display INFINITI QX56 2006 Factory Service Manual

ATC-58
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Operational Check (Front)EJS003XL
The purpose of the operational check is to confirm that the system operates properly.
CHECKING MEMORY FUNCTION
1. Set the temperature to 90°F or 32 °C.
2. Turn front blower control dial counterclockwise until system shuts OFF.
3. Turn ignition switch OFF.
4. Turn ignition switch ON.
5. Press the AUTO switch.
6. Confirm that the set temperature remains at previous temperature.
7. Turn front blower control counterclockwise until system shuts OFF.
If NG, go to trouble diagnosis procedure for ATC-131, "
Memory Function" .
If OK, continue with next check.
CHECKING BLOWER
1. Turn front blower control clockwise, blower should operate on low speed. The blower symbol should have one blade lit (on display).
2. Turn the front blower control dial again, and continue checking blower speed and blower symbol until all speeds are checked.
3. Leave blower on MAX speed.
If NG, go to trouble diagnosis procedure for AT C - 9 5 , "
DIAGNOSTIC PROCEDURE FOR BLOWER
MOTOR"AT C - 9 5 , "DIAGNOSTIC PROCEDURE FOR BLOWER MOTOR" .
If OK, continue with next check.
CHECKING DISCHARGE AIR
1. Press MODE switch four times and the DEF ( ) switch.
2. Each position indicator should change shape (on display).
3. Confirm that discharge air comes out according to the air distribution table. Refer to AT C - 3 0 , "
Discharge
Air Flow" .
Mode door position is checked in the next step.
If NG, go to trouble diagnosis procedure for AT C - 6 4 , "
Mode Door Motor Circuit" .
If OK, continue the check.
NOTE:
Confirm that the compressor clutch is engaged (sound or visual inspection) and intake door position is at fresh
when the DEF or D/F is selected.
CHECKING RECIRCULATION (, ONLY)
1. Press recirculation ( ) switch one time. Recirculation indicator should illuminate.
2. Press recirculation ( ) switch one more time. Recirculation indicator should go off.
3. Listen for intake door position change (blower sound should change slightly).
If NG, go to trouble diagnosis procedure for AT C - 8 3 , "
Intake Door Motor Circuit" .
If OK, continue the check.
NOTE:
Confirm that the compressor clutch is engaged (sound or visual inspection) and intake door position is at fresh
when the DEF or D/F is selected. REC ( ) is not allowed in DEF ( ) D/F ( ) or FOOT ( ).
CHECKING TEMPERATURE DECREASE
1. Rotate temperature control dial (driver side or passenger side) counterclockwise until 16 °C (60 °F) is dis-
played.
2. Check for cold air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation. If OK, go to trouble diagnosis procedure for ATC-121,
"Insufficient Cooling" . If air mix door motor appears to be malfunctioning, go to AT C - 7 2 , "DIAGNOSTIC PRO-
CEDURE FOR AIR MIX DOOR MOTOR (DRIVER)" or AT C - 7 6 , "DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER)" .
If OK, continue the check. Conditions : Engine running and at normal operating temperature

TROUBLE DIAGNOSISATC-59
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
CHECKING TEMPERATURE INCREASE
1. Rotate temperature control dial clockwise (driver side or passenger side) until 32°C (90 °F) is displayed.
2. Check for hot air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation. If OK, go to trouble diagnosis procedure for ATC-128,
"Insufficient Heating" . If air mix door motor appears to be malfunctioning, go to AT C - 7 2 , "DIAGNOSTIC PRO-
CEDURE FOR AIR MIX DOOR MOTOR (DRIVER)" or AT C - 7 6 , "DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER)" .
If OK, continue with next check.
CHECK A/C SWITCH
1. Press A/C switch when AUTO switch is ON, or in manual mode.
2. A/C switch indicator will turn ON.

Confirm that the compressor clutch engages (sound or visual inspection).
NOTE:
If current mode setting is DEF or D/F, compressor clutch may already be engaged.
If NG, go to trouble diagnosis procedure for AT C - 11 5
.
If OK, continue with next check.
CHECKING AUTO MODE
1. Press AUTO switch.
2. Display should indicate AUTO.

