turn signal INFINITI QX4 2005 Factory Owners Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: QX4, Model: INFINITI QX4 2005Pages: 3419, PDF Size: 80.18 MB
Page 710 of 3419
NAVIGATION SYSTEM
AV-121
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
Vehicle Speed Signal Check for NAVI Control UnitEKS00BJZ
1. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152, combination meter connector M24 and display control unit
connector M94.
3. Check continuity between NAVI control unit harness connector
B152 terminal 28 (W/R) and combination meter harness con-
nector M24 terminal 29 (W/R).
4. Check continuity between NAVI control unit harness connector
B152 terminal 28 (W/R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness.
2. CHECK 1: VEHICLE SPEED SIGNAL
1. Connect NAVI control unit connector.
2. Turn ignition switch ON.
3. Check voltage between NAVI control unit harness connector
B152 terminal 28 (W/R) and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace NAVI control unit. Refer to AV-157, "
Removal
and Installation of NAVI Control Unit" .
3. CHECK 2: VEHICLE SPEED SIGNAL
1. Connect combination meter connector and display control unit connector.
2. Drive vehicle at a constant speed.
3. Check signal between NAVI control unit harness connector
B152 terminal 28 (W/R) and ground with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-157, "Removal
and Installation of NAVI Control Unit" .
NG >> Check combination meter system. Refer to DI-19, "
Veh i-
cle Speed Signal Inspection" . Continuity should exist.
Continuity should not exist.
WKIA1769E
Approx. 3.5V or more
SKIA4295E
28 (W/R) – Ground : Refer to AV-90, "Terminals
and Reference Value for NAVI
Control unit" .
SKIA4615E
Page 711 of 3419
AV-122
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Vehicle Speed Signal Check for Display Control UnitEKS00BK0
1. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M94, combination meter connector M24 and NAVI control unit
connector B152.
3. Check continuity between display control unit harness connector
M94 terminal 16 (W/R) and combination meter harness connec-
tor M24 terminal 29 (W/R).
4. Check continuity between display control unit harness connector
M94 terminal 16 (W/R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness.
2. CHECK 1: VEHICLE SPEED SIGNAL
1. Connect display control unit connector.
2. Turn ignition switch ON.
3. Check voltage between display control unit harness connector
M94 terminal 16 (W/R) and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace display control unit. Refer to AV- 1 5 8 , "
Removal
and Installation of Display Control Unit" .
3. CHECK 2: VEHICLE SPEED SIGNAL
1. Connect combination meter connector and NAVI control unit connector.
2. Drive vehicle at a constant speed.
3. Check signal between display control unit harness connector
M94 terminal 16 (W/R) and ground with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> Replace display control unit. Refer to AV- 1 5 8 , "Removal
and Installation of Display Control Unit" .
NG >> Check combination meter system. Refer to DI-19, "
Vehi-
cle Speed Signal Inspection" . Continuity should exist.
Continuity should not exist.
WKIA1506E
Approx. 3.5V or more
SKIA4297E
16 (W/R) – Ground : Refer to AV- 9 2 , "Terminals
and Reference Value for Dis-
play Control unit" .
SKIA4616E
Page 712 of 3419
NAVIGATION SYSTEM
AV-123
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
Illumination Signal Check for NAVI Control UnitEKS00BK1
1. CHECK ILLUMINATION SIGNAL
1. Turn the ignition switch ON.
2. Check voltage between NAVI control unit and ground.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-157, "Removal
and Installation of NAVI Control Unit" .
NG >> Check harness for open or short between NAVI control unit and IPDM E/R.
Illumination Signal Check for Display Control Unit EKS00BK2
1. CHECK ILLUMINATION SIGNAL
1. Turn ignition switch ON.
2. Check voltage between display control unit and ground.
OK or NG
OK >> Replace display control unit. Refer to AV-158, "Removal
and Installation of Display Control Unit" .
NG >> Check harness for open or short between display control unit and IPDM E/R.
