Seat INFINITI QX56 2008 Factory Workshop Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2008, Model line: QX56, Model: INFINITI QX56 2008Pages: 4083, PDF Size: 81.73 MB
Page 63 of 4083

RECLINING SWITCHADP-49
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit connector.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK RECLINING SWITCH
Refer to ADP-49, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735474
1. CHECK RECLINING SWITCH
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 12
No
27
Driver seat control
unit connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 12
Ground Battery voltage
27
PIIA4580E
Te r m i n a l s Condition Continuity
Power seat switch LH
3 9
Reclining switch
(backward) Operate
Yes
Release No
10 Reclining switch
(forward) Operate
Yes
Release No
LIIA1128E
Revision: March 2010 2008 QX56
Page 64 of 4083

ADP-50
< COMPONENT DIAGNOSIS >
LIFTING SWITCH (FRONT)
LIFTING SWITCH (FRONT)
DescriptionINFOID:0000000001735475
Lifting switch (front) is equipped to the power seat switch LH on the seat cushion side surface. The operation
signal is input to the driver seat control unit when the lifting switch (front) is operated.
Component Function CheckINFOID:0000000001735476
1. CHECK FUNCTION
1. Select “LIFT FR SW-UP”, “LIFT FR SW-DN” in “DATA MONITOR” mode with CONSULT-III.
2. Check lifting switch (front) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-50, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735477
1. CHECK LIFTING SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK LIFTING SW ITCH (FRONT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and power seat switch LH.
3. Check continuity between driver seat control unit harness con- nector and power seat switch LH harness connector.
Monitor item ConditionStatus
LIFT FR SW-UP Lifting switch front (up) Operate
ON
Release OFF
LIFT FR SW-DN Lifting switch front (down) Operate
ON
Release OFF
Driver seat
control unit
connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
B202 13
Ground Lifting
switch (front) Operate
(down) 0V
Release Battery
voltage
28 Operate (up) 0V
Release Battery
voltage
PIIA4583E
Driver seat control unit connector Te r m i n a lPower seat switch
LH connector Terminal Continuity
B202 13
B208 5
Ye s
28 6
LIIA1129E
Revision: March 2010 2008 QX56
Page 65 of 4083

LIFTING SWITCH (FRONT)ADP-51
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK LIFTING SWITCH (FRONT)
Refer to ADP-51, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735478
1. CHECK LIFTING SWITCH (FRONT)
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Terminal
GroundContinuity
B202 13
No
28
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 13
Ground Battery voltage
28
PIIA4583E
Te r m i n a l Condition Continuity
Power seat switch LH
3 5 Lifting switch front (down)
Operate
Yes
Release No
6 Lifting switch front (up) Operate
Yes
Release No
LIIA1130E
Revision: March 2010 2008 QX56
Page 66 of 4083

ADP-52
< COMPONENT DIAGNOSIS >
LIFTING SWITCH (REAR)
LIFTING SWITCH (REAR)
DescriptionINFOID:0000000001735479
Lifting switch (rear) is equipped to the power seat switch LH on the seat cushion side surface. The operation
signal is inputted to the driver seat control unit when the lifting switch (rear) is operated.
Component Function CheckINFOID:0000000001735480
1. CHECK FUNCTION
1. Select “LIFT RR SW-UP”, “LIFT RR SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check lifting switch (rear) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-52, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735481
1. CHECK LIFTING SWITCH (REAR) SIGNAL
1. Turn ignition switch ON.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK LIFTING SW ITCH (REAR) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and power seat switch LH.
3. Check continuity between driver seat control unit harness con- nector and power seat switch LH harness connector.
4. Check continuity between driver seat control unit harness con- nector and ground.
Monitor item ConditionStatus
LIFT RR SW-UP Lifting switch rear (up) Operate
ON
Release OFF
LIFT RR SW-DN Lifting switch rear (down) Operate
ON
Release OFF
Driver seat
control unit
connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
B202 14
Ground Lifting
switch (rear) Operate (down) 0
Release Battery voltage
29 Operate (up) 0
Release Battery voltage
PIIA4586E
Driver seat control unit connector Te r m i n a lPower sear switch
LH connector Terminal Continuity
B202 14
B208 8
Ye s
29 2
LIIA1131E
Revision: March 2010 2008 QX56
Page 67 of 4083

LIFTING SWITCH (REAR)ADP-53
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK LIFTING SWITCH (REAR)
Refer to ADP-53, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735482
1. CHECK LIFTING SWITCH (REAR)
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 14
No
29
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 14
Ground Battery voltage
29
PIIA4586E
Te r m i n a l Condition Continuity
Power seat switch LH
3 2 Lifting switch rear (up)
Operate Yes
Release No
8 Lifting switch rear (down) Operate Yes
Release No
LIIA1132E
Revision: March 2010
2008 QX56
Page 70 of 4083

