speed sensor INFINITI QX56 2004 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2004, Model line: QX56, Model: INFINITI QX56 2004Pages: 3371, PDF Size: 78.5 MB
Page 1122 of 3371
COMBINATION METERS
DI-19
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Symptom ChartEKS007DV
Vehicle Speed Signal InspectionEKS007DW
1. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
Refer to BRC-29, "
SELF-DIAGNOSIS" .
OK or NG
OK >> Replace the combination meter. Refer to IP-13, "Combination Meter" .
NG >> Perform the "Diagnostic Procedure" for displayed DTC. Refer to BRC-11, "
TROUBLE DIAGNO-
SIS" .
Engine Oil Pressure Signal Inspection EKS0086D
1. CHECK OIL PRESSURE SENSOR SIGNAL
1. Turn ignition switch ON.
2. Check voltage between combination meter harness connector
M24 terminal 20 (Y) and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
Trouble phenomenon Possible cause
Improper tachometer indication. Refer to DI-21, "
Engine Speed Signal Inspection" .
Improper water temperature gauge indication. Refer to DI-21, "
Water Temperature Signal Inspection" .
Improper speedometer or odometer. Refer to DI-19, "
Vehicle Speed Signal Inspection" .
Improper fuel gauge indication.
Refer to DI-22, "
Fuel Level Sensor Unit Inspection" .
Fuel warning lamp indication is irregular.
Improper A/T oil temperature gauge indicationRefer to AT-131, "
DTC P1710 A/T FLUID TEMPERATURE SEN-
SOR CIRCUIT" .
Improper voltage gauge indication
Replace combination meter. Refer to IP-13, "
Combination Meter"
.
More than one gauge does not give proper indication.
Improper A/T position indication. Refer to DI-41, "
A/T INDICATOR" .
Illumination control does not operate properly. Refer to LT-152, "
ILLUMINATION" .
Te r m i n a l s
Condition Voltage (V) (+)
(–)
ConnectorTe r m i n a l
(Wire color)
M24 20 (Y) GroundWhen ignition switch is in ON
position. (Engine stopped)Ye s
Engine running. (Idle speed) Yes
WKIA1833E
Page 1124 of 3371
COMBINATION METERS
DI-21
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
5. CHECK OIL PRESSURE SENSOR SIGNAL CIRCUIT
1. Check continuity between combination meter harness connector M24 terminal 20 (Y) and oil pressure
sensor harness connector F4 terminal 2 (Y).
2. Check continuity between combination meter harness connector
M24 terminal 20 (Y) and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness or connector.
6. CHECK OIL PRESSURE SENSOR GROUND CIRCUIT
Check continuity between combination meter harness connector
M24 terminal 16 (B/P) and ground.
OK or NG
OK >> Replace oil pressure sensor.
NG >> Repair harness or connector.
Water Temperature Signal Inspection EKS007DX
1. CHECK ECM SELF-DIAGNOSIS
Perform ECM self-diagnosis. Refer to EC-107, "
SELF-DIAG RESULTS MODE" .
OK or NG
OK >> Replace the combination meter. Refer to IP-13, "Combination Meter" .
NG >> Perform "Diagnostic procedure" for displayed DTC. Refer to EC-71, "
TROUBLE DIAGNOSIS" .
Engine Speed Signal Inspection EKS007DY
1. CHECK ECM SELF-DIAGNOSIS
Perform ECM self-diagnosis. Refer to EC-107, "
SELF-DIAG RESULTS MODE" .
OK or NG
OK >> Replace the combination meter. Refer to IP-13, "Combination Meter" .
NG >> Perform "Diagnostic procedure" for displayed DTC. Refer to EC-71, "
TROUBLE DIAGNOSIS" . Continuity should exist.
Continuity should not exist.
WKIA1836E
Continuity should not exist.
WKIA2685E
Page 1129 of 3371
DI-26
COMPASS AND THERMOMETER
Revision: August 20072004 QX56
COMPASS AND THERMOMETERPFP:24835
System DescriptionEKS007E4
This unit displays the following items:
Earth magnetism and heading direction of vehicle.
Outside air temperature.
Caution for frozen road surfaces.
OUTSIDE TEMPERATURE DISPLAY
Push the mode switch when the ignition switch is in the ON position. The outside temperature will be displayed
in “°F”.
