INFINITI QX56 2004 Factory Service Manual

GW-96
REAR WINDOW DEFOGGER
Revision: August 20072004 QX56
3. CHECK DOOR MIRROR DEFOGGER
Check continuity between door mirror RH terminals 10 and 11.
OK or NG
OK >> Repair or replace harness.
NG >> Replace door mirror RH.
Rear Window Defogger Signal CheckEIS002W6
1. CHECK AV COMMUNICATION LINE
AV communication line check is executed. Refer to AT C - 3 2 , "
CAN Communication System Description" .
OK or NG
OK >> GO TO 2.
NG >> Replace display control unit.
2. CHECK CAN COMMUNICATION LINE
CAN communication line check is executed. Refer to LAN-5, "
CAN COMMUNICATION" .
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> In addition, it is necessary to check CAN communication line. Refer to LAN-5, "
CAN COMMUNI-
CATION" .
Filament CheckEIS002W7
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe.Then press the foil against the wire with your finger.
2. Attach probe circuit tester (in Volt range) to middle portion of
each filament.10 - 11 : Continuity should exist.
LIIA2305E
Is rear window defogger displayed on the display?
SEL122R
SEL263

REAR WINDOW DEFOGGER
GW-97
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: August 20072004 QX56
3. If a filament is burned out, circuit tester registers 0 or battery
voltage.
4. To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
Filament RepairEIS002W8
REPAIR EQUIPMENT

Conductive silver composition (DuPont No. 4817 or equivalent)

Ruler 30 cm (11.8 in) long

Drawing pen

Heat gun

Alcohol

Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
SEL265
PIIA0215E
SEL012D

GW-98
REAR WINDOW DEFOGGER
Revision: August 20072004 QX56
5. Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
SEL013D

DOOR MIRROR
GW-99
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: August 20072004 QX56
DOOR MIRRORPFP:96301
Wiring Diagram — MIRROR —EIS002W9
WIWA0641E

GW-100
DOOR MIRROR
Revision: August 20072004 QX56
Door Mirror AssemblyEIS002WA
REMOVAL
NOTE:
Be careful not to damage the mirror bodies.
1. Remove the front door sash cover. Refer to AV- 4 6 , "
Removal and Installation of Front Tweeter" .
2. Remove the door mirror harness connector.
3. Remove the door mirror mounting nuts and the mirror assembly.
INSTALLATION
Installation is in the reverse order of removal.
Door Mirror GlassEIS002WB
REMOVAL
1. Set mirror assembly mirror glass upward.
2. Apply protective tape to mirror housing.
3. Insert a screwdriver at notch and gently pry mirror glass and
holder from mirror holder bracket.
4. Disconnect two electrical connectors from mirror glass and
holder.
LIIA1570E
LIIA1591E

DOOR MIRROR
GW-101
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: August 20072004 QX56
INSTALLATION
1. Set mirror holder bracket and mirror glass and holder in the hor-
izontal position.
2. Connect two electrical connectors to the back of the mirror
holder.
3. Align mirror glass and holder with mirror holder bracket and
push mirror glass and holder onto mirror holder bracket.
4. Rotate mirror to ensure proper installation.
LIIA1592E

