Seat INFINITI QX56 2008 Factory Manual PDF

ADP-102
< COMPONENT DIAGNOSIS >
SEAT MEMORY INDICATOR LAMP
SEAT MEMORY INDICATOR LAMP
DescriptionINFOID:0000000001735547
• Memory switch is equipped on the seat memory switch installed to the driver side door trim. The operation
signal is inputted to the automatic drive positioner control unit when the memory switch is operated.
• The status of automatic drive positioner system can be checked according to the illuminating/flashing status.
Component Function CheckINFOID:0000000001735548
1. CHECK FUNCTION
1. Select “MEMORY SW INDCTR” in “A ctive test” mode with CONSULT-III.
2. Check the memory indicator operation.
Is the operation of relevant parts normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-102, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735549
1. CHECK SEAT MEMORY INDICATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and seat memory switch.
3. Check continuity between automatic drive positioner control unit harness connector and seat memory switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK MEMORY INDICATOR POWER SUPPLY
Test item Description
MEMORY SW INDCTR OFF
Memory switch indicator OFF
ON-1 Indicator 1: ON
ON-2 Indicator 2: ON
Automatic drive
positioner control
unit connector Te r m i n a l
Seat memory switch
connector Terminal Continuity
M33 12
D5 6
Ye s
13 7
Automatic drive position- er connector Te r m i n a l
GroundContinuity
M33 12
No
13
LIIA1022E
Revision: March 2010 2008 QX56

SEAT MEMORY INDICATOR LAMPADP-103
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Check voltage between seat memory switch harness connector and
ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Check the following. •Fuse
• Harness for open or short between memory indicator and fuse.
3. CHECK MEMORY INDICATOR
Refer to ADP-103, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace seat memory switch.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic driv e positioner control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735550
1. CHECK SEAT MEMORY INDICATOR
1. Disconnect seat memory switch.
2. Check continuity between seat memory switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace seat memory switch.
Seat memory switch connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
D5 5Ground Battery voltage
PIIA4595E
Te r m i n a l
Continuity
Seat memory switch
(+) (-)
6 5Y es
7
ALJIA0200ZZ
Revision: March 2010 2008 QX56

ADP-104
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
ECU DIAGNOSIS
DRIVER SEAT CONTROL UNIT
Reference ValueINFOID:0000000001735551
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III MONITOR ITEM
Monitor ItemCondition Value/Status
SET SW Set switch Push
ON
Release OFF
MEMORY SW1 Memory switch 1 Push
ON
Release OFF
MEMORY SW2 Memory switch 2 Push
ON
Release OFF
SLIDE SW–FR Sliding switch (front) Operate
ON
Release OFF
SLIDE SW–RR Sliding switch (rear) Operate
ON
Release OFF
RECLN SW–FR Reclining switch (front) Operate
ON
Release OFF
RECLN SW–RR Reclining switch (rear) Operate
ON
Release OFF
LIFT FR SW–UP Lifting switch front (up) Operate
ON
Release OFF
LIFT FR SW–DN Lifting switch front (down) Operate
ON
Release OFF
LIFT RR SW–UP Lifting switch rear (up) Operate
ON
Release OFF
LIFT RR SW–DN Lifting switch rear (down) Operate
ON
Release OFF
MIR CON SW–UP Mirror switch Up
ON
Other than above OFF
MIR CON SW–DN Mirror switch Down
ON
Other than above OFF
MIR CON SW–RH Mirror switch Right
ON
Other than above OFF
MIR CON SW–LH Mirror switch Left
ON
Other than above OFF
MIR CHNG SW–R Chan geover switchRight
ON
Other than above OFF
MIR CHNG SW–L Chan geover switchLeft
ON
Other than above OFF
PEDAL SW-FR Pedal adjusting switch Forward
ON
Other than above OFF
PEDAL SW-RR Pedal adjusting switch Backward
ON
Other than above OFF
Revision: March 2010 2008 QX56

DRIVER SEAT CONTROL UNITADP-105
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
TERMINAL LAYOUT
PHYSICAL VALUES
DETENT SW AT selector lever P position
OFF
Other than above ON
STARTER SW Ignition position Cranking
ON
Other than above OFF
SLIDE PULSE Seat sliding Forward
The numeral value decreases
Backward The numeral value increases
Other than above No change to numeral value
RECLN PULSE Seat reclining Forward
The numeral value decreases
Backward The numeral value increases
Other than above No change to numeral value
LIFT FR PULSE Seat lifter (front) Up
The numeral value decreases
Down The numeral value increases
Other than above No change to numeral value
LIFT RR PULSE Seat lifter (rear) Up
The numeral value decreases
Down The numeral value increases
Other than above No change to numeral value
MIR/SEN RH U–D Door mirror (passenger side) Close to peak
3.4
Close to valley 0.6
MIR/SEN RH R–L Door mirror (passenger side) Close to left edge
3.4
Close to right edge 0.6
MIR/SEN LH U–D Door mirror (driver side) Close to peak
3.4
Close to valley 0.6
MIR/SEN LH R–L Door mirror (driver side) Close to left edge
0.6
Close to right edge 3.4
PEDAL SEN Pedal position Forward
0.5
Backward 4.5
Monitor Item
Condition Value/Status
LIIA2449E
Revision: March 2010 2008 QX56