Selecting the indication range
Push the mode switch to change from °F → °C → OFF → °F.
The indicated temperature on the thermometer is not readily affected by engine heat. It changes only
when one of the following conditions is present.
–The temperature detected by the ambient sensor is lower than the indicated temperature on the thermom-
eter.
–The vehicle speed is greater than 20 km/h (13 MPH).
(This is to prevent the indicated temperature from being affected by engine heat during low-speed driv-
ing.)
–The ignition switch has been turned to the OFF position for more than 2 hours. (The engine is cold.)
DIRECTION DISPLAY
Push the mode switch when the ignition switch is in the ON position. The direction will be displayed.
WKIA1817E
Page 1131 of 3371
DI-28
COMPASS AND THERMOMETER
Revision: August 20072004 QX56
Trouble DiagnosesEKS007E6
PRELIMINARY CHECK FOR THERMOMETER
1. COOL DOWN CHECK
1. Turn the ignition switch to the ON position.
2. Cool down the ambient sensor with water or ice.
Does the indicated temperature drop?
Yes >> GO TO 2.
No >> The system is malfunctioning. Refer to DI-28, "
INSPECTION/COMPASS AND THERMOMETER"
.
2. WARM UP CHECK
1. Leave the vehicle for 10 minutes.
2. With the ignition switch in the ON position, disconnect and reconnect the ambient sensor connector.
Does the indicated temperature rise?
Yes >> The system is OK.
No >> The system is malfunctioning. Refer to DI-28, "
INSPECTION/COMPASS AND THERMOMETER"
.
NOTE:
The indicated temperature on the thermometer is not readily affected by engine heat. It changes only
when one of the following conditions is present.
–The temperature detected by the ambient sensor is lower than the indicated temperature on the thermom-
eter.
–The vehicle speed is greater than 20 km/h (13 MPH).
(This is to prevent the indicated temperature from being affected by engine heat during low-speed driv-
ing.)
–The ignition switch has been turned to the OFF position for more than 2 hours. (The engine is cold.)
INSPECTION/COMPASS AND THERMOMETER
Symptom Possible causes Repair order
No display at all 1. 10A fuse
2. Ground circuit
3. Compass and thermometer1. Check 10A fuse [No. 12, located in fuse block (J/B)].
Turn the ignition switch ON and verify that battery positive volt-
age is at terminal 2 of compass and thermometer.
2. Check ground circuit for compass and thermometer.
3. Replace compass and thermometer.
Forward direction indi-
cation slips off the mark
or incorrect.1. In manual correction mode (Bar and
display vanish.)
2. Zone variation change is not done.1. Drive the vehicle and turn at an angle of 90°.
2. Perform the zone variation change.
Compass reading
remains unchanged.1. Vehicle speed signal is not entered.
2. Compass and thermometer1. Check harness for open or short between combination meter
terminal 29 and compass and thermometer terminal 8.
2. Replace compass and thermometer.
Displays wrong tem-
perature when ambient
temperature is between
−40°C (−40°F) and
55°C (130°F). (See
NOTE above.)1. Check operation
2. Ambient sensor circuit
3. Vehicle speed signal is not entered.
4. Ambient sensor
5. Compass and thermometer1. Perform preliminary check shown above.
2. Check harness for open or short between ambient sensor and
compass and thermometer.
3. Check harness for open or short between combination meter
terminal 29 and compass and thermometer terminal 8.
4. Replace ambient sensor.
5. Replace compass and thermometer.
Displays SC or OC. 1. Ambient sensor circuit.
2. Ambient sensor.
3. Compass and thermometer.1. Check harness for open or short between ambient sensor and
compass and thermometer.
2. Replace ambient sensor.
3. Replace compass and thermometer.
Page 1141 of 3371
DI-38
WARNING LAMPS
Revision: August 20072004 QX56
Oil Pressure Warning Lamp Stays Off (Ignition Switch ON)EKS007EA
1. CHECK OIL PRESSURE SENSOR SIGNAL
1. Turn ignition switch ON.
2. Check voltage between combination meter harness connector
M24 terminal 20 (Y) and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK OIL PRESSURE SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector M24 and oil pressure
sensor connector F4.
3. Check continuity between combination meter harness connector
M24 terminal 16 (B/P) and oil pressure sensor harness connec-
tor F4 terminal 3 (B/P).
