door lock INFINITI QX56 2006 Factory Service Manual

ATC-54
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Front Air Control Terminals and Reference ValueEJS003XJ
Measure voltage between each terminal and ground by following
Terminals and Reference Value for front air control.
PIN CONNECTOR TERMINAL LAYOUT
TERMINALS AND REFERENCE VALUE FOR FRONT AIR CONTROL
WJIA0544E
WJIA0402E
Te r m i -
nal No. Wire
color ItemIgnition
switch Condition Voltage (V)
(Approx.)
1 B Ground -- 0V
2 Y Sensor power ON- 5V
3 W/G Air mix door motor (Driver) CW ON Clockwise rotation Battery voltage
4 G Air mix door motor (Driver) CCW ON Counterclockwise rotation Battery voltage
5 BR/W Mode door motor CW ON Clockwise rotationBattery voltage
6 P/L Mode door motor CCW ON Counterclockwise rotationBattery voltage
7 O Intake door motor CCW ON Counterclockwise rotationBattery voltage
8 G/B Intake door motor CW ON Clockwise rotationBattery voltage
9 L/B Intake sensor ON- 0 - 5V
10 L/R Fan ON signal ON Blower switch OFF
5V
ON Blower switch ON 0V
11 Y/B Rear defroster request ON- Battery voltage
12 W/R Compressor ON signal ON A/C switch OFF
5V
ON A/C switch ON 0V
13 G/R Variable blower control ON- 0 - 5V
14 Y/G Power supply for IGN ON- Battery voltage
15 P Sensor ground ON- 0V
16 GR Mode door motor feedback ON- 0 - 5V
17 P Ambient sensor ON- 0 - 5V
18 SB Air mix door motor (Driver) feedback ON -0 - 5V
19 LG Defroster door motor CW ON Clockwise rotationBattery voltage
20 P/B Defroster door motor CCW ON Counterclockwise rotationBattery voltage
21 V/R Sensor return ON- 0 - 5V

TROUBLE DIAGNOSISATC-55
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
22 Y/R Power supply for BAT-- Battery voltage
23 R/L Illumination + ON Park lamps ONBattery voltage
24 BR Illumination - - Park lamps ON
25 LG/B Defroster door motor feedback ON -0 - 5V
26 R/B Front blower request ONFront blower motor OFF
Battery voltage
Front blower motor ON 0V
27 GR/R Air mix door motor (Rear) CW ON Clockwise rotationBattery voltage
28 L/Y Air mix door motor (Rear) CCW ON Counterclockwise rotation Battery voltage
29 Y/L Water valve ONWater valve open
0V
Water valve closed 5V
30 W/G Water valve ONWater valve open
0V
Water valve closed Battery voltage
31 W/V Optical sensor (Passenger) ON- 0 - 5V
32 LG/R In-vehicle sensor signal ON- 0 - 5V
33 V Air mix door (Rear) set point ON- 0 - 5V
34 L CAN-H ON- 0 - 5V
35 P CAN-L ON- 0 - 5V
36 G/W Air mix door motor (Passenger) CW ON Clockwise rotation Battery voltage
37 L Air mix door motor (Passenger)
CCW ON Counter clockwise rotation
Battery voltage
38 W/L Rear blower request ONFront blower motor OFF
Battery voltage
Front blower motor ON 0V
39 Y/B Rear select signal ON- 0V - Battery voltage
40 G/O Optical sensor (Driver) ON- 0 - 5V
41 R/W Air mix door motor (Passenger)
feedback ON
- 0 - 5V
42 R/Y Air mix door motor (Rear) feedback ON -0 - 5V
43 BR/Y In-vehicle sensor motor (+) ON- Battery voltage
44 O/B In-vehicle sensor motor (-) ON- 0V
Te r m i -
nal No. Wire
color Item
Ignition
switch Condition
Voltage (V)
(Approx.)
PIIA2344E