GW-102
DOOR MIRROR
Revision: August 20072004 QX56

IDX-1
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
M INDEX
SECTION IDX

IDX-2
ALPHABETICAL INDEX
Numerics
2-4WD shift solenoid valve ................................ TF-95
4LO indicator lamp ............................................. TF-90
4WD shift indicator lamp .................................... TF-85
4WD shift switch ................................................ TF-95
4WD solenoid valve ........................................... TF-95
4WD warning lamp ............................................ TF-13
A
A/C air flow ...................................................... ATC-29
A/C compressor clutch removal and installation .. ATC-
167
A/C compressor mounting ............................. ATC-166
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-14
A/C control operation (auto A/C) ...................... ATC-26
A/C diagnostic work flow (auto A/C) .............. ATC-120
A/C evaporator ............................................... ATC-175
A/C HFC134a (R134a) system identification ..... ATC-7
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure ATC-
162
A/C HFC134a (R134a) system service tools ... ATC-14
A/C HFC134a system service equipment precaution ...
ATC-11
A/C lubricant (R134a) ...................................... ATC-22
A/C lubrication oil ............................................. ATC-22
A/C operational check ....................... ATC-56, ATC-59
A/C self-diagnoses (auto A/C) ........ ATC-53, ATC-120
A/C service data specification ........................ ATC-182
A/C trouble diagnoses (auto A/C) .................... ATC-33
A/C, A - Wiring diagram ................................... ATC-41
A/T - Wiring diagram .......................................... AT-52
A/T fluid checking ...................... AT-13, AT-58, MA-21
A/T fluid cooler cleaning .................................... AT-15
A/T fluid replacement ............................. AT-13, MA-23
A/T fluid temperature sensor ........................... AT-131
A/T IND - Wiring diagram .................................... DI-41
A/T indicator ........................................................ DI-41
A/T shift lock system ........................................ AT-236
A/T trouble diagnoses ........................................ AT-43
ABS - Wiring diagram ..................................... BRC-16
ABS (anti-lock brake system) ........................... BRC-7
Accelerator control system ............................... ACC-2
Accelerator pedal position (APP) sensor . EC-556, EC-
562, EC-576
Accelerator pedal released position learning ..... EC-44
AF1B1-Wiring diagram EC-431, EC-439, EC-447, EC-
456, EC-466, EC-475, EC-487
AF1B2-Wiring diagram EC-433, EC-441, EC-449, EC-
458, EC-468, EC-477, EC-489
AF1HB1-Wiring diagram .................................. EC-355
AF1HB2-Wiring diagram .................................. EC-357
Aiming adjustment .................................. LT-31, LT-78
Air bag .............................................................. SRS-3
Air cleaner and air duct ..................................... EM-14
Air cleaner filter replacement ............................ MA-15
Air conditioner cut control ................................. EC-30
Air flow meter - See Mass air flow sensor EC-146, EC-
154
Air fuel ratio sensor 1 .. EC-429, EC-437, EC-445, EC-
454, EC-463, EC-472, EC-484
Air fuel ratio sensor 1 heater ........................... EC-354
Air mix. door motor .......................................... ATC-67
All - mode 4WD system ..................................... TF-10
Ambient sensor ............................. ATC-125, ATC-136
Angular tightening application ............................. EM-3
APPS1 - Wiring diagram ................................. EC-558
APPS2 - Wiring diagram ................................. EC-564
APPS3 - Wiring diagram ................................. EC-578
ASC/BS - Wiring diagram ............................... EC-536
ASC/SW - Wiring diagram .............................. EC-519
ASCBOF - Wiring diagram .............................. EC-622
ASCD .............................................................. EC-647
ASCD (automatic speed control device) ........... ACS-3
ASCD brake switch ........................... EC-534, EC-621
ASCD indicator lamp ....................................... EC-628
ASCD steering switch ..................................... EC-517
ASCIND - Wiring diagram ............................... EC-629
ATP switch ......................................................... TF-96
ATP warning lamp .............................................. TF-89
AUDIO - Wiring diagram .................................... AV-10
AUT/DP - Wiring diagram .................................. SE-19
Auto air conditioner - Wiring diagram .............. ATC-41
Auto anti-dazzling inside mirror ........... GW-76, GW-77
Autolamp ............................................................ LT-47
Automatic amplifier ......................................... ATC-60
Automatic transmission number .......................... GI-48
AV and NAVI control unit ................................... AV-63
AV communication line ...................................... AV-87
B
Back door trim ..................................................... EI-31
Back sonar .......................................................... DI-59
BACK/L - Wiring diagram ................................. LT-106
Back-up lamp ................................................... LT-106
Ball joint (front) ................................................ FSU-15
Basic inspection ................................................ EC-79
Battery ................................................................. SC-4
Battery/Starting/Charging System Tester SC-6, SC-12,
SC-19
BCM (Body control module) .............................. BCS-3
Block heater ...................................................... EM-73
Blower motor ................................... ATC-83, ATC-140
Body alignment ................................................ BL-174
Body component parts ..................................... BL-161
Body construction ............................................ BL-173
Body exterior paint color .................................. BL-160
Body mounting ................................................. BL-159
Body repair ....................................................... BL-160
Body sealing .................................................... BL-170
Brake booster .................................................... BR-17
Brake fluid level ................................................. MA-27
Brake hydraulic line ........................................... BR-12
Brake inspection ............................................... MA-28

