oil level INFINITI QX56 2004 Factory Service Manual

2004
QUICK REFERENCE CHART: QX56

Disc Brake - Repair LimitsELS000ZU
Unit: mm (in)
Brake PedalELS000ZV
Unit: mm (in)
Refill CapacitiesELS000YO
Brake model CLZ31VC (Front) AD14VE (Rear)
Brake PadStandard thickness (new) 11.88 (0.468) 12.13 (0.478)
Repair limit thickness 1.0 (0.039) 1.0 (0.039)
Disc rotor Standard thickness (new) 26.0 (1.024) 14.0 (0.551)
Repair limit thickness 24.5 (0.965) 12.0 (0.472)
Maximum uneven wear (measured at 8 positions) 0.015 (0.0006) 0.015 (0.0006)
Runout limit (with it attached to the vehicle) 0.04 (0.0016) 0.05 (0.0020)
Brake pedal height (from dash lower panel top surface) 182.3
− 192.3 (7.18 − 7.57)
Depressed pedal height [under a force of 490 N (50 kg, 110 lb) with engine running] More than 90.3 (3.55)
Clearance between stopper rubber and the threaded end of stop lamp switch 0.74 − 1.96 (0.029 − 0.077)
Pedal play 3 − 11 (0.12 − 0.43)
Description Capacity (Approximate)
Metric US measure Imp measure
Fuel 105.8 28 gal 23 1/4 gal
Engine oil
Drain and refill With oil filter change
6.2 6 1/2 qt 5 1/2 qt
Without oil filter change 5.9 6 1/4 qt 5 1/4 qt
Dry engine (engine overhaul) 7.6 8 qt 6 3/4 qt
Cooling system With reservoir at MAX level 14.4 3 3/4 gal 3 1/8 gal
Automatic transmission fluid (ATF) 10.6 11 1/4 qt 9 3/8 qt
Rear final drive oil 1.75 3 3/4 pt 3 1/8 pt
Transfer fluid 3.0 3 1/8 qt 2 5/8 qt
Front final drive oil 1.6 3 3/8 pt 2 7/8 pt
Power steering fluid (PSF) 1.0 1 1/8 qt 7/8 qt
Windshield washer fluid 4.5 1 1/4 gal 1 gal
Air conditioning system refrigerant 1.08 ± 0.05 kg 2.38 ± 0.11 lb 2.38 ± 0.11 lb
Air conditioning system lubricants 290 m9.8 fl oz 10.2 fl oz

ACS-12
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: August 20072004 QX56
LASER BEAM AIMING ADJUSTMENTPFP:00026
Outline of Laser Beam Aiming Adjustment ProcedureEKS007TI
CAUTION:

The laser beam aiming adjustment cannot be performed without CONSULT-II.

The laser beam aiming adjustment must be performed every time the ICC sensor is removed,
installed or has been moved as a result of a collision.
1. Prepare the vehicle and the work area.
2. Set up the ICC target board.
3. Adjust the sensor following the procedure on CONSULT-II.
4. Check system operation after the adjustment.
PreparationEKS007PC

Place the vehicle on level ground. Shift the transmission into "P" position and release the parking brake.

Adjust the tire pressure to the specified value.

See that there is no load in the vehicle. Coolant, engine oil and fuel should be filled to correct level.

Check that the vehicle suspension has been adjusted to the standard height by the load leveling rear air
suspension system. Refer to RSU-12, "
Basic Inspection" .

Clean the ICC sensor with a soft cloth.
Setting up the ICC Target BoardEKS007PE
CAUTION:
Accuracy in setting up the ICC target board is essential for the laser beam aiming adjustment.
ADJUSTING HEIGHT OF THE ICC TARGET BOARD
1. Attach a triangle scale as shown.Tool number : KV99110100 (J-45718)
WKIA1848E
WKIA1849E

AT-58
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
Inspections Before Trouble DiagnosisUCS002CX
A/T FLUID CHECK
Fluid Leakage and Fluid Level Check

Inspect for fluid leakage and check the fluid level. Refer to AT - 1 3 , "Checking A/T Fluid" .
Fluid Condition Check
Inspect the fluid condition.
STALL TEST
Stall Test Procedure
1. Inspect the amount of engine oil. Replenish the engine oil if necessary.
2. Drive for about 10 minutes to warm up the vehicle so that the A/
T fluid temperature is 50 to 80°C (122 to 176°F). Inspect the
amount of ATF. Replenish if necessary.
3. Securely engage the parking brake so that the tires do not turn.
4. Engine start, apply foot brake, and place selector lever in “D”
position.
5. While holding down the foot brake, gradually press down the
accelerator pedal.
6. Quickly read off the stall speed, then quickly remove your foot
from the accelerator pedal.
CAUTION:
Do not hold down the accelerator pedal for more than 5 sec-
onds during this test.
7. Move the selector lever to the “N” position.
8. Cool down the ATF.
Fluid condition Conceivable Cause Required Operation
Varnished (viscous
varnish state)Clutch, brake
scorchedReplace the ATF and check the A/T
main unit and the vehicle for mal-
functions (wire harnesses, cooler
pipes, etc.)
Milky white or
cloudyWater in the fluidReplace the ATF and check for
places where water is getting in.
Large amount of
metal powder mixed
inUnusual wear of
sliding parts within
A/TReplace the ATF and check for
improper operation of the A/T.
SAT6 3 8A
SAT6 4 7B
SCIA1224E
SAT5 1 4G