ATC-58
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Operational Check (Front)EJS003XL
The purpose of the operational check is to confirm that the system operates properly.
CHECKING MEMORY FUNCTION
1. Set the temperature to 90°F or 32 °C.
2. Turn front blower control dial counterclockwise until system shuts OFF.
3. Turn ignition switch OFF.
4. Turn ignition switch ON.
5. Press the AUTO switch.
6. Confirm that the set temperature remains at previous temperature.
7. Turn front blower control counterclockwise until system shuts OFF.
If NG, go to trouble diagnosis procedure for ATC-131, "
Memory Function" .
If OK, continue with next check.
CHECKING BLOWER
1. Turn front blower control clockwise, blower should operate on low speed. The blower symbol should have one blade lit (on display).
2. Turn the front blower control dial again, and continue checking blower speed and blower symbol until all speeds are checked.
3. Leave blower on MAX speed.
If NG, go to trouble diagnosis procedure for AT C - 9 5 , "
DIAGNOSTIC PROCEDURE FOR BLOWER
MOTOR"AT C - 9 5 , "DIAGNOSTIC PROCEDURE FOR BLOWER MOTOR" .
If OK, continue with next check.
CHECKING DISCHARGE AIR
1. Press MODE switch four times and the DEF ( ) switch.
2. Each position indicator should change shape (on display).
3. Confirm that discharge air comes out according to the air distribution table. Refer to AT C - 3 0 , "
Discharge
Air Flow" .
Mode door position is checked in the next step.
If NG, go to trouble diagnosis procedure for AT C - 6 4 , "
Mode Door Motor Circuit" .
If OK, continue the check.
NOTE:
Confirm that the compressor clutch is engaged (sound or visual inspection) and intake door position is at fresh
when the DEF or D/F is selected.
CHECKING RECIRCULATION (, ONLY)
1. Press recirculation ( ) switch one time. Recirculation indicator should illuminate.
2. Press recirculation ( ) switch one more time. Recirculation indicator should go off.
3. Listen for intake door position change (blower sound should change slightly).
If NG, go to trouble diagnosis procedure for AT C - 8 3 , "
Intake Door Motor Circuit" .
If OK, continue the check.
NOTE:
Confirm that the compressor clutch is engaged (sound or visual inspection) and intake door position is at fresh
when the DEF or D/F is selected. REC ( ) is not allowed in DEF ( ) D/F ( ) or FOOT ( ).
CHECKING TEMPERATURE DECREASE
1. Rotate temperature control dial (driver side or passenger side) counterclockwise until 16 °C (60 °F) is dis-
played.
2. Check for cold air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation. If OK, go to trouble diagnosis procedure for ATC-121,
"Insufficient Cooling" . If air mix door motor appears to be malfunctioning, go to AT C - 7 2 , "DIAGNOSTIC PRO-
CEDURE FOR AIR MIX DOOR MOTOR (DRIVER)" or AT C - 7 6 , "DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER)" .
If OK, continue the check. Conditions : Engine running and at normal operating temperature

TROUBLE DIAGNOSISATC-59
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
CHECKING TEMPERATURE INCREASE
1. Rotate temperature control dial clockwise (driver side or passenger side) until 32°C (90 °F) is displayed.
2. Check for hot air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation. If OK, go to trouble diagnosis procedure for ATC-128,
"Insufficient Heating" . If air mix door motor appears to be malfunctioning, go to AT C - 7 2 , "DIAGNOSTIC PRO-
CEDURE FOR AIR MIX DOOR MOTOR (DRIVER)" or AT C - 7 6 , "DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR MOTOR (PASSENGER)" .
If OK, continue with next check.
CHECK A/C SWITCH
1. Press A/C switch when AUTO switch is ON, or in manual mode.
2. A/C switch indicator will turn ON.

Confirm that the compressor clutch engages (sound or visual inspection).
NOTE:
If current mode setting is DEF or D/F, compressor clutch may already be engaged.
If NG, go to trouble diagnosis procedure for AT C - 11 5
.
If OK, continue with next check.
CHECKING AUTO MODE
1. Press AUTO switch.
2. Display should indicate AUTO.

