4WD INFINITI QX56 2004 Factory User Guide

DISASSEMBLY
AT-281
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
36. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with transmission assembly ter-
minal connector and the manual valve notch and manual
plate height.Remove it vertically.
37. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
38. Remove bracket from A/T fluid temperature sensor 2.
39. Remove O-ring from A/T assembly harness connector.
40. Remove rear extension assembly (2WD models) or adapter case assembly (4WD models) according to
the following procedures.
SCIA5308E
SCIA5301E
SCIA5264E
SCIA5155E

AT-282
DISASSEMBLY
Revision: August 20072004 QX56
a.2WD models
i. Remove tightening bolts for rear extension assembly and trans-
mission case.
ii. Remove bracket.
iii. Tap rear extension assembly with soft hammer.
iv. Remove rear extension assembly from transmission case. (With
needle bearing)
b.4WD models
i. Remove tightening bolts for adapter case assembly and trans-
mission case.
ii. Remove bracket.
SCIA5349E
SCIA5028E
SCIA5029E
SCIA5203E

AT-288
DISASSEMBLY
Revision: August 20072004 QX56
63. Remove detent spring and spacer from transmission case.
64. Using snap ring pliers, remove snap ring from transmission
case.
65. Remove servo assembly (with return spring) from transmission
case.
66. Remove return spring from servo assembly.
67. Remove O-rings from servo assembly.
68. Remove parking actuator support from rear extension (2WD
models) or adapter case (4WD models).
SCIA5248E
SCIA2333E
SCIA2334E
SCIA3423E

DISASSEMBLY
AT-289
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
69. Remove parking pawl (with return spring) and pawl shaft from
rear extension (2WD models) or adapter case (4WD models).
70. Remove return spring from parking pawl.
71. Remove needle bearing from rear extension (2WD models) or
adapter case (4WD models).
72. Remove rear oil seal from rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Be careful not to scratch rear extension (2WD models) or
adapter case (4WD models).
SCIA3424E
SCIA2445E
SCIA5221E
SCIA5272E

AT-314
ASSEMBLY
Revision: August 20072004 QX56
24. Install revolution sensor to transmission case. Tighten revolution
sensor mounting bolt to the specified torque. Refer to AT-261,
"Components" .
CAUTION:

Do not subject it to impact by dropping or hitting it.

Be careful not to damage harness with the edge of case.

Do not allow metal filings, etc., to get on the sensor's
front edge magnetic area.

Do not place in an area affected by magnetism.
25. As shown in the right figure illustration, use a drift to drive rear
oil seal into the rear extension (2WD models) or adapter case
(4WD models) until it is flush.
CAUTION:

Apply ATF to rear oil seal.

Do not reuse rear oil seal.
26. Install return spring to parking pawl.
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
SCIA2320E
SCIA5270E
SCIA2445E
SCIA3424E

ASSEMBLY
AT-315
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
28. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
29. Install needle bearing to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:

Do not reuse seal rings.

Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
32. Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
SCIA3423E
SCIA5221E
SCIA5209E
SCIA5247E
SCIA5030E

AT-316
ASSEMBLY
Revision: August 20072004 QX56
33. Install bearing race in output shaft.
34. Install rear extension assembly (2WD models) or adapter case assembly (4WD models) according to the
following procedures.
a.2WD models
i. Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to GI-45, "
Recommended Chemical Prod-
ucts and Sealants" .) to rear extension assembly as shown in
illustration.
CAUTION:
Complete remove all moisture, oil and old sealant, etc.
From the transmission case and rear extension assembly
mounting surfaces.
ii. Install rear extension assembly to transmission case.
iii. Install bracket.
iv. Tighten rear extension assembly mounting bolts to specified
torque.
CAUTION:
Do not reuse self-sealing bolt.
SCIA5245E
SCIA5212E
SCIA5029E
Rear extension assembly mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA5349E

ASSEMBLY
AT-317
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
b.4WD models
i. Install gasket to transmission case.
CAUTION:

Do not reuse gasket.

Complete remove all moisture, oil and old gasket, etc.
From the transmission case and adapter case assembly
mounting surfaces.
ii. Install adapter case assembly to transmission case.
iii. Install bracket.
iv. Tighten adapter case assembly mounting bolts to specified
torque.
CAUTION:
Do not reuse self-sealing bolt.
35. Install needle bearing in drum support edge surface.
CAUTION:
Apply petroleum jelly to needle bearing.
SCIA5231E
SCIA5205E
Adapter case assembly mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA5203E
SCIA5198E

TROUBLE DIAGNOSIS
BRC-35
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: August 20072004 QX56
×: Applicable
–: Not applicableVDC SIGNAL
(ON/OFF)––×VDC operation (ON/OFF) status is
displayed.
EBD WARN LAMP – –×Brake warning lamp (ON/OFF) sta-
tus is displayed.
SLCT LVR POSI×××Shift position judged by PNP switch
signal.
R POSI SIG – –×Shift position judged by PNP switch
signal.
4WD FAIL REQ – –×The state of 4WD controller is dis-
played by CAN communication sig-
nal.
2WD/4WD – –×It recognizes on software whether it
is 2WD and whether it is in 4WD
state.
BST OPER SIG – –×Active booster operation (ON/OFF)
status is displayed.
PRESS SENSOR×–×Brake pressure detected by pres-
sure sensor is displayed.
CRANKING SIG – –×The input state of the key SW
START position signal is displayed.
PRESS SEN 2 – –×Brake pressure detected by pres-
sure sensor is displayed.
DELTA S SEN – –×The amount of stroke sensor move-
ments in the active booster
detected by DELTA S SEN is dis-
played.
RELEASE SW NO – –×Release switch signal (ON/OFF)
status is displayed. "ON" indicates
that the brake pedal is depressed.
"OFF" is that the brake pedal is
released.
RELEASE SW NC – –×Release switch signal (ON/OFF)
status is displayed. "OFF" indi-
cates that the brake pedal is
depressed on. "ON" is that the
brake pedal is released.
OHB FAIL – –×OHB fail status is displayed.
HBA FAIL – –×HBA fail status is displayed.
OHB SIG – –×OHB operation (ON/OFF) status is
displayed.
HBA SIG – –×HBA operation (ON/OFF) status is
displayed.
PRES CTRL ACC – –×Pressure control state (ON/OFF) is
displayed. It is applied only to an
ICC vehicle.
PRES FAIL ACC – –×Pressure control fail state (ON/
OFF) is displayed. It is applied only
to an ICC vehicle.
STP OFF RLY – –×Stop lamp relay signal (ON/OFF)
status is displayed. Item
(Unit)Data monitor item selection
Remarks
ECU INPUT
SIGNALSMAIN
SIGNALSSELECTION
FROM MENU

WARNING LAMPS
DI-37
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
4WD Models
WKWA3061E