, and install it.
6. Install front case assembly and rear case assembly.
Refer to ªFinal Assemblyº, TF-153.
SMT891C
Final AssemblyNBTF00841. Install C-rings to mainshaft rear bearing.
SMT889C
2. Check speedometer drive gear teeth for abnormal wear. Set
speedometer drive gear properly on mainshaft, and secure it
with snap ring.
IDo not reuse snap ring.
SMT893C
3. Apply sealing fluid 518 (Locktite) to the entire center case
mounting surface of front case as shown in the figure.
CAUTION:
Remove all foreign materials such as water, oil and grease
from center case and front case mating surfaces.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Center Case (Cont'd)
TF-153

SMT881C
11. Remove rear oil seal.
IDo not reuse oil seal.
SMT882C
12. Apply ATF to the circumference of new rear oil seal, and tap it
using a drift as shown in the figure so that it is aligned with
case tip face.
IApply multi-purpose grease to oil seal lip.
SMT879C
13. Apply sealing fluid 518 (Locktite) to entire rear case mounting
surface of center case as shown in the figure.
CAUTION:
IRemove all foreign materials such as water, oil, and
grease from center case and rear case mating surfaces.
IBe careful not to allow sealing fluid to clog bleeder hole.
14. Install rear case to center case, and tighten bolts to specified
torque.
: 41 - 48 N´m (4.2 - 4.9 kg-m, 30 - 35 ft-lb)
IBe sure to attach harness clips.
SMT880C
15. Remove all the gasket fluid 1215 (Three Bond) from switch
mounting area and inside rear case, with ATP switch and neu-
tral-4LO switch threaded in 1 to 2 pitches, apply gasket fluid
1215 (Three Bond) to the thread of the switches and tighten it
to specified torque.
: 15 - 20 N´m (1.5 - 2.0 kg-m, 11 - 14 ft-lb)
16. Install rear case assembly to center case assembly.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Final Assembly (Cont'd)
TF-155

General SpecificationsNBTF0085
Transfer modelATX14A
Gear ratioHigh1.000
Low2.596
Number of teethPlanetary gearSun gear 57
Internal gear 91
Front drive sprocket 35
Front drive shaft 35
Fluid capacity(US qt, Imp qt)*3.0 (3-1/8, 2-5/8)
*: Refer to MA-11, ªFluids and Lubricantsº.
Inner Gear and Outer GearNBTF0086SUB-OIL PUMPNBTF0086S01
Allowable clearance 0.015 - 0.035 mm (0.0006 - 0.0014 in)
Gear thickness mm (in)Part No.*
Inner gear Outer gear
9.27 - 9.28 (0.3650 - 0.3654) 31346 0W462 31347 0W462
9.28 - 9.29 (0.3654 - 0.3657) 31346 0W461 31347 0W461
9.29 - 9.30 (0.3657 - 0.3661) 31346 0W460 31347 0W460
*: Always check with the Parts Department for the latest parts information.
MAIN OIL PUMPNBTF0086S02
Allowable clearance 0.015 - 0.035 mm (0.0006 - 0.0014 in)
Gear thickness mm (in)Part No.*
Inner gear Outer gear
14.67 - 14.68 (0.5776 - 0.5780) 31346 0W412 31347 0W412
14.68 - 14.69 (0.5780 - 0.5783) 31346 0W411 31347 0W411
14.69 - 14.70 (0.5783 - 0.5787) 31346 0W410 31347 0W410
*: Always check with the Parts Department for the latest parts information.
Control ValveNBTF0087VALVENBTF0087S01
Mounting position Part name Part No.* Outer dia. mm (in) Overall length mm (in)
L1 2-4 shift valve 31772 21X00 8.0 (0.315) 38.5 (1.516)
L2 Clutch valve 31772 80X11 10.0 (0.394) 40.0 (1.575)
L4 Pilot valve 31772 80X11 10.0 (0.394) 40.0 (1.575)
L5 Regulator valve 31741 0W410 12.0 (0.472) 68.0 (2.677)
*: Always check with the Parts Department for the latest parts information.
SPRINGNBTF0087S02
Mounting position Part name Part No.*Free length
mm (in)Outer dia.
mm (in)Wire dia. mm (in) Winding direction
L12-4 shift valve
spring31742 0W400 31.85 (1.2539) 7.0 (0.276) 0.6 (0.024) Clockwise
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
TF-157

Mounting position Part name Part No.*Free length
mm (in)Outer dia.
mm (in)Wire dia. mm (in) Winding direction
L2 Clutch valve spring 31742 0W405 40.6 (1.598) 9.0 (0.354) 0.8 (0.031) Clockwise
L4 Pilot valve spring 31742 0W410 28.1 (1.106) 9.0 (0.354) 1.2 (0.047) Clockwise
L5Regulator valve
spring31742 0W415 39.7 (1.563) 11.0 (0.433) 1.3 (0.051) Clockwise
*: Always check with the Parts Department for the latest parts information.
ClutchNBTF0088DRIVE PLATENBTF0088S01
Part No.* Quantity Initial thickness mm (in) Limit value mm (in)
31532 0W410 8 2.0 (0.079) 1.8 (0.071)
*: Always check with the Parts Department for the latest parts information.
DRIVEN PLATENBTF0088S04
Part No.* Quantity Initial thickness mm (in) Limit value mm (in)
31536 0W410 14 2.0 (0.079) 0 (0) (steel plate)
*: Always check with the Parts Department for the latest parts information.
RETURN SPRINGNBTF0088S02
Stamped mark Part No.* Free length mm (in) Outer dia. mm (in) Wire dia. mm (in) Winding direction
1 31521 0W401 37.3 (1.496)
12.0 (0.472) 1.8 (0.071) Clockwise 2 31521 0W402 37.8 (1.488)
3 31521 0W403 38.4 (1.512)
4 31521 0W404 38.9 (1.531)
5 31521 0W405 39.4 (1.551)
6 31521 0W406 40.0 (1.575)
7 31521 0W407 36.8 (1.449)
8 31521 0W408 40.5 (1.594)
*: Always check with the Parts Department for the latest parts information.
RETAINING PLATENBTF0088S03
Standard end play 0.2 - 0.5 mm (0.008 - 0.020 in)
Measured value mm (in) Part No.* Thickness mm (in)
2.30 - 2.50 (0.0906 - 0.0984) 31537 0W410 2.1 (0.083)
2.50 - 2.70 (0.0984 - 0.1063) 31537 0W411 2.3 (0.091)
2.70 - 2.90 (0.1063 - 0.1142) 31537 0W412 2.5 (0.098)
2.90 - 3.10 (0.1142 - 0.1220) 31537 0W413 2.7 (0.106)
3.10 - 3.30 (0.1220 - 0.1299) 31537 0W414 2.9 (0.114)
3.30 - 3.50 (0.1299 - 0.1378) 31537 0W415 3.1 (0.122)
3.50 - 3.70 (0.1378 - 0.1457) 31537 0W416 3.3 (0.130)
3.70 - 3.90 (0.1457 - 0.1535) 31537 0W417 3.5 (0.138)
3.90 - 4.10 (0.1535 - 0.1614) 31537 0W418 3.7 (0.146)
4.10 - 4.30 (0.1614 - 0.1693) 31537 0W419 3.9 (0.154)
SERVICE DATA AND SPECIFICATIONS (SDS)
Control Valve (Cont'd)
TF-158