If ambient temperature is warm, and selected temperature is cool, confirm that the compressor clutch
engages (sound or visual inspection). (Discharge air and blower speed will depend on ambient, in-vehi-
cle, and set temperatures.)
If NG, go to trouble diagnosis procedure for AT C - 6 1 , "
Power Supply and Ground Circuit for Front Air Control" ,
then if necessary, trouble diagnosis procedure for AT C - 11 5 , "
Magnet Clutch Circuit" .
If all operational checks are OK (symptom cannot be duplicated), go to malfunction Simulation Tests in AT C -
39, "How to Perform Trouble Diagnosis for Quick and Accurate Repair" and perform tests as outlined to simu-
late driving conditions environment. If symptom appears. Refer to AT C - 3 9 , "
How to Perform Trouble Diagnosis
for Quick and Accurate Repair" , AT C - 3 9 , "SYMPTOM TABLE" and perform applicable trouble diagnosis pro-
cedures.

ATC-60
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Operational Check (Rear)EJS003XM
The purpose of the operational check is to confirm that the system operates properly.
CHECKING BLOWER
1. Turn the rear blower control dial to switch position "1". Blower should operate on low speed.
2. Turn the rear blower control dial counterclockwise to switch position "2", "3", and "4" until all speeds are
checked.
3. Leave blower on MAX speed.
If NG, go to trouble diagnosis procedure for ATC-101, "
Rear Blower Motor Circuit" .
If OK, continue the check.
CHECKING TEMPERATURE DECREASE
1. Rotate temperature and mode dial fully counterclockwise.
2. Check for cold air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation if OK, go to trouble diagnosis procedure for ATC-121,
"Insufficient Cooling" . If air mix door motor appears to be malfunctioning, go to AT C - 7 9 , "DIAGNOSTIC PRO-
CEDURE FOR AIR MIX DOOR MOTOR (REAR)" .
If OK, continue the check.
CHECKING TEMPERATURE INCREASE
1. Rotate temperature and mode dial clockwise.
2. Check for hot air at appropriate discharge air outlets.
If NG, listen for sound of air mix door motor operation. If OK, go to trouble diagnosis procedure for ATC-128,
"Insufficient Heating" . If air mix door motor appears to be malfunctioning, go to AT C - 7 9 , "DIAGNOSTIC PRO-
CEDURE FOR AIR MIX DOOR MOTOR (REAR)" .
If OK, continue the check. Conditions : Engine running and at normal operating temperature

HEATER & COOLING UNIT ASSEMBLYATC-155
C
DE
F
G H
I
K L
M A
B
AT C
Revision: November 2009 2006 QX56
4. Drain the coolant from the engine cooling system. Refer to MA-13, "DRAINING ENGINE COOLANT" .
5. Disconnect the front heater hoses from the front heater core.
6. Disconnect the high/low pressure pipes from the front expansion valve.
7. Remove the instrument panel and console panel. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
8. Remove the steering column. Refer to PS-10, "
STEERING COLUMN" .
9. Disconnect the instrument panel wire harness at the RH and LH in-line connector brackets, and the fuse block (J/B) electrical connectors. Refer to PG-4, "
POWER SUPPLY ROUTING CIRCUIT" .
10. Disconnect the steering member from each side of the vehicle body.
11. Remove the front heater and cooling unit assembly with it attached to the steering member, from the vehi- cle.
CAUTION:
Use care not to damage the seats and interior trim panels when removing the front heater and
cooling unit assembly with it attached to the steering member.
12. Remove the front heater and cooling unit assembly from the steering member.
Installation
Installation is in the reverse order of removal.
CAUTION:

Replace the O-ring of the low-pressure pipe and high-pressure pipe with a new one, and apply
compressor oil to it when installing it.

After charging the refrigerant, check for leaks.
NOTE:

Fill the engine cooling system with the specified coolant mixture. Refer to MA-14, "REFILLING ENGINE
COOLANT" .