Ignition Signal Check for NAVI Control UnitEKS00BK3
1. CHECK IGNITION SIGNAL
1. Disconnect NAVI control unit connector B152.
2. Turn ignition switch ON.
3. Check voltage between NAVI control unit harness connector
B152 terminal 26 (G/R) and ground.
OK or NG
OK >> Replace NAVI control unit. Refer to AV-157, "Removal
and Installation of NAVI Control Unit" .
NG >> Check harness for open or short between NAVI control
unit and fuse.
Te r m i n a l s
Lighting switch position
(+)
(–)
ConnectorTe r m i n a l
(Wire color)1st or 2nd
positionOFF
B152 25 (R/L) GroundBattery
voltageApprox. 0V
SKIA4298E
Te r m i n a l s
Lighting switch position
(+)
(–)
ConnectorTe r m i n a l
(Wire color)1st or 2nd
positionOFF
M94 14 (R/L) GroundBattery
voltageApprox. 0V
SKIA4299E
Battery voltage should exist.
SKIA4300E
Page 713 of 3419
AV-124
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Ignition Signal Check for Display Control UnitEKS00BK4
1. CHECK IGNITION SIGNAL
1. Disconnect display control unit connector M94.
2. Turn ignition switch ON.
3. Check voltage between display control unit harness connector
M94 terminal 12 (G/R) and ground.
OK or NG
OK >> Replace display control unit. Refer to AV- 1 5 8 , "Removal
and Installation of Display Control Unit" .
NG >> Check harness for open or short between display con-
trol unit and fuse.
Reverse Signal Check for NAVI Control UnitEKS00BK5
1. CHECK REVERSE LAMP
1. Turn ignition switch ON.
2. Place selector lever into R-position. Do back-up lamps come on?
YES or NO
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT-106, "
BACK-UP LAMP" .
2. CHECK REVERSE SIGNAL
1. Disconnect NAVI control unit connector B152.
2. Turn ignition switch ON.
3. With the selector lever in R-position, check voltage between
NAVI control unit and ground.
OK or NG
OK >> Replace NAVI control unit. Refer to AV- 1 5 7 , "Removal
and Installation of NAVI Control Unit" .
NG >> Check harness for open or short between NAVI control unit and back-up lamp position relay.
Reverse Signal Check for Display Control UnitEKS00BK6
1. CHECK REVERSE LAMP
1. Turn ignition switch ON.
2. Place selector lever into R-position. Do back-up lamps come on?
YES or NO
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT-106, "
BACK-UP LAMP" . Battery voltage should exist.
WKIA1230E
Te r m i n a l s
Selector lever position
(+)
(–)
ConnectorTe r m i n a l
(Wire color)R-positionOther than R-
position
B152 27 (G/W) Ground Battery voltage Approx. 0V
SKIA4302E
Page 714 of 3419
NAVIGATION SYSTEM
AV-125
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
2. CHECK REVERSE SIGNAL
1. Disconnect display control unit connector M94.
2. Turn ignition switch ON.
3. With the selector lever in R-position, check voltage between dis-
play control unit and ground.
OK or NG
OK >> Replace display control unit. Refer to AV-158, "Removal
and Installation of Display Control Unit" .
NG >> Check harness for open or short between display control unit and back-up lamp position relay.
AV Communication Line Check (Between Display Control Unit and NAVI Control
Unit)
EKS00BK7
1. CHECK POWER SUPPLY AND GROUND CIRCUIT
1. Check power supply and ground circuit for NAVI control unit. Refer to AV- 11 6 , "
Power Supply and Ground
Circuit Check for NAVI Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B152 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
4. Check continuity between NAVI control unit and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
Te r m i n a l s
Selector lever position
(+)
(–)
ConnectorTe r m i n a l
(Wire color)R-positionOther than
R-position
M94 6 (GR) Ground Battery voltage Approx. 0V
SKIA4303E
Te r m i n a l s
Continuity NAVI control unit Display control unit
ConnectorTe r m i n a l
(Wire color)ConnectorTerminal
(Wire color)
B15244 (L)
M9532 (L)
Ye s
45 (P) 34 (P)
Te r m i n a l s
Continuity NAVI control unit
—
Connector Terminal (Wire color)
B15244 (L)
Ground No
45 (P)
SKIA4444E
Page 716 of 3419
NAVIGATION SYSTEM
AV-127
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
3. CHECK 1: AUDIO-TX COMMUNICATION SIGNAL
1. Connect display control unit connector.
2. Turn ignition switch ON.
3. Check voltage between display control unit harness connector
M95 terminal 42 (W/L) and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace display control unit. Refer to AV-158, "
Removal
and Installation of Display Control Unit" .