TROUBLE DIAGNOSIS
AT-63
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
4. CHECK “N” POSITION FUNCTIONS
1. Start the engine.
2. Move selector lever to “N” position.
3. Release the parking brake.
Does vehicle move forward or backward?
YES >> Enter a check mark at “Vehicle moves in “N” position” on the diagnostics worksheet, then continue
the road test.
NO >> GO TO 5.
5. CHECK SHIFT SHOCK
1. Engage the brake.
2. Move selector lever to “D” position.
When the transmission is shifted from
“N” to “D”, is there an excessive shock?
YES >> Enter a check mark at “Large shock when shifted from N to D” on the diagnostics worksheet, then
continue the road test.
NO >> GO TO 6.
6. CHECK “R” POSITION FUNCTIONS
1. Engage the brake.
2. Move selector lever to “R” position.
3. Disengage the brake for 4 to 5 seconds.
Does the vehicle creep backward?
YES >> GO TO 7.
NO >> Enter a check mark at “Vehicle does not creep backward in R position” on the diagnostics work-
sheet, then continue the road test.
7. CHECK “D” POSITION FUNCTIONS
Inspect whether the vehicle moves forward when the transmission is put into the “D” position.
Does the vehicle creep forward in the
“D” positions?
YES >> Go to AT- 6 3 , "Cruise Test - Part 1" , AT- 6 5 , "Cruise Test - Part 2" , and AT- 6 6 , "Cruise Test - Part
3" .
NO >> Enter a check mark at “Vehicle does not move forward in D positions” on the diagnostics work-
sheet, then continue the road test.
Cruise Test - Part 1UCS002D0
1. CHECK STARTING OUT FROM D1
1. Drive the vehicle for about 10 minutes to warm up the engine oil and ATF.
Appropriate temperature for the ATF: 50 - 80°C (122 - 176°F)
2. Park the vehicle on a level surface.
3. Move selector lever to “P” position.
4. Start the engine.
5. Move selector lever to “D” position.
6. Press the accelerator pedal about half way down to accelerate the vehicle.
With CONSULT-II
Read off the gear positions.
Starts from D1?
YES >> GO TO 2.
NO >> Enter a check mark at “Vehicle cannot be started from D1” on the diagnostics worksheet, then
continue the road test.

TROUBLE DIAGNOSIS
AT-75
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
22
Slips/Will
Not
EngageWhen “D” position,
remains in 5th gear.ON vehicle1. Fluid level and stateAT- 5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6

3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5
,
AT- 1 5 1
4. Line pressure testAT- 5 9
5. CAN communication lineAT- 1 0 3
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Front brake (brake band)AT- 2 7 38. Input clutchAT- 2 9 5
9. Gear systemAT- 2 6 1
10. High and low reverse clutchAT- 3 0 5
23Vehicle cannot be
started from D
1 .
Refer toAT- 2 0 3 , "
Vehi-
cle Cannot Be Started
From D1" .ON vehicle1. Fluid level and stateAT- 5 8
2. Accelerator pedal position sensorAT- 1 2 9
3. Line pressure testAT- 5 9
4. CAN communication lineAT- 1 0 3
5. Control valve with TCMAT- 2 4 1
OFF vehicle6. Torque converterAT- 2 7 3
7. Oil pump assemblyAT- 2 9 0
8. 3rd one-way clutchAT- 2 9 2
9. 1st one-way clutchAT- 3 0 0
10. Gear systemAT- 2 6 1
11. Reverse brakeAT- 2 7 3
12. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8
, AT-1 9 .)AT- 2 7 3
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
24Does not lock-up.
Refer to AT- 2 1 5 , "A/T
Does Not Perform
Lock-up" .ON vehicle1. Fluid level and stateAT- 5 8
2. Line pressure testAT- 5 9
3. Engine speed signalAT- 11 5
4. Turbine revolution sensorAT- 1 3 4
5. Torque converter clutch solenoid valveAT- 11 8
6. CAN communication lineAT- 1 0 3
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 39. Oil pump assemblyAT- 2 9 0
No. Items Symptom Condition Diagnostic ItemReference
page