OK or NG
OK >> Replace the combination meter. Refer to IP-13, "Combi-
nation Meter" .
NG >> Repair harness or connector.
3. CHECK OIL PRESSURE SENSOR REFERENCE VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect oil pressure sensor connector F4.
3. Turn ignition switch ON.
4. Check voltage between combination meter harness connector
M24 terminal 22 (GR/L) and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace the combination meter. Refer to IP-13, "
Combi-
nation Meter" .
Terminals
Condition Voltage (V) (+)
(–)
ConnectorTe r m i n a l
(Wire color)
M24 20 (Y) GroundWhen ignition switch is in ON
position. (Engine stopped)Ye s
Engine running. (Idle speed) Yes
WKIA1833E
Continuity should exist.
WKIA1837E
Voltage : Approx. 5V
WKIA1834E
Page 1192 of 3371
EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
Revision: August 20072004 QX56 INDEX FOR DTC ........................................................ 8
Alphabetical Index .................................................... 8
DTC No. Index ....................................................... 12
PRECAUTIONS ........................................................ 16
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 16
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 16
Precaution .............................................................. 16
Wiring Diagrams and Trouble Diagnosis ................ 19
PREPARATION ......................................................... 20
Special Service Tools ............................................. 20
Commercial Service Tools ...................................... 22
ENGINE CONTROL SYSTEM .................................. 23
System Diagram ..................................................... 23
Vacuum Hose Drawing ........................................... 24
System Chart ......................................................... 25
Multiport Fuel Injection (MFI) System .................... 26
Electronic Ignition (EI) System ............................... 28
Nissan Torque Demand (NTD) Control System ..... 29
Air Conditioning Cut Control ................................... 30
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 30
CAN communication .............................................. 31
BASIC SERVICE PROCEDURE .............................. 32
Idle Speed and Ignition Timing Check .................... 32
Idle Speed/Ignition Timing/Idle Mixture Ratio
Adjustment ............................................................. 33
Accelerator Pedal Released Position Learning ...... 44
Throttle Valve Closed Position Learning ................ 44
Idle Air Volume Learning ........................................ 44
Fuel Pressure Check .............................................. 46
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 49
Introduction ............................................................ 49
Two Trip Detection Logic ........................................ 49
Emission-related Diagnostic Information ................ 50
IVIS (Infiniti Vehicle Immobilizer System — NATS) ... 63
Malfunction Indicator Lamp (MIL) ........................... 63
OBD System Operation Chart ................................ 66TROUBLE DIAGNOSIS ............................................ 71
Trouble Diagnosis Introduction ............................... 71
DTC Inspection Priority Chart ................................. 76
Fail-safe Chart ........................................................ 77
Basic Inspection ..................................................... 79
Symptom Matrix Chart ............................................ 84
Engine Control Component Parts Location ............ 88
Circuit Diagram ....................................................... 94
ECM Harness Connector Terminal Layout ............. 96
ECM Terminals and Reference Value ..................... 96
CONSULT-II Function ...........................................103
Generic Scan Tool (GST) Function .......................116
CONSULT-II Reference Value in Data Monitor .....118
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................121
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .123
Description ............................................................123
Testing Condition ..................................................123
Inspection Procedure ............................................123
Diagnostic Procedure ...........................................124
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................127
Description ............................................................127
Diagnostic Procedure ...........................................127
POWER SUPPLY AND GROUND CIRCUIT ...........128
Wiring Diagram .....................................................128
Diagnostic Procedure ...........................................129
Ground Inspection ................................................133
DTC U1000, U1001 CAN COMMUNICATION LINE .135
Description ............................................................135
On Board Diagnosis Logic ....................................135
DTC Confirmation Procedure ...............................135