Recharge the A/C system. Refer to ATC-171, "Evacuating System and Charging Refrigerant" .
REAR HEATER AND COOLING UNIT ASSEMBLY
Removal
1. Discharge the refrigerant from the A/C system. Refer to ATC-171, "Discharging Refrigerant" .
2. Drain the coolant from the engine cooling system. Refer to MA-13, "
DRAINING ENGINE COOLANT" .
3. Disconnect the rear heater core hoses from the rear heater core.
4. Disconnect the rear A/C pipes from the rear expansion valve.
5. Remove the luggage side finisher lower RH. Refer to EI-35,
"BODY SIDE TRIM" .
6. Disconnect the following electrical connectors:

Rear blower motor

Rear blower motor resistor

Rear air mix door motor
7. Disconnect the ducts from the rear heater and cooling unit assembly.
8. Remove the rear heater and cooling unit assembly.
Installation
Installation is in the reverse order of removal.
CAUTION:

Replace the O-ring of the low-pressure pipe and high-pressure pipe with a new one, and apply
compressor oil to it when installing it.

After charging the refrigerant, check for leaks.
NOTE:

Fill the engine cooling system with the specified coolant mixture. Refer to MA-14, "REFILLING ENGINE
COOLANT" .

Recharge the A/C system. Refer to ATC-171, "Evacuating System and Charging Refrigerant" .
LJIA0021E

AUDIOAV-7
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
1. Fuse block (J/B)2. Fuse and fusible link box 3. Front tweeter LH
M109
4. Combination meter M24 5. Center speaker
M110 6. Display unit
M93
7. Display control unit M94, M95 8. Front tweeter RH
M 111 9. AV Switch
M98
10. Audio unit M43, M44, M45, M46 11. BOSE speaker amp
M112, M113 12. Satellite radio tuner (pre-wiring or factory
installed, if equipped)
M41
13. Steering wheel audio control switches 14. Front door speaker LH, RH D12, D11215. Rear door tweeter LH, RH
D208, D308
16. Rear door speaker LH, RH D207, D307 17. Driver seat
18. Subwoofer
B72
19. Rear audio remote control unit R204

AV-8
AUDIO
Revision: November 20092006 QX56
System DescriptionEKS00BI8
Refer to Owner's Manual for audio system operating instructions.
Power is supplied at all times

through 15A fuse [No. 17, located in the fuse block (J/B)]

to subwoofer terminal 6

through 20A fuse [No. 31, located in the fuse and fusible link box]

to audio unit terminal 6

to BOSE speaker amp. terminal 1

to AV switch terminal 1 and

to display control unit terminal 1.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 4, located in the fuse block (J/B)]

to audio unit terminal 10 and

to AV switch terminal 2 and

to display control unit terminal 10.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 12, located in the fuse block (J/B)]

to display control unit terminal 12.
Ground is supplied through the case of the audio unit.
Ground is also supplied

to subwoofer terminal 5

through body grounds B7 and B19 and

to BOSE speaker amp. terminal 17

to AV switch terminal 5 and

to display unit terminal 1 and

to display control unit terminal 3

through body grounds M57, M61 and M79.
Then audio signals are supplied

through audio unit terminals 1, 2, 3, 4, 13, 14, 15 and 16

to BOSE speaker amp. terminals 23, 24, 25, 26, 27, 28, 29 and 30.
Audio signals are amplified by the BOSE speaker amp.
The amplified audio signals are supplied

through BOSE speaker amp. terminals 2, 3, 9,10,11,12, 13, 14, 15, 16, 18 and 19

to terminals + and - of front door speaker LH and RH and

to terminals + and - of front tweeter LH and RH and

to terminals + and - of center speaker and

to terminals + and - of rear door speaker LH and RH and

to terminals + and - of rear door tweeter LH and RH and

to terminals 1 and 2 of subwoofer.
When one of steering wheel audio control switches is pushed, the resistance in steering switch circuit changes
depending on which button is pushed.
REAR AUDIO REMOTE CONTROL UNIT
Power is supplied

from audio unit terminal 32

to rear audio remote control unit terminal 13.
Ground is supplied

to rear audio remote control unit terminal 15

through body grounds B117 and B132.
Audio signals are supplied

BCM (BODY CONTROL MODULE)BCS-7
C
DE
F
G H
I
J
L
M A
B
BCS
Revision: November 2009 2006 QX56

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state:
–Ignition switch
–Key switch (insert)
–Hazard switch
–Main door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back latch (door ajar switch)
–Glass hatch ajar switch
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Front door lock assembly LH (key cylinder switch)

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY

Power door lock system. Refer to BL-16, "POWER DOOR LOCK SYSTEM" .