ADP-106
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
Te r m i n a lWire
Color Item
Condition Voltage (V)
(Approx.)
1 L UART LINE (RX) Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
3 L CAN-H ——
6 O Ignition switch (START) Ignition switch (START position) Battery voltage
9 L/R Reclining motor sensor signal ON (seat reclining motor opera-
tion)
Other than above
0 or 5
10 W Rear lifting motor sensor signal ON (rear lifting motor operation)
Other than above
0 or 5
11 R / B Sliding switch BACKWARD sig-
nal ON (seat sliding switch BACK-
WARD operation)
0
Other than above Battery voltage
12 O/B Reclining switch BACKWARD
signal ON (seat reclining switch BACK-
WARD operation)
0
Other than above Battery voltage
13 L/B Front lifting switch DOWN signal ON (front lifting switch DOWN op-
eration)
0
Other than above Battery voltage
14 G/W Rear lifting switch DOWN signal ON (rear lifting switch DOWN op-
eration)
0
Other than above Battery voltage
15 L/Y Pedal adjustin
g switch BACK-
WARD signal ON (pedal adjusting switch BACK-
WARD operation)
0
Other than above Battery voltage
16 W Seat sensor power Ignition switch ON 5
17 W UART LINE (TX) Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
PIIA4813E
SIIA0692J
SIIA0693J
PIIA4814E
Revision: March 2010
2008 QX56

DRIVER SEAT CONTROL UNITADP-107
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
19 P CAN-L ——
21 L/R A/T shift selector (park position
switch) signal A/T selector lever in P position
0
A/T selector lever in other than P
position with ignition key in ignition
cylinder Battery voltage
24 Y/G Seat sliding motor sensor signal ON (seat sliding motor operation)
Other than above
0 or 5
25 LG Front lifting motor sensor signal ON (front lifting motor operation)
Other than above.
0 or 5
26 P/B Seat sliding switch FORWARD
signal ON (seat sliding switch FOR-
WARD operation)
0
Other than above Battery voltage
27 G/B Seat reclining switch FORWARD
signal ON (seat reclining switch FOR-
WARD operation)
0
Other than above Battery voltage
28 Y/B Front lifting switch UP signal ON (front lifting switch UP opera-
tion)
0
Other than above Battery voltage
29 R/W Rear lifting switch UP signal ON (rear lifting switch UP opera-
tion)
0
Other than above Battery voltage
30 R Pedal adjusting switch FOR-
WARD signal ON (pedal adjusting switch FOR-
WARD operation)
0
Other than above Battery voltage
31 L/Y Sensor ground —0
32 B Ground —0
33 L/B Battery power supply —Battery voltage
35 V/W Sliding motor FORWARD output
signal Sliding switch FORWARD opera-
tion (Motor operated)
Battery voltage
Other than above 0
36 Y/G Reclining motor FORWARD out-
put signal Reclining switch FORWARD oper-
ation (Motor operated)
Battery voltage
Other than above 0
37 BR Front lifting motor DOWN output
signal Front lifting switch DOWN opera-
tion (Motor operated)
Battery voltage
Other than above 0
Te r m i n a l
Wire
Color Item
Condition Voltage (V)
(Approx.)
PIIA3277E
SIIA0691J
Revision: March 2010 2008 QX56

ADP-108
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
38 B/WRear lifting motor UP output sig-
nal Rear end lifting switch UP opera-
tion (Motor operated)
Battery voltage
Other than above 0
39 Y Rear lifting motor DOWN output
signal Rear end lifting switch DOWN op-
eration (Motor operated)
Battery voltage
Other than above 0
40 Y/R Battery power supply —Battery voltage
42 O/B Sliding motor BACKWARD out-
put signal Sliding switch BACKWARD opera-
tion (Motor operated)
Battery voltage
Other than above 0
44 Y/R Reclining motor BACKWARD
output signal Reclining switch BACKWARD op-
eration (Motor operated)
Battery voltage
Other than above 0
45 GR Front lifting motor UP output sig-
nal Front lifting switch UP operation
(Motor operated)
Battery voltage
Other than above 0
48 B/W Ground — 0
Te r m i n a l
Wire
Color Item
Condition Voltage (V)
(Approx.)
Revision: March 2010 2008 QX56

DRIVER SEAT CONTROL UNITADP-109
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Wiring DiagramINFOID:0000000001735552
AAJWA0025GB
Revision: March 2010 2008 QX56

ADP-110
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
AAJWA0026GB
Revision: March 20102008 QX56

DRIVER SEAT CONTROL UNITADP-111
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
AAJWA0027GB
Revision: March 2010 2008 QX56