If ambient temperature is warm, and selected temperature is cool, confirm that the compressor clutch
engages (sound or visual inspection). (Discharge air and blower speed will depend on ambient, in-vehi-
cle, and set temperatures.)
If NG, go to trouble diagnosis procedure for AT C - 6 1 , "
Power Supply and Ground Circuit for Front Air Control" ,
then if necessary, trouble diagnosis procedure for AT C - 11 5 , "
Magnet Clutch Circuit" .
If all operational checks are OK (symptom cannot be duplicated), go to malfunction Simulation Tests in AT C -
39, "How to Perform Trouble Diagnosis for Quick and Accurate Repair" and perform tests as outlined to simu-
late driving conditions environment. If symptom appears. Refer to AT C - 3 9 , "
How to Perform Trouble Diagnosis
for Quick and Accurate Repair" , AT C - 3 9 , "SYMPTOM TABLE" and perform applicable trouble diagnosis pro-
cedures.

ATC-62
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
COMPONENT DESCRIPTION
Front Air Control
The front air control has a built-in microcomputer which processes
information sent from various sensors needed for air conditioner
operation. The air mix door motors, mode door motor, intake door
motor, defroster door motor, blower motor and compressor are then
controlled.
The front air control is unitized with control mechanisms. When the
various switches and temperature dials are operated, data is input to
the front air control.
Self-diagnostic functions are also built into the front air control to pro-
vide quick check of malfunctions in the auto air conditioner system.
Potentio Temperature Control (PTC)
There are two PTCs (passenger and driver) built into the front air
control. They can be set at an interval of 0.5°C (1.0 °F) in the 16 °C
(60 °F) to 32 °C (90 °F) temperature range by rotating the temperature
dial. The set temperature is displayed.
DIAGNOSTIC PROCEDURE FOR A/C SYSTEM
SYMPTOM: A/C system does not come on.
WJIA0544E
WJIA1050E
WJIA0414E

ATC-134
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Ambient Sensor CircuitEJS003Y2
COMPONENT DESCRIPTION
Ambient Sensor
The ambient sensor is attached on the radiator core support (left
side). It detects ambient temperature and converts it into a value
which is then input into the front air control.
AMBIENT TEMPERATURE INPUT PROCESS
The front air control includes a processing circuit for the ambient sensor input. However, when the tempera-
ture detected by the ambient sensor increases quickly, the processing circuit retards the front air control func-
tion. It only allows the front air control to recognize an ambient temperature increase of 0.33°C (0.6 °F) per 100
seconds.
This prevents constant adjustments due to momentary conditions, such as stopping after high speed driving.
Although the actual ambient temperature has not changed, the temperature detected by the ambient sensor
will increase. This is because the heat from the engine compartment can radiate to the front grille area, loca-
tion of the ambient sensor.
DIAGNOSTIC PROCEDURE FOR AMBIENT SENSOR
SYMPTOM: Ambient sensor circuit is open or shorted. Using the
CONSULT-II, DTC B257B or B257C is displayed. Without a CON-
SULT-II, code 40 or 41 is indicated on front air control as a result of
conducting the front air control self-diagnosis.
1. CHECK VOLTAGE BETWEEN AMBIENT SENSOR AND GROUND
1. Disconnect ambient sensor connector.
2. Turn ignition switch ON.
3. Check voltage between ambient sensor harness connector E1 terminal 1 and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 4.
WJIA0819E
WJIA0456E
1 - Ground : Approx. 5V
WJIA1273E

ATC-138
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
DIAGNOSTIC PROCEDURE FOR IN-VEHICLE SENSOR
SYMPTOM: In-vehicle sensor circuit is open or shorted. Using the
CONSULT-II, DTC B2578 or B2579 is displayed. Without a CON-
SULT-II code 30, 31, 44 or 46 is indicated on front air control as a
result of conducting self-diagnosis.
1. CHECK IN-VEHICLE SENSOR CIRCUIT
Self-diagnosis DTC B2578 or B2579 (with CONSULT-II) or code 30, 31 44 or 46 (without CONSULT-II) is
present?
YES or NO
YES >> GO TO 6.
NO >> GO TO 2.
2. CHECK VOLTAGE BETWEEN IN-VEHICLE SENSOR AND GROUND
1. Disconnect in-vehicle sensor connector.
2. Turn ignition switch ON.
3. Check voltage between in-vehicle sensor harness connector M32 terminal 4 and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 5.
3. CHECK CIRCUIT CONTINUITY BETWEEN IN-VEHICLE SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between in-vehicle sensor harness connector M32 terminal 1 and front air control harness connector M49 ter-
minal 21.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK IN-VEHICLE SENSOR
Refer to ATC-142, "
Intake Sensor Circuit" .
OK or NG
OK >> 1. Replace front air control. Refer to ATC-144, "FRONT AIR CONTROL" .
2. Go to AT C - 5 6 , "
A/C System Self-diagnosis Function" and perform self-diagnosis.
NG >> 1. Replace in-vehicle sensor. Refer to ATC-146, "
IN-VEHICLE SENSOR" .
2. Go to AT C - 5 6 , "
A/C System Self-diagnosis Function" and perform self-diagnosis.
WJIA0460E
4 - Ground : Approx. 5V.
LJIA0089E
1 - 21 : Continuity should exist.
LJIA0090E