4. CHECK 2: AUDIO-RX COMMUNICATION SIGNAL
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95.
3. Connect audio unit connector M45.
4. Turn ignition switch ON.
5. Check voltage between audio unit harness connector M45 ter-
minal 65 (O/L) and ground.
OK or NG
OK >> GO TO 5.
NG >> Replace audio unit. Refer to AV- 4 5 , "
Removal and
Installation for Audio Unit" .
5. CHECK 3: AUDIO-TX COMMUNICATION SIGNAL
1. Turn ignition switch OFF.
2. Connect display control unit connector M95.
3. Turn ignition switch ON.
4. Check signal between display control unit harness connector
M95 terminal 40 (O/L) and ground with CONSULT-II or oscillo-
scope.
OK or NG
OK >> GO TO 6.
NG >> Replace display control unit. Refer to AV-158, "
Removal
and Installation of Display Control Unit" . Approx. 3.5V or more.
WKIA1770E
Approx. 3.5V or more.
WKIA1771E
40 (O/L) - Ground : Refer to AV- 9 2 , "Terminals
and Reference Value for Dis-
play Control unit" .
SKIA4447E
Page 717 of 3419
AV-128
NAVIGATION SYSTEM
Revision: October 20052005 QX56
6. CHECK 4: AUDIO-RX COMMUNICATION SIGNAL
1. Turn ignition switch ON.
2. Check signal between display control unit harness connector
M95 terminal 42 (W/L) and ground with CONSULT-II or oscillo-
scope.
OK or NG
OK >> Inspection End.
NG >> Replace audio unit. Refer to AV- 4 5 , "
Removal and
Installation for Audio Unit" .
Display Communication Line Check (Between Display Control Unit and Display
Unit)
EKS00BK9
1. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display unit connector M93 and display control unit connector M95.
3. Check continuity between display control unit and display unit.
4. Check continuity between display control unit and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK 1: COMMUNICATION SIGNAL (DCU–DSP)
1. Connect display unit connector.
2. Turn ignition switch ON.
3. Check voltage between display unit harness connector M93 ter-
minal 11 (B/W) and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace display unit. Refer to AV- 1 5 8 , "
Removal and
Installation of Display Unit" . 42 (W/L) - Ground : Refer to AV-92, "
Te r m i na l s
and Reference Value for Dis-
play Control unit" .
SKIA4448E
Te r m i n a l s
Continuity Display control unit Display unit
ConnectorTerminal
(Wire color)ConnectorTe r m i n a l
(Wire color)
M9536 (B/W)
M9311 (B/W)
Ye s
38 (L) 22 (L)
Te r m i n a l s
Continuity Display control unit
—
Connector Terminal (Wire color)
M9536 (B/W)
Ground No
38 (L)
WKIA2019E
Approx. 3.5V or more.
WKIA1377E
Page 718 of 3419
NAVIGATION SYSTEM
AV-129
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
3. CHECK 2: COMMUNICATION SIGNAL (DSP–DCU)
1. Turn ignition switch OFF.
2. Disconnect display control unit connector M95.
3. Connect display control unit connector.
4. Turn ignition switch ON.
5. Check voltage between display control unit harness connector
M95 terminal 38 (L) and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace display control unit. Refer to AV-158, "
Removal
and Installation of Display Control Unit" .
4. CHECK 3: COMMUNICATION SIGNAL (DCU–DSP)
1. Turn ignition switch OFF.
2. Connect display unit connector.
3. Turn ignition switch ON.
4. Check signal between display control unit harness connector
M95 terminal 36 (B/W) and ground with CONSULT-II or oscillo-
scope.
