Seat INFINITI QX56 2008 Factory Repair Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2008, Model line: QX56, Model: INFINITI QX56 2008Pages: 4083, PDF Size: 81.73 MB
Page 98 of 4083
ADP-84
< COMPONENT DIAGNOSIS >
MIRROR SENSOR
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir-
ror LH connector.
3. Check continuity between automatic drive positioner control unit harness connector and door mirror LH harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR LH SENSOR CIRCUIT 2
1. Check continuity between automatic drive positioner control unit harness connector and door mirror LH harness connector.
2. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4. CHECK PEDAL ADJUSTING OPERATION
1. Connect driver seat control unit connector and door mirror LH connector.
2. Turn ignition switch ON.
3. Check pedal adjusting operation with memory function.
Is the operation normal?
YES >> Replace door mirror actuator LH. Refer to MIR-11, "Door Mirror Assembly".
NO >> Replace automatic drive positioner control unit.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning part.
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M33 6
D4 7
Ye s
22 8
Automatic drive positioner control unit connector Te r m i n a l
Ground Continuity
M33 6
No
22
LIIA1484E
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M34 33
D4 5
Ye s
41 6
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M34 33
No
41
LIIA1483E
Revision: March 2010 2008 QX56
Page 100 of 4083
ADP-86
< COMPONENT DIAGNOSIS >
MIRROR SENSOR
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir-
ror RH.
3. Check continuity between automatic drive positioner control unit harness connector and door mirror RH harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3.CHECK DOOR MIRROR RH SENSOR POWER SUPPLY CIRCUIT
1. Check continuity between automatic drive positioner control unit harness connector and door mirror RH harness connector.
2. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4.CHECK PEDAL ADJUSTING OPERATION
1. Connect driver seat control unit connector and door mirror RH connector.
2. Turn ignition switch ON.
3. Check pedal adjusting operation with memory function.
Is the operation normal?
YES >> Replace door mirror actuator RH. Refer to MIR-11, "Door Mirror Assembly".
NO >> Replace automatic drive positioner control unit.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning part.
Automatic drive posi- tioner control unit connector Terminal
Door mirror RH
connector Terminal Continuity
M33 5
D107 7
Ye s
21 8
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M33 5
No
21
LIIA1473E
Automatic drive posi-
tioner control unit connector Te r m i n a l
Door mirror RH
connector Terminal Continuity
M34 33
D107 5
Ye s
41 6
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M34 33
No
41
LIIA1486E
Revision: March 2010 2008 QX56
Page 101 of 4083
SLIDING MOTORADP-87
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SLIDING MOTOR
DescriptionINFOID:0000000001735528
• The sliding motor LH is installed to the seat cushion frame.
• The sliding motor LH is installed with the driver seat control unit.
• The seat is slid forward/backward by changing the rotation direction of sliding motor LH.
Component Function CheckINFOID:0000000001735529
1. CHECK FUNCTION
1. Select “SEAT SLIDE” in “Active test” mode with CONSULT-III.
2. Check the sliding motor LH operation.
Is the operation of relevant parts normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-87, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735530
1. CHECK SLIDING MOTOR LH POWER SUPPLY
1. Turn the ignition switch ACC.
2. Perform “Active test” (“SEA T SLIDE”) with CONSULT-lll
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> Replace sliding motor LH. (Built in seat slide cushion frame.)
NO >> GO TO 2
2. CHECK SLIDING MOTOR LH CIRCUIT
Test Item Description
SEAT SLIDE OFF
Seat sliding Stop
FR Forward
RR Backward
Te r m i n a l
Test ItemVoltage (V)
(Approx.)
(+)
(-)
Driver seat
control unit connector Te r m i n a l
B203 35
Ground SEAT
SLIDE OFF
0
FR (forward) Battery voltage
RR (backward) 0
42 OFF
0
FR (forward) 0
RR (backward) Battery voltage
PIIA4801E
Revision: March 2010 2008 QX56
Page 102 of 4083
ADP-88
< COMPONENT DIAGNOSIS >
SLIDING MOTOR
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and sliding motor LH.
3. Check continuity between driver seat control unit harness con-nector and sliding motor LH harness connector.
4. Check continuity between driver seat control unit harness con- nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Driver seat control unit connector Te r m i n a lSliding motor LH
connector Terminal Continuity
B203 35
B204 6
Ye s
42 4
Driver seat control unit connector Te r m i n a l
GroundContinuity
B203 35
No
42
LIIA0696E
Revision: March 2010 2008 QX56
Page 103 of 4083
RECLINING MOTORADP-89
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
RECLINING MOTOR
DescriptionINFOID:0000000001735531
• The reclining motor LH is installed to the seat back frame.
• The reclining motor LH is activated with the driver seat control unit.
• The seatback is reclined forward/backward by changing the rotation direction of reclining motor LH.
Component Function CheckINFOID:0000000001735532
1. CHECK FUNCTION
1. Select “SEAT RECLINING” in “Active test” mode with CONSULT-III.
2. Check the reclining motor LH operation.
Is the operation of relevant parts normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-89, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735533
1. CHECK RECLINING MOTOR LH POWER SUPPLY
1. Turn the ignition switch ACC.
2. Perform “Active test” (“SEAT RECLINING”) with CONSULT-lll
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> Replace reclining motor LH. (Built in seat back frame.)