TROUBLE DIAGNOSISATC-141
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
DIAGNOSTIC PROCEDURE FOR OPTICAL SENSOR
SYMPTOM: Optical sensor circuit is open or shorted. Using the
CONSULT-II, DTC B257F or B2580 is displayed. Without a CON-
SULT-II, code 50 or 52 is indicated on front air control as a result of
conducting the front air control self-diagnosis.
1. CHECK CIRCUIT CONTINUITY BETWEEN OPTICAL SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector and optical sensor con- nector.
3. Check continuity between optical sensor harness connector M402 terminal 1 and 2 and front air control harness connector
M50 terminal 31 and 40.
4. Check continuity between optical sensor harness connector M402 terminal 1 and 2 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK CIRCUIT CONTINUITY BETWEEN OPTICAL SENSOR AND BCM
1. Turn ignition switch OFF.
2. Disconnect BCM connector and optical sensor connector.
3. Check continuity between optical sensor harness connector M402 terminal 3 and BCM harness connector M18 terminal 18.
4. Check continuity between optical sensor harness connector M402 terminal 3 and ground.
OK or NG
OK >> Replace optical sensor. Refer to ATC-147, "OPTICAL SENSOR" .
NG >> Repair harness or connector.
WJIA0570E
1 - 31 : Continuity should exist.
2 - 40 : Continuity should exist.
1, 2 - Ground. : Continuity should not exist.
WJIA1445E
3 - 18 : Continuity should exist.
3 - Ground : Continuity should not exist.
WJIA1446E

ATC-142
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Intake Sensor CircuitEJS003Y5
COMPONENT DESCRIPTION
Intake Sensor
The intake sensor is located on the heater & cooling unit. It converts
temperature of air after it passes through the evaporator into a resis-
tance value which is then input to the front air control.
DIAGNOSTIC PROCEDURE FOR INTAKE SENSOR
SYMPTOM: Intake sensor circuit is open or shorted. Using the CON-
SULT-II, DTC B2581 or B2582 is displayed. Without a CONSULT-II,
code 56 or 57 is indicated on front air control as a result of conduct-
ing the front air control self-diagnosis.
1. CHECK VOLTAGE BETWEEN INTAKE SENSOR AND GROUND
1. Disconnect intake sensor connector.
2. Turn ignition switch ON.
3. Check voltage between intake sensor harness connector M146 terminal 2 and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 4.
2. CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector.
3. Check continuity between intake sensor harness connector M146 terminal 1 and front air control harness connector M49 ter-
minal 21.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
WJIA0571E
WJIA0464E
2 - Ground : Approx. 5V
WJIA1375E
1 - 21 : Continuity should exist.
WJIA1376E