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Brake lines and cables inspection ..................... MA-27
Brake master cylinder ....................................... BR-15
Brake switch .................................................... EC-551
BRK/SW - Wiring diagram ............................... EC-552
Bulb specifications ........................................... LT-170
Bumper, front ...................................................... EI-13
Bumper, rear ....................................................... EI-15
C
Cabin air filter .................................................... MA-20
Camshaft ........................................................... EM-43
Camshaft inspection .......................................... EM-47
Camshaft position sensor (PHASE) ................ EC-261
CAN - Wiring diagram EC-136, LAN-18, LAN-52, LAN-
92, LAN-128
CAN (Controller Area Network) .. WT-9, BRC-10, LAN-
16, LAN-50, LAN-90, LAN-126
CAN communication . EC-31, EC-135, AT-103, WT-9,
BRC-10
, LAN-16, LAN-50, LAN-90, LAN-126
Canister-See EVAP canister ........................... EC-636
Center case (Transfer) ..................................... TF-113
CHARGE - Wiring diagram ............................... SC-18
Charging system ............................................... SC-17
Chassis and body maintenance ........................ MA-20
Chassis and body maintenanceSchedule 1 ........ MA-7
Chassis and body maintenanceSchedule 2 ........ MA-9
CHIME - Wiring diagram ..................................... DI-46
Circuit breaker ................................................... PG-67
Clock ................................................................... DI-70
CLOCK - Wiring diagram .................................... DI-70
Closed loop control ........................................... EC-27
Closed loop control (Bank 1) ........................... EC-407
Closed loop control (Bank 2) ........................... EC-407
Clutch drum (Transfer) ..................................... TF-116
Clutch force release limit adjustment ................. TF-42
Clutch pressure switch (Transfer) ...................... TF-95
Coil spring (front) ............................................. FSU-10
Collision diagnosis .......................................... SRS-60
Combination lamp, front, removal and installation . LT-
33
Combination lamp, rear, removal and installation .. LT-
122
Combination meter ................................................ DI-5
Combination switch ............................................ LT-97
COMBSW - Wiring diagram ............................... LT-97
COMM - Wiring diagram ................................... AV-87
COMPAS - Wiring diagram ................................. DI-27
Compass ............................................................. DI-26
Component Location (auto A/C) ...................... ATC-37
Compressor clutch removal and installation . ATC-167
Compressor mounting ................................... ATC-166
Compressor precaution ................................... ATC-11
Compressor special service tool ..................... ATC-14
Condenser ..................................................... ATC-173
Connecting rod .................................................. EM-91
Connecting rod bearing clearance .................... EM-91
Connecting rod bushing clearance .................... EM-91
Console box - See Instrument panel ................... IP-10
Console box lamp ............................................. LT-152
CONSULT for all-mode 4WD ............................. TF-31
CONSULT for VDC ......................................... BRC-28
CONSULT-II for engine ................................... EC-103
Control units (terminal arrangement) ................. PG-71
Control valve (A/T) ............................................. AT-37
Control valve (Transfer) .................................... TF-119
Controller Area Network (CAN) . WT-9, BRC-10, LAN-
16, LAN-50, LAN-90, LAN-126
Converter housing installation ............ AT-257, AT-260
COOL/F - Wiring diagram ................................ EC-413
Coolant mixture ratio ......................................... MA-11
Coolant replacement ......................................... MA-12
Cooling circuit (engine) ........................................ CO-6
Cooling fan ........................................................ CO-13
Cooling fan control ........................................... EC-410
Cooling fan motor ............................................ EC-419
Cooling unit (A/C evaporator) ....... ATC-144, ATC-175
Corrosion protection ......................................... BL-167
Crankcase ventilation system - See Positive crankcase
ventilation ........................................................ EC-645
Crankshaft ......................................................... EM-74
Crankshaft position sensor (POS) ................... EC-255
Crash zone sensor .......................................... SRS-55
Cylinder block .................................................... EM-73
Cylinder block boring ......................................... EM-94
D
D/LOCK - Wiring diagram ................................... BL-20
Data link connector .......................................... EC-105
Daytime light system .......................................... LT-34
Daytime running light - See Daytime light system .. LT-
34
DEF - Wiring diagram ....................................... GW-82
Diagnosis sensor unit ...................................... SRS-58
Diagnostic trouble code (DTC) .......................... EC-53
Diagnostic trouble code (DTC) for OBD system .. EC-8
Diagnostic trouble code (DTC) inspection priority chart
EC-76
Differential carrier assembly ............................ RFD-11
Differential carrier disassembly ....................... RFD-13
Differential gear oil replacement ........................ MA-25
Dimensions ......................................................... GI-49
Direct clutch solenoid valve ................ AT-157, AT-160
Display and amp.assembly .............................. ATC-60
Display Control Unit ......................................... AV-158
Dome light - See Interior lamp .......................... LT-129
Door glass .......................................... GW-69, GW-72
Door lock .......................................................... BL-132
Door mirror lamp ............................................... LT-129
Door trim .............................................................. EI-31
Door, front ........................................... BL-129, GW-69
Door, rear ........................................... BL-129, GW-72
Drive belt ........................................................... EM-12
Drive chain (Transfer) ....................................... TF-115
Drive pinion diff. inspection .............................. RFD-12
Drive pinion height ........................................... RFD-17
Drive shaft (rear) ................................................ RAX-7