ADP-56
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
PEDAL ADJUSTING SWITCH
DescriptionINFOID:0000000001735483
Pedal adjusting switch is on the instrument panel. The operation signal is input to the driver seat control unit
when the pedal adjusting switch is operated. The pedal adjus ting switch signal is sent to the automatic drive
positioner control unit via UART communication.
Component Function CheckINFOID:0000000001735484
1. CHECK FUNCTION
1. Select “PEDAL SW-FR”, “PEDAL SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check pedal adjusting switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-56, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735485
1. CHECK PEDAL ADJUSTING SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK PEDAL ADJUSTING SWITCH CIRCUIT
Monitor item ConditionStatus
PEDAL SW-FR Pedal adjusting switch (forward) Operate
ON
Release OFF
PEDAL SW-RR Pedal adjusting switch (backward) Operate
ON
Release OFF
Driver seat
control unit connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
B202 15
Ground Pedal ad-
justing switch Operate
(backward) 0
Release Battery
voltage
30 Operate
(forward) 0
Release Battery
voltage
PIIA4591E
Revision: March 2010 2008 QX56
Page 71 of 4083

PEDAL ADJUSTING SWITCHADP-57
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and pedal adjusting switch.
3. Check continuity between driver seat control unit harness con- nector and pedal adjusting switch harness connector.
4. Check continuity between driver seat control unit harness con- nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK PEDAL ADJUSTING SWITCH
Refer to ADP-58, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace pedal adjusting switch.
5. CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector M96 ter-
minal 1 and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> Replace or replace harness.
6. CHECK INTERMITTENT INCIDENT
Driver seat
control unit
connector Te r m i n a l
Pedal adjusting
switch connector Terminal Continuity
B202 15
M96 2
Ye s
30 3
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 15
No
30
LIIA0726E
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 15
Ground Battery voltage
30
PIIA4591E
1 - Ground : Continuity should exist.
LIIA1015E
Revision: March 2010 2008 QX56
Page 73 of 4083

SEAT MEMORY SWITCHADP-59
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SEAT MEMORY SWITCH
DescriptionINFOID:0000000001735487
Memory switch is equipped on the seat memory switch installed to the front door LH trim. The operation signal
is input to the automatic drive positioner control unit when the memory switch is operated.
Component Function CheckINFOID:0000000001735488
1. CHECK FUNCTION
1. Select “MEMORY SW 1”, “MEMORY SW 2”, "SET SW" in “Data monitor” mode with CONSULT-III.
2. Check seat memory switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-59, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735489
1. CHECK MEMORY SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and seat memory switch.
3. Check continuity between automat ic drive positioner control unit
harness connector and seat memo ry switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK MEMORY SWITCH GROUND CIRCUIT
Monitor item ConditionStatus
MEMORY SW1 Memory switch 1 Push
ON
Release OFF
MEMORY SW2 Memory switch 2 Push
ON
Release OFF
SET SW Set switch Push
ON
Release OFF
Automatic drive
positioner control unit connector Te r m i n a l
Seat memory
switch connector Terminal Continuity
M33 9
D5 1
Ye s
24 3
25 2
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M33 9
No
24
25
PIIA4576E
Revision: March 2010 2008 QX56
Page 74 of 4083

ADP-60
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
Check continuity between seat memory switch harness connector
and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK SEAT MEMORY SWITCH
Refer to ADP-60, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace seat memory switch.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735490
1.CHECK SEAT MEMORY SWITCH
1. Turn ignition switch OFF.
2. Disconnect seat memory switch.
3. Check continuity between seat memory switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace seat memory switch.
Seat memory switch connector Te r m i n a l
GroundContinuity
D5 4 Yes
PIIA4821E
Te r m i n a l
Condition Continuity
Seat memory switch
4 1 Memory switch 1
Push
Yes
Release No
2 Memory switch 2 Push
Yes
Release No
3 Set switch Push
Yes
Release No
LIIA1020E
Revision: March 2010 2008 QX56
Page 80 of 4083

ADP-66
< COMPONENT DIAGNOSIS >
POWER SEAT SWITCH GROUND CIRCUIT
POWER SEAT SWITCH GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000001735499
1. CHECK POWER SEAT SWITCH LH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH connector and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-38, "Intermittent
Incident".
NO >> Repair or replace harness.
Power seat switch LH
connector Te r m i n a l
GroundContinuity
B208 32 Yes
LIIA1133E
Revision: March 2010 2008 QX56