ATC-190
REFRIGERANT LINES
Revision: November 20092006 QX56
NOTE:
Keep the probe inserted for at least 10 seconds. Use caution not to contaminate the probe tip with
water or dirt that may be in the drain hose.
5. If a leak is detected, verify at least once by blowing compressed air into the area of the suspected leak, then repeat the leak check.
6. Do not stop when one leak is found. Continue to check for additional leaks at all system components and connections.
7. If no leaks are found, perform steps 8 - 11.
8. Start the engine.
9. Set the heater A/C controls as follows:
NOTE:
For the automatic system, turn OFF the automatic controls and set the heater A/C controls manually.
a. A/C switch to ON
b. Air flow to VENT mode
c. Intake position to RECIRCULATION mode
d. Temperature to MAX cold
e. Blower fan speed to HIGH
10. Run the engine at 1,500 rpm for at least 2 minutes.
11. Turn the engine OFF and perform the leak check again following steps 4 through 6 above.
Refrigerant leaks should be checked immediately after turning
the engine OFF. Begin with the leak detector at the compressor.
The pressure on the high pressure side will gradually drop after
the refrigerant circulation stops and pressure on the low pres-
sure side will gradually rise, as shown in the graph. Some leaks
are more easily detected when the pressure is high.
12. Before connecting the recovery/recycling equipment to the vehicle, check the recovery/recycling equip- ment gauges. No refrigerant pressure should be displayed. If pressure is displayed, recover the refriger-
ant from the equipment lines and then check the refrigerant purity.
13. Confirm refrigerant purity in supply tank using recovery/recycling equipment and refrigerant identifier equipment (J-41810-NI).
14. Confirm the refrigerant purity in the vehicle's A/C system using recovery/recycling equipment and refriger- ant identifier equipment (J-41810-NI).
15. Discharge the A/C system using recovery/recycling equipment. Repair the leaking fitting or component as necessary.
16. Evacuate and recharge the A/C system and perform the leak test to confirm that there are no refrigerant leaks.
17. Conduct the Operational Check to ensure system works properly. Refer to AT C - 5 8 , "
Operational Check
(Front)" and AT C - 6 0 , "Operational Check (Rear)" .
SHA839E

AV-2Revision: November 20092006 QX56
TEM ..................................................................
... 65
Wiring Diagram — H/PHONE — ......................... ... 67
Terminals and Reference Value for Bluetooth Con-
trol Unit ................................................................... 69
Bluetooth Control Unit Self-Diagnosis Function .. ... 71
BLUETOOTH CONTROL UNIT INITIALIZATION
CHECKS ........................................................... ... 71
STARTING THE DIAGNOSTIC MODE ............ ... 71
Power Supply and Ground Circuit Check for Blue-
tooth Control Unit ................................................. ... 72
Removal and Installation ..................................... ... 73
BLUETOOTH CONTROL UNIT ........................ ... 73
BLUETOOTH ON INDICATOR ......................... ... 73
MICROPHONE ................................................. ... 73
DVD ENTERTAINMENT SYSTEM ......................... ... 75
Component Parts and Harness Connector Location ... 75
Description ........................................................... ... 76
Schematic ............................................................ ... 77
Wiring Diagram — DVD — .................................. ... 78
Trouble Diagnosis ................................................ ... 81
Power Supply Circuit Inspection .......................... ... 82
Removal and Installation ..................................... ... 83
DVD PLAYER ...................................................... 83
VIDEO MONITOR ............................................ ... 83
NAVIGATION SYSTEM .......................................... ... 84
System Description .............................................. ... 84
TRAVEL DISTANCE ......................................... ... 84
TRAVEL DIRECTION ....................................... ... 84
MAP-MATCHING .............................................. ... 85
GPS (GLOBAL POSITIONING SYSTEM) ....... ... 85
COMPONENT DESCRIPTION ......................... ... 86
CAN Communication System Description ........... ... 86
Component Parts Location .................................. ... 87
Schematic ............................................................ ... 88
Wiring Diagram — NAVI — .................................. ... 89
Schematic ............................................................ ... 96
Wiring Diagram — COMM — .............................. ... 97
Terminals and Reference Value for NAVI Control
Unit ...................................................................... .100
Terminals and Reference Value for Display Control
unit ....................................................................... .102
Terminals and Reference Value for Display unit .. .106
Terminals and Reference Value for AV Switch .... .108
Terminals and Reference Value for BCM ............. .109
On Board Self-Diagnosis Function ...................... ..111
DESCRIPTION ................................................. ..111
DIAGNOSIS ITEM ............................................ ..111
Self-Diagnosis Mode (DCU) ................................ .112
OPERATION PROCEDURE ............................. .112
SELF–DIAGNOSIS RESULT ............................ .113
Self-Diagnosis Mode (NAVI) ................................ .114
OPERATION PROCEDURE ............................. .114
SELF–DIAGNOSIS RESULT ............................ .115
Confirmation/Adjustment Mode ........................... .117
OPERATION PROCEDURE ............................. .117
DISPLAY DIAGNOSIS ...................................... .118
VEHICLE SIGNALS .......................................... .118
NAVIGATION .................................................... .119
DISPLAY DIAGNOSIS ...................................... .119VEHICLE SIGNALS ..........................................
.120
ERROR HISTORY ............................................ .120
DIAGNOSIS BY ERROR HISTORY ................. .120
NAVIGATION .................................................... .122
CAN DIAG SUPPORT MONITOR ....................... .124
OPERATION PROCEDURE ............................. .124
AV Switch Self-Diagnosis Function ...................... .125
Power Supply and Ground Circuit Check for NAVI
Control Unit .......................................................... .126
Power Supply and Ground Circuit Check for Display
Control Unit .......................................................... .127
Power Supply and Ground Circuit Check for Display
Unit ....................................................................... .128
Power Supply and Ground Circuit Check for AV
Switch .................................................................. .130
Vehicle Speed Signal Check for NAVI Control Unit .131
Vehicle Speed Signal Check for Display Control Unit .132
Illumination Signal Check for NAVI Control Unit .. .133
Illumination Signal Check for Display Control Unit .133
Ignition Signal Check for NAVI Control Unit ......... .133
Ignition Signal Check for Display Control Unit ..... .134
Reverse Signal Check for NAVI Control Unit ....... .134
Reverse Signal Check for Display Control Unit ... .134
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) ..................... .135
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) ......................... .136
Display Communication Line Check (Between Dis-
play Control Unit and Display Unit) ...................... .138
AV Communication Line Check (Between Display
Control Unit and AV Switch) ................................. .139
CAN Communication Line Check ........................ .140
If NAVI Control Unit Detects That DVD-ROM Map
is Not Inserted ...................................................... .140
If NAVI Control Unit Detects That Inserted DVD-
ROM Map is Malfunctioning or If It is Impossible to
Load Data from DVD-ROM Map .......................... .141
If Connection Between NAVI Control Unit and GPS
Antenna is Malfunctioning .................................... .141
Operating Screen for Audio and A/C is Not Dis-
played When Showing NAVI Screen .................... .142
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Bluish) ........................................... .143
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Reddish) ........................................ .144
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Yellowish) ...................................... .145
Color of RGB Image is Not Proper (All Screens Look
Bluish) .................................................................. .146
Color of RGB Image is Not Proper (All Screens Look
Reddish) ............................................................... .147
Color of RGB Image is Not Proper (All Screens Look
Yellowish) ............................................................. .148
NAVI Screen is Rolling ......................................... .150
Guide Sound is Not Heard ................................... .152
Screen is Not Shown ........................................... .153
A/C Screen is Not Shown (NAVI Screen is Shown) .153
FUEL ECONOMY Screen is Not Shown .............. .153
Average Fuel Economy Displayed is Not Shown (“