NO >> GO TO 2
2. CHECK RECLINING MOTOR LH CIRCUIT
Test Item Description
SEAT RECLINING OFF
Seat reclining St op
FR Forward
RR Backward
Te r m i n a l
Test ItemVoltage (V)
(Approx.)
(+)
(-)
Driver
seat con- trol unit
connector Te r m i n a l
B203 36
Ground SEAT RE-
CLINING OFF 0
FR (forward) Battery voltage
RR (backward) 0
44 OFF 0
FR (forward) 0
RR (backward) Battery voltage
PIIA4802E
Revision: March 2010
2008 QX56
Page 104 of 4083
ADP-90
< COMPONENT DIAGNOSIS >
RECLINING MOTOR
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector and recling motorLH.
3. Check continuity between driver seat control unit harness con- nector and reclining motor harness connector.
4. Check continuity between driver seat control unit harness con- nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Driver seat control unit connector Te r m i n a lReclining motor LH
connector Terminal Continuity
B203 36
B205 4
Ye s
44 3
Driver seat control unit connector Te r m i n a l
Ground Continuity
B203 36
No
44
LIIA0697E
Revision: March 2010 2008 QX56
Page 105 of 4083
LIFTING MOTOR (FRONT)ADP-91
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
LIFTING MOTOR (FRONT)
DescriptionINFOID:0000000001735534
• The lifting motor (front) is installed to the seat slide cushion frame.
• The lifting motor (front) is activat ed with the driver seat control unit.
• The lifter (front) is moved upward/downward by changi ng the rotation direction of lifting motor (front).
Component Function CheckINFOID:0000000001735535
1. CHECK FUNCTION
1. Select “SEAT LIFTER FR” in “A ctive test” mode with CONSULT-III.
2. Check the lifting motor (front) operation.
Is the operation of relevant parts normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-91, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735536
1. CHECK LIFTING MOTOR (FRONT) POWER SUPPLY
1. Turn the ignition switch ACC.
2. Perform “Active test” (“SEAT LIFTER FR”) with CONSULT-lll.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> Replace lifting motor (front). (Built in seat slide cushion frame.)
NO >> GO TO 2
2. CHECK LIFTING MOTOR (FRONT) CIRCUIT
Test Item Description
SEAT LIFTER FR OFF
Seat lifting (front) St op
UP Upward
DWN Downward
Te r m i n a l
Te s t I t e mVoltage (V)
(Approx.)
(+)
(-)
Driver seat
control unit connector Te r m i n a l
B203 37
Ground SEAT
LIFTER
FR OFF
0
UP 0
DWN (down) Battery voltage
45 OFF
0
UP Battery voltage
DWN (down) 0
PIIA4805E
Revision: March 2010 2008 QX56
Page 106 of 4083
ADP-92
< COMPONENT DIAGNOSIS >
LIFTING MOTOR (FRONT)
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and lifting motor (front) con-nectors.
3. Check continuity between driver seat control unit harness con- nector and lifting motor (front) harness connector.
4. Check continuity between driver seat control unit harness con- nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Driver seat control unit connector Te r m i n a lLifting motor (front)
connector Terminal Continuity
B203 37
B206 6
Ye s
45 4
Driver seat control unit connector Terminal
GroundContinuity
B203 37
No
45
LIIA0698E
Revision: March 2010 2008 QX56
Page 107 of 4083
LIFTING MOTOR (REAR)ADP-93
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
LIFTING MOTOR (REAR)
DescriptionINFOID:0000000001735537
• The lifting motor (rear) is installed to the seat slide cushion frame.
• The lifting motor (rear) is activated with the driver seat control unit.
• The seat lifter (rear) is moved upward/downward by c hanging the rotation direction of lifting motor (rear).
Component Function CheckINFOID:0000000001735538
1. CHECK FUNCTION
1. Select “SEAT LIFTER RR” in “Act ive test” mode with CONSULT-III.
2. Check the lifting motor (rear) operation.
Is the operation of relevant parts normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-93, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735539
1. CHECK LIFTING MOTOR (REAR) POWER SUPPLY
1. Turn the ignition switch OFF.
2. Perform “Active test” (“SEAT LIFTER RR”) with CONSULT-lll
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> Replace lifting motor (rear). (Built in seat slide cushion frame.)
NO >> GO TO 2
2. CHECK LIFTING MOTOR (REAR) CIRCUIT
Test Item Description
SEAT LIFTER RR OFF
Seat lifting (rear) Stop
UP Upward
DWN Downward
Te r m i n a l
Test ItemVoltage (V)
(Approx.)
(+)
(-)
Driver seat
control unit connector Te r m i n a l
B203 38
Ground SEAT
LIFTER
RROFF
0
UP Battery voltage
DWN (down) 0
39 OFF
0
UP 0
DWN (down) Battery voltage
PIIA4804E
Revision: March 2010 2008 QX56
Page 108 of 4083
ADP-94
< COMPONENT DIAGNOSIS >
LIFTING MOTOR (REAR)
1. Disconnect driver seat control unit connector and lifting motor(rear).
2. Check continuity between driver seat control unit harness con-
nector and lifting motor (rear) harness connector.
3. Check continuity between driver seat control unit harness con- nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Driver seat control unit connector Te r m i n a lLifting motor (rear)
connector Terminal Continuity
B203 38
B207 6
Ye s
39 4
Driver seat control unit connector Te r m i n a l
GroundContinuity
B203 38
No
39
LIIA0699E
Revision: March 2010 2008 QX56