Wiring Diagram .....................................................136
Diagnostic Procedure ...........................................137
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .138
Description ............................................................138
CONSULT-II Reference Value in Data Monitor Mode
.138
On Board Diagnosis Logic ....................................138
DTC Confirmation Procedure ...............................139
Page 1197 of 3371
EC-6Revision: August 20072004 QX56 Component Inspection ..........................................503
Removal and Installation ......................................503
DTC P1446 EVAP CANISTER VENT CONTROL
VALVE .....................................................................504
Component Description ........................................504
CONSULT-II Reference Value in Data Monitor Mode
.504
On Board Diagnosis Logic ....................................504
DTC Confirmation Procedure ...............................505
Wiring Diagram .....................................................506
Diagnostic Procedure ...........................................507
Component Inspection ..........................................508
DTC P1564 ICC STEERING SWITCH ....................510
Component Description ........................................510
CONSULT-II Reference Value in Data Monitor Mode
.510
On Board Diagnosis Logic ....................................510
DTC Confirmation Procedure ...............................510
Wiring Diagram .....................................................512
Diagnostic Procedure ...........................................514
Component Inspection ..........................................516
DTC P1564 ASCD STEERING SWITCH ................517
Component Description ........................................517
CONSULT-II Reference Value in Data Monitor Mode
.517
On Board Diagnosis Logic ....................................517
DTC Confirmation Procedure ...............................518
Wiring Diagram .....................................................519
Diagnostic Procedure ...........................................521
Component Inspection ..........................................522
DTC P1568 ICC FUNCTION ...................................524
On Board Diagnosis Logic ....................................524
DTC Confirmation Procedure ...............................524
Diagnostic Procedure ...........................................524
DTC P1572 ICC BRAKE SWITCH ..........................525
Component Description ........................................525
CONSULT-II Reference Value in Data Monitor Mode
.525
On Board Diagnosis Logic ....................................525
DTC Confirmation Procedure ...............................525
Wiring Diagram .....................................................527
Diagnostic Procedure ...........................................528
Component Inspection ..........................................532
DTC P1572 ASCD BRAKE SWITCH ......................534
Component Description ........................................534
CONSULT-II Reference Value in Data Monitor Mode
.534
On Board Diagnosis Logic ....................................534
DTC Confirmation Procedure ...............................535
Wiring Diagram .....................................................536
Diagnostic Procedure ...........................................537
Component Inspection ..........................................541
DTC P1574 ICC VEHICLE SPEED SENSOR .........542
Component Description ........................................542
On Board Diagnosis Logic ....................................542
DTC Confirmation Procedure ...............................542
Diagnostic Procedure ...........................................543
DTC P1574 ASCD VEHICLE SPEED SENSOR .....544
Component Description ........................................544On Board Diagnosis Logic .................................... 544
DTC Confirmation Procedure ................................ 544
Diagnostic Procedure ............................................ 545
DTC P1706 PNP SWITCH ....................................... 546
Component Description ........................................ 546
CONSULT-II Reference Value in Data Monitor Mode
. 546
On Board Diagnosis Logic .................................... 546
DTC Confirmation Procedure ................................ 546
Overall Function Check ......................................... 547
Wiring Diagram ..................................................... 548
Diagnostic Procedure ............................................ 549
DTC P1805 BRAKE SWITCH ................................. 551
Description ............................................................ 551
CONSULT-II Reference Value in Data Monitor Mode
. 551
On Board Diagnosis Logic .................................... 551
DTC Confirmation Procedure ................................ 551
Wiring Diagram ..................................................... 552
Diagnostic Procedure ............................................ 553
Component Inspection .......................................... 555