AV-3
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
*** ” is Shown) .....................................................
. 153
Distance to Empty Displayed is Not Shown (“ *** ”
is Shown) ............................................................ . 154
Driving Distance or Average Speed Displayed is Not
Shown (“ *** ” is Shown) ...................................... . 154
WARNING DOOR OPEN Screen is Not Shown . . 154
Unable to Operate All of AV Switches (Unable to
Start Self-Diagnosis) ........................................... . 155
Audio Does Not Work .......................................... . 155
Navigation System Does Not Activate ................ . 155
Previous NAVI Conditions are Not Stored ........... . 156
Previous Vehicle Conditions are Not Stored ....... . 156
Position of Current Location Mark is Not Correct . 156
Radio Wave From GPS Satellite is Not Received . 156
Driving Test ......................................................... . 157
Example of Symptoms Judged Not Malfunction . . 158
BASIC OPERATION ........................................ . 158
VEHICLE MARK .............................................. . 158
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ............ . 159
VOICE GUIDE .................................................. . 159
ROUTE SEARCH ............................................. . 160
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT ............................................. . 161
CURRENT-LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ....... . 164CURRENT-LOCATION MARK JUMPS ............
.164
CURRENT-LOCATION MARK IS IN A RIVER OR
SEA .................................................................. .165
WHEN DRIVING ON SAME ROAD, SOME-
TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE .............................................................. .165
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ................................................... .165
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ............................... .165
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED ............................................................ .165
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ....... .165
Program Loading of NAVI Control Unit ................ .166
Removal and Installation ..................................... .167
AV SWITCH ...................................................... .167
DISPLAY CONTROL UNIT ............................... .167
DISPLAY UNIT ................................................. .167
GPS ANTENNA ................................................ .167
NAVI CONTROL UNIT ..................................... .168
STEERING WHEEL AUDIO CONTROL
SWITCHES ...................................................... .168