Remote keyless entry system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Power window system. Refer to GW-15, "POWER WINDOW SYSTEM" . NOTE

Sunroof system. Refer to RF-10, "SUNROOF" . NOTE

Room lamp timer. Refer to LT- 1 3 4 , "INTERIOR ROOM LAMP" .

Warning chime system. Refer to DI-43, "WARNING CHIME" .

Turn signal and hazard warning lamps system. Refer to LT- 8 0 , "TURN SIGNAL AND HAZARD WARNING
LAMPS" .

Trailer turn signal and hazard warning lamps system (if equipped). Refer to LT- 1 2 6 , "TRAILER TOW" .

Rear wiper and washer system. Refer to WW-32, "REAR WIPER AND WASHER SYSTEM" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R

Panic system. Refer to BL-44, "REMOTE KEYLESS ENTRY SYSTEM" .

Vehicle security system. Refer to BL-75, "VEHICLE SECURITY (THEFT WARNING) SYSTEM" .

IVIS (NATS) system. Refer to BL-137, "IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .

Headlamp, tail lamp, front fog lamp, auto light and battery saver control systems. Refer to LT- 5 , "HEAD-
LAMP (FOR USA)" , LT- 3 3 , "HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -" , LT- 111 ,
"PARKING, LICENSE PLATE AND TAIL LAMPS" , LT- 6 9 , "FRONT FOG LAMP" or LT- 4 7 , "AUTO LIGHT
SYSTEM" .

Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .

Rear window defogger system. Refer to GW-74, "REAR WINDOW DEFOGGER" .
MAJOR COMPONENTS AND CONTROL SYSTEM
System InputOutput
Remote keyless entry system Remote keyless entry receiver (keyfob)

All door locking actuators

Back door opener actuator

Turn signal lamps
Power door lock system

Front power door lock/unlock switch (LH, RH)

All door switches

Key switch All door locking actuators

BCS-8
BCM (BODY CONTROL MODULE)
Revision: November 20092006 QX56
CAN Communication System DescriptionEKS00D7X
Refer to LAN-26, "CAN COMMUNICATION" .
Power supply [ignition (IGN)/retained
accessory power (RAP)] to power win-
dow and sunroof IGN/RAP supply
Power supply to power window and
sunroof system
Power supply (BAT) to power window
and sunroof Battery power supply Power supply to power window and
sunroof system
Panic alarm

Key switch

Remote keyless entry receiver (keyfob) IPDM E/R
Auto light system

Optical sensor

Combination switch IPDM E/R
Battery saver control

Ignition switch

Combination switch

Front door switch LH and RH IPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

Remote keyless entry receiver (keyfob)

Main power window and door lock/unlock switch

Front door lock assembly LH (key cylinder switch)

All door switches Interior room lamp
Key warning chime

Key switch

Front door switch LH Combination meter (warning
buzzer)
Light warning chime

Combination switch

Key switch

Front door switch LH Combination meter (warning
buzzer)
Vehicle-speed-sensing intermittent
wiper

Combination switch

Combination meter IPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Air conditioner switch signal Front air control ECM
Blower fan switch signal Front air control ECM
Low tire pressure warning system Remote keyless entry receiver

Combination meter

Display control unit
Trailer tow (if equipped) Combination switch Trailer turn signal relays
Vehicle security system

Remote keyless entry receiver (keyfob)

Main power window and door lock/unlock switch

Power window and door lock/unlock switch RH

Front door lock assembly LH (key cylinder switch)

All door switches

Back door latch (door ajar switch)

IPDM E/R

Security indicator lamp
System
InputOutput