AT-76
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
25
Slips/Will
Not
engageDoes not hold lock-up
condition.
Refer toAT- 2 1 7 , "A/T
Does Not Hold Lock-
up Condition" .ON vehicle1. Fluid level and stateAT-5 8
2. Line pressure testAT-5 9
3. Engine speed signalAT - 11 5
4. Turbine revolution sensorAT- 1 3 4
5. Torque converter clutch solenoid valveAT - 11 8
6. CAN communication lineAT- 1 0 3
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 39. Oil pump assemblyAT- 2 9 0
26Lock-up is not
released.
Refer toAT- 2 1 9 ,
"Lock-up Is Not
Released" .ON vehicle1. Fluid level and stateAT-5 8
2. Line pressure testAT-5 9
3. Engine speed signalAT - 11 5
4. Turbine revolution sensorAT- 1 3 4
5. Torque converter clutch solenoid valveAT - 11 8
6. CAN communication lineAT- 1 0 3
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 39. Oil pump assemblyAT- 2 9 0
27No shock at all or the
clutch slips when
vehicle changes
speed D
1 → D2 . ON vehicle1. Fluid level and stateAT-5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
4. CAN communication lineAT- 1 0 3
5. Line pressure testAT-5 9
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Torque converterAT- 2 7 3
8. Oil pump assemblyAT- 2 9 0
9. 3rd one-way clutchAT- 2 9 2
10. Gear systemAT- 2 6 1
11. Direct clutchAT- 3 0 7
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-77
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
28
Slips/Will
Not
engageNo shock at all or the
clutch slips when
vehicle changes
speed D
2 → D3 .ON vehicle1. Fluid level and stateAT- 5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4,
AT- 1 6 3
4. CAN communication lineAT- 1 0 3
5. Line pressure testAT- 5 9
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Torque converterAT- 2 7 3
8. Oil pump assemblyAT- 2 9 0
9. 3rd one-way clutchAT- 2 9 2
10. Gear systemAT- 2 6 1
11. High and low reverse clutchAT- 3 0 5
12. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8
, AT-1 9 .)AT- 2 7 3
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
29No shock at all or the
clutch slips when
vehicle changes
speed D
3 → D4 .ON vehicle1. Fluid level and stateAT- 5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 7 8,
AT- 1 4 5

4. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5
,
AT- 1 5 1
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT- 5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. Input clutchAT- 2 9 5
11. Gear systemAT- 2 6 1
12. High and low reverse clutchAT- 3 0 5
13. Direct clutchAT- 3 0 7
No. Items Symptom Condition Diagnostic ItemReference
page

AT-78
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
30
Slips/Will
Not
engageNo shock at all or the
clutch slips when
vehicle changes
speed D
4 → D5 .ON vehicle1. Fluid level and stateAT-5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT-5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. Front brake (brake band)AT- 2 7 3
11. Input clutchAT- 2 9 5
12. Gear systemAT- 2 6 1
13. High and low reverse clutchAT- 3 0 5
31When you press the
accelerator pedal and
shift speed D5 → D4
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT-5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT-5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. Input clutchAT- 2 9 5
11. Gear systemAT- 2 6 1
12. High and low reverse clutchAT- 3 0 5
13. Direct clutchAT- 3 0 7
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-79
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
32
Slips/Will
Not
engageWhen you press the
accelerator pedal and
shift speed D4 → D3
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 7 8,
AT- 1 4 5
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT- 5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converter AT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. 3rd one-way clutchAT- 2 9 2
11. Gear systemAT- 2 6 1
12. High and low reverse clutchAT- 3 0 5
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8
, AT-1 9 .)AT- 2 7 3
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
33When you press the
accelerator pedal and
shift speed D3 → D2
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4,
AT- 1 6 3
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT- 5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. 3rd one-way clutchAT- 2 9 2
11. Gear systemAT- 2 6 1
12. Direct clutchAT- 3 0 7
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

AT-80
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
34
Slips/Will
Not
EngageWhen you press the
accelerator pedal and
shift speed D2 → D1
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT-5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
4. CAN communication lineAT- 1 0 3
5. Line pressure testAT-5 9
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Torque converterAT- 2 7 3
8. Oil pump assemblyAT- 2 9 0
9. 3rd one-way clutchAT- 2 9 2
10. 1st one-way clutchAT- 3 0 0
11. Gear systemAT- 2 6 1
12. Reverse brakeAT- 2 7 3
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
35With selector lever in
“D” position, accelera-
tion is extremely poor.ON vehicle1. Fluid level and stateAT-5 8
2. Line pressure testAT-5 9
3. Accelerator pedal position sensorAT- 1 2 9
4. CAN communication lineAT- 1 0 3
5. PNP switchAT- 1 0 9
6. Control cable adjustmentAT- 2 3 4
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. 1st one-way clutchAT- 3 0 0
11. Gear systemAT- 2 6 1
12. Reverse brakeAT- 2 7 3
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page