DTC P2122, P2123 APP SENSOR ......................... 556
Component Description ........................................ 556
CONSULT-II Reference Value in Data Monitor Mode
. 556
On Board Diagnosis Logic .................................... 556
DTC Confirmation Procedure ................................ 557
Wiring Diagram ..................................................... 558
Diagnostic Procedure ............................................ 559
Component Inspection .......................................... 561
Removal and Installation ....................................... 561
DTC P2127, P2128 APP SENSOR ......................... 562
Component Description ........................................ 562
CONSULT-II Reference Value in Data Monitor Mode
. 562
On Board Diagnosis Logic .................................... 562
DTC Confirmation Procedure ................................ 563
Wiring Diagram ..................................................... 564
Diagnostic Procedure ............................................ 565
Component Inspection .......................................... 568
Removal and Installation ....................................... 568
DTC P2135 TP SENSOR ........................................ 569
Component Description ........................................ 569
CONSULT-II Reference Value in Data Monitor Mode
. 569
On Board Diagnosis Logic .................................... 569
DTC Confirmation Procedure ................................ 570
Wiring Diagram ..................................................... 571
Diagnostic Procedure ............................................ 572
Component Inspection .......................................... 575
Removal and Installation ....................................... 575
DTC P2138 APP SENSOR ...................................... 576
Component Description ........................................ 576
CONSULT-II Reference Value in Data Monitor Mode
. 576
On Board Diagnosis Logic .................................... 576
DTC Confirmation Procedure ................................ 577
Wiring Diagram ..................................................... 578
Diagnostic Procedure ............................................ 579
Page 1198 of 3371
EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: August 20072004 QX56 Component Inspection ......................................... 582
Removal and Installation ...................................... 582
IGNITION SIGNAL .................................................. 583
Component Description ........................................ 583
Wiring Diagram .................................................... 584
Diagnostic Procedure ........................................... 589
Component Inspection ......................................... 593
Removal and Installation ...................................... 594
INJECTOR CIRCUIT ............................................... 595
Component Description ........................................ 595
CONSULT-II Reference Value in Data Monitor Mode
. 595
Wiring Diagram .................................................... 596
Diagnostic Procedure ........................................... 597
Component Inspection ......................................... 600
Removal and Installation ...................................... 600
FUEL PUMP CIRCUIT ............................................ 601
Description ........................................................... 601
CONSULT-II Reference Value in Data Monitor Mode
. 601
Wiring Diagram .................................................... 602
Diagnostic Procedure ........................................... 603
Component Inspection ......................................... 606
Removal and Installation ...................................... 606
REFRIGERANT PRESSURE SENSOR ................. 607
Component Description ........................................ 607
Wiring Diagram .................................................... 608
Diagnostic Procedure ........................................... 609
Removal and Installation ....................................... 611
ELECTRICAL LOAD SIGNAL ................................ 612
Description ........................................................... 612
CONSULT-II Reference Value in Data Monitor Mode
. 612
Diagnostic Procedure ........................................... 612
ICC BRAKE SWITCH ............................................. 613
Component Description ........................................ 613
CONSULT-II Reference Value in Data Monitor Mode
. 613
Wiring Diagram .................................................... 614
Diagnostic Procedure ........................................... 615
Component Inspection ......................................... 619
ASCD BRAKE SWITCH ......................................... 621
Component Description ........................................ 621CONSULT-II Reference Value in Data Monitor Mode
.621
Wiring Diagram .....................................................622
Diagnostic Procedure ...........................................623
Component Inspection ..........................................627