OK or NG
OK >> GO TO 5.
NG >> Replace display control unit. Refer to AV-158, "
Removal
and Installation of Display Control Unit" .
5. CHECK 4: COMMUNICATION SIGNAL (DSP–DCU)
1. Turn ignition switch ON.
2. Check signal between display control unit harness connector
M95 terminal 38 (L) and ground with CONSULT-II or oscillo-
scope.
OK or NG
OK >> Inspection End.
NG >> Replace display unit. Refer to AV-158, "
Removal and
Installation of Display Unit" . Approx. 3.5V or more.
SKIA4453E
36 (B/W) – Ground : Refer to AV- 9 2 , "Terminals
and Reference Value for Dis-
play Control unit" .
SKIA4452E
38 (L) – Ground : Refer to AV- 9 2 , "Terminals
and Reference Value for Dis-
play Control unit" .
SKIA4453E
Page 722 of 3419
NAVIGATION SYSTEM
AV-133
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
2. CHECK HORIZONTAL SYNCHRONIZATION SIGNAL
1. Connect display control unit connector and display unit connector.
2. Turn ignition switch ON.
3. Check signal between display control unit connector M95 termi-
nals 55 (R) and 49 with CONSULT-II or oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> Replace display unit. Refer to AV-158, "
Removal and
Installation of Display Unit" .
3. CHECK VERTICAL SYNCHRONIZATION SIGNAL
1. Turn ignition switch ON.
2. Check signal between display control unit connector M95 termi-
nals 53 (W) and 49 with CONSULT-II or oscilloscope.
OK or NG
OK >> GO TO 4.
NG >> Replace display unit. Refer to AV-158, "
Removal and
Installation of Display Unit" .
4. CHECK RGB AREA SIGNAL
1. Press the “TRIP” button.
2. Check signal between display control unit connector M95 termi-
nals 51 (B) and 49 with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace display unit. Refer to AV-158, "Removal and
Installation of Display Unit" .
NG >> Replace display control unit. Refer to AV-158, "
Removal
and Installation of Display Control Unit" . 55 (R) - 49 : Refer to AV- 9 2 , "
Terminals and Refer-
ence Value for Display Control unit" .
SKIA4305E
53 (W) - 49 : Refer to AV- 9 2 , "Terminals and Refer-
ence Value for Display Control unit" .
WKIA1773E
51 (B) – 49 : Refer to AV- 9 2 , "Terminals and Refer-
ence Value for Display Control unit" .
SKIA4306E
Page 723 of 3419
AV-134
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Color of RGB Image is Not Proper (Only NAVI Screen Looks Bluish)EKS00BKG
1. CHECK RGB HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector B151 and display control unit connector M95.
3. Check continuity between NAVI control unit and display control unit.
4. Check continuity between NAVI control unit and ground.
When the screen looks bluish.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK RGB SIGNAL
1. Connect NAVI control unit connector and display control unit connector.
2. Turn ignition switch ON.
3. Display “Color bar” by “CONFIRMATION/ADJUSTMENT” mode.
4. Check signal between NAVI control unit connector B151 termi-
nal 18 (R) and 17 with CONSULT-II or oscilloscope.
When the screen looks bluish.
Voltage signal between NAVI control unit connector B151 termi-
nal 18 (R) and 17.
OK or NG
OK >> Replace display control unit. Refer to AV- 1 5 8 , "Removal
and Installation of Display Control Unit" .
NG >> Replace NAVI control unit. Refer to AV- 1 5 7 , "
Removal and Installation of NAVI Control Unit" .
Te r m i n a l s
Continuity NAVI control unit Display control unit
ConnectorTerminal
(Wire color)ConnectorTe r m i n a l
(Wire color)
B15118 (R)
M9544 (R/L)
Ye s
17 45
Te r m i n a l s
Continuity NAVI control unit
—
Connector Terminal (Wire color)
B15118 (R)
Ground No
17
SKIA4349E
18 (R) – 17 : Refer to AV- 9 0 , "Te r m i n a l s
and Reference Value for
NAVI Control unit" .
SKIA4629E