ASCD INDICATOR ..................................................628
Component Description ........................................628
CONSULT-II Reference Value in Data Monitor Mode
.628
Wiring Diagram .....................................................629
Diagnostic Procedure ...........................................630
MIL AND DATA LINK CONNECTOR ......................631
Wiring Diagram .....................................................631
EVAPORATIVE EMISSION SYSTEM .....................633
Description ............................................................633
Component Inspection ..........................................636
Removal and Installation ......................................637
How to Detect Fuel Vapor Leakage ......................637
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ....................................................................640
System Description ...............................................640
Diagnostic Procedure ...........................................641
Component Inspection ..........................................643
POSITIVE CRANKCASE VENTILATION ...............645
Description ............................................................645
Component Inspection ..........................................645
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .647
System Description ...............................................647
Component Description ........................................648
SERVICE DATA AND SPECIFICATIONS (SDS) ....649
Fuel Pressure .......................................................649
Idle Speed and Ignition Timing .............................649
Calculated Load Value ..........................................649
Mass Air Flow Sensor ...........................................649
Intake Air Temperature Sensor .............................649
Engine Coolant Temperature Sensor ...................649
A/F Sensor 1 Heater .............................................649
Heated Oxygen sensor 2 Heater ..........................649
Crankshaft Position Sensor (POS) .......................649
Camshaft Position Sensor (PHASE) ....................649
Throttle Control Motor ...........................................649
Injector ..................................................................650
Fuel Pump ............................................................650
Page 1202 of 3371
INDEX FOR DTC
EC-11
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results). This number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*6: 2WD models
*7: Models with ICC systemPW ST P SEN/CIRC P0550 0550 2 —EC-346
SENSOR POWER/CIRC P1229 1229 1×EC-424
TCC SOLENOID/CIRC P0740 0740 2×AT - 11 8
TCM P0700 0700 1×AT- 1 0 8
TCS C/U FUNCTN P1211 1211 2 —EC-408
TCS/CIRC P1212 1212 2 —EC-409
THERMSTAT FNCTN P0128 0128 2×EC-184
TP SEN 1/CIRC P0222 0222 1×EC-236
TP SEN 1/CIRC P0223 0223 1×EC-236
TP SEN 2/CIRC P0122 0122 1×EC-171
TP SEN 2/CIRC P0123 0123 1×EC-171
TP SENSOR P2135 2135 1×EC-569
TURBINE REV S/CIRC P1716 1716 2×AT- 1 3 4
TW CATALYST SYS-B1 P0420 0420 2×EC-267
TW CATALYST SYS-B2 P0430 0430 2×EC-267
VEH SPD SEN/CIR AT*5P0720 0720 2×AT - 11 2
VEH SPEED SEN/CIRC*5P0500 0500 2×EC-340
VENT CONTROL VALVE P0447 0447 2×EC-292
VENT CONTROL VALVE P1446 1446 2×EC-504
Items
(CONSULT-II screen terms)DTC*
1
TripMIL lighting
upReference page
CONSULT-II
GST*
2ECM*3
Page 1204 of 3371
INDEX FOR DTC
EC-13
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56P0304 0304 CYL 4 MISFIRE 2×EC-243
P0305 0305 CYL 5 MISFIRE 2×EC-243
P0306 0306 CYL 6 MISFIRE 2×EC-243
P0307 0307 CYL 7 MISFIRE 2×EC-243
P0308 0308 CYL 8 MISFIRE 2×EC-243
P0327 0327 KNOCK SEN/CIRC-B1 2 —EC-250
P0328 0328 KNOCK SEN/CIRC-B1 2 —EC-250
P0332 0332 KNOCK SEN/CIRC-B2 2 —EC-250
P0333 0333 KNOCK SEN/CIRC-B2 2 —EC-250
P0335 0335 CKP SEN/CIRCUIT 2×EC-255
P0340 0340 CMP SEN/CIRC-B1 2×EC-261
P0420 0420 TW CATALYST SYS-B1 2×EC-267
P0430 0430 TW CATALYST SYS-B2 2×EC-267
P0441 0441 EVAP PURG FLOW/MON 2×EC-271
P0442 0442 EVAP SMALL LEAK 2×EC-276
P0444 0444 PURG VOLUME CONT/V 2×EC-285
P0445 0445 PURG VOLUME CONT/V 2×EC-285
P0447 0447 VENT CONTROL VALVE 2×EC-292
P0451 0451 EVAP SYS PRES SEN 2×EC-299
P0452 0452 EVAP SYS PRES SEN 2×EC-302
P0453 0453 EVAP SYS PRES SEN 2×EC-308
P0455 0455 EVAP GROSS LEAK 2×EC-316
P0456 0456 EVAP VERY SML LEAK 2×EC-324
P0460 0460 FUEL LEV SEN SLOSH 2×EC-334
P0461 0461 FUEL LEVEL SENSOR 2×EC-336
P0462 0462 FUEL LEVL SEN/CIRC 2×EC-338
P0463 0463 FUEL LEVL SEN/CIRC 2×EC-338
P0500 0500
VEH SPEED SEN/CIRC*52×EC-340
P0506 0506 ISC SYSTEM 2×EC-342
P0507 0507 ISC SYSTEM 2×EC-344
P0550 0550 PW ST P SEN/CIRC 2 —EC-346
P0605 0605 ECM 1 or 2× or —EC-351
P0700 0700 TCM 1×AT- 1 0 8
P0705 0705 PNP SW/CIRC 2×AT- 1 0 9
P0710 0710 ATF TEMP SEN/CIRC 2×AT- 1 3 1
P0720 0720
VEH SPD SEN/CIR AT*52×AT - 11 2
P0740 0740 TCC SOLENOID/CIRC 2×AT - 11 8
P0744 0744 A/T TCC S/V FNCTN 2×AT- 1 2 1
P0745 0745 L/PRESS SOL/CIRC 2×AT- 1 2 4
P1031 1031 A/F SEN1 HTR (B1) 2×EC-354
P1032 1032 A/F SEN1 HTR (B1) 2×EC-354
P1051 1051 A/F SEN1 HTR (B2) 2×EC-354
DTC*1
Items
(CONSULT-II screen terms)TripMIL lighting
upReference page
CONSULT-II
GST*
2ECM*3