seat memory INFINITI QX56 2009 Factory Owner's Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2009, Model line: QX56, Model: INFINITI QX56 2009Pages: 4171, PDF Size: 84.65 MB
Page 58 of 4171
ADP-44
< COMPONENT DIAGNOSIS >
B2128 UART COMMUNICATION LINE
B2128 UART COMMUNICATION LINE
DescriptionINFOID:0000000003775544
Driver seat control unit performs UART communication with the automatic drive positioner control unit using 2
communication lines, TX and RX line. Driver seat cont rol unit receives the operation signals of pedal adjusting
switch, door mirror remote control switch, set switch and memory switch and the position signals of adjustable
pedal sensor and door mirror sensor from the automatic drive positioner control unit and transmits the opera-
tion request signal.
DTC LogicINFOID:0000000003775545
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Operate pedal adjusting switch for more than 2 seconds.
>> GO TO 3
3. PROCEDURE 3
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-44, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000003775546
1. CHECK UART COMMUNICA TION LINE CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect driver seat contro l unit and automatic drive posi-
tioner control unit.
3. Check continuity between driver seat control unit harness con- nector and automatic drive positi oner control unit harness con-
nector.
4. Check continuity between driver seat control unit harness connector and ground.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause B2128 UART COMM The communication between driver seat control unit
and automatic drive positioner control unit is interrupt-
ed for a period of time. UART communication line
(UART communication line is
open or shorted)
Driver seat control unit
Automatic drive positioner control unit
Driver seat control unit connector Te r m i n a lAutomatic drive positioner
control unit connector Terminal Continuity
B202 1
M33 10
Ye s
17 26
PIIA4598E
Revision: December 20092009 QX56
Page 76 of 4171
ADP-62
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
SEAT MEMORY SWITCH
DescriptionINFOID:0000000003775577
The seat memory switch is installed on the front door LH trim. The operation signal is input to the automatic
drive positioner control unit when the memory switch is operated.
Component Function CheckINFOID:0000000003775578
1. CHECK FUNCTION
1. Select “MEMORY SW 1”, “MEMORY SW 2”, "SET SW" in “Data monitor” mode with CONSULT-III.
2. Check seat memory switch signal under the following conditions.
Is the indication normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-62, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775579
1. CHECK MEMORY SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and seat memory switch.
3. Check continuity between automat ic drive positioner control unit
harness connector and seat memory switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK MEMORY SW ITCH GROUND CIRCUIT
Monitor item Condition Status
MEMORY SW1 Memory switch 1 Push ON
Release OFF
MEMORY SW2 Memory switch 2 Push ON
Release OFF
SET SW Set switch Push ON
Release OFF
Automatic drive
positioner control unit connector Te r m i n a l
Seat memory
switch connector Terminal Continuity
M33 9
D5 1
Ye s
24 3
25 2
Automatic drive positioner control unit connector Terminal
GroundContinuity
M33 9
No
24
25
PIIA4576E
Revision: December 20092009 QX56
Page 77 of 4171
SEAT MEMORY SWITCHADP-63
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Check continuity between seat memory switch harness connector
and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK SEAT MEMORY SWITCH
Refer to ADP-63, "Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace seat memory switch. Refer to ADP-167, "Removal and Installation"
.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace automatic drive posit ioner control unit. Refer to ADP-166, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000003775580
1. CHECK SEAT MEMORY SWITCH
1. Turn ignition switch OFF.
2. Disconnect seat memory switch.
3. Check continuity between seat memory switch terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace seat memory switch. Refer to ADP-167, "Removal and Installation"
.
Seat memory switch
connector Te r m i n a l
GroundContinuity
D5 4 Yes
PIIA4821E
Te r m i n a l Condition Continuity
Seat memory switch
4 1 Memory switch 1
Push Yes
Release No
2 Memory switch 2 Push Yes
Release No
3 Set switch Push Yes
Release No
LIIA1020E
Revision: December 20092009 QX56
Page 89 of 4171
SLIDING SENSORADP-75
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Disconnect driver seat control unit and sliding motor LH.
2. Check continuity between driver seat control unit harness con-
nector and sliding motor LH harness connector.
3. Check continuity between driver seat control unit harness con-
nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK SEAT OPERATION
1. Connect driver seat control unit and sliding motor LH.
2. Check seat operation (except slidi ng operation) with memory function.
Is the inspection result normal?
YES >> Replace sliding motor LH. (Built in power seat frame assembly). Refer to SE-68, "Disassembly
and Assembly".
NO >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation"
.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Driver seat control
unit connector Te r m i n a l
Sliding motor
LH connector Terminal Continuity
B202 (A) 16
B204 (B) 3
Ye s
24 4
31 2
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 (A) 16
No
24
31
ALJIA0317ZZ
Revision: December 20092009 QX56
Page 91 of 4171
RECLINING SENSORADP-77
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Disconnect driver seat control unit and reclining motor LH.
2. Check continuity between driver seat control unit harness con-
nector and reclining motor LH harness connector.
3. Check continuity between driver seat control unit harness con-
nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK SEAT OPERATION
1. Connect driver seat control unit and reclining motor LH.
2. Check seat operation (except reclin ing operation) with memory function.
Is the operation normal?
YES >> Replace reclining motor LH. (Built in seatback assembly). Refer to SE-68, "Disassembly and
Assembly".
NO >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation"
.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Driver seat control
unit connector Te r m i n a l
Reclining motor
connector Terminal Continuity
B202 (A) 9
B205 (B) 1
Ye s
31 4
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 (A) 9
No
31
ALJIA0318ZZ
Revision: December 20092009 QX56
Page 93 of 4171
LIFTING SENSOR (FRONT)ADP-79
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Disconnect driver seat control unit and lifting motor (front).
2. Check continuity between driver seat control unit harness con-
nector and lifting motor (front) harness connector.
3. Check continuity between driver seat control unit harness con-
nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK SEAT OPERATION
1. Connect driver seat control unit and lifting motor (front).
2. Check seat operation [except lifting (f ront) operation] with memory function.
Is the operation normal?
YES >> Replace lifting motor (front). (Built in power seat frame assembly). Refer to SE-68, "Disassembly
and Assembly".
NO >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation"
.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Driver seat control
unit connector Te r m i n a lLifting motor
(front) connector Terminal Continuity
B202 (A) 16
B206 (B) 3
Ye s
25 4
31 2
Driver seat control unit connector Te r m i n a l
Ground Continuity
B202 (A) 16
No
25
31
ALJIA0319ZZ
Revision: December 20092009 QX56
Page 95 of 4171
LIFTING SENSOR (REAR)ADP-81
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Disconnect driver seat control unit and lifting motor (rear).
2. Check the continuity between driver seat control unit harness connector and lifting motor (rear) harness connector.
3. Check the continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK SEAT OPERATION
1. Connect driver seat control unit and lifting motor (rear).
2. Check the seat operation [except lifting (rear) operation] with memory function.
Is the operation normal?
YES >> Replace lifting motor (rear). (Built in power seat frame assembly). Refer to SE-68, "Disassembly
and Assembly".
NO >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation"
.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-165, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Driver seat control
unit connector Te r m i n a l
Lifting motor (rear)
connector Terminal Continuity
B202 (A) 10
B207 (B) 4
Ye s
16 3
31 2
Driver seat control unit connector Te r m i n a l
Ground Continuity
B202 (A) 10
No
16
31
ALJIA0320ZZ
Revision: December 20092009 QX56
Page 101 of 4171
MIRROR SENSORADP-87
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir- ror LH.
3. Check continuity between automat ic drive positioner control unit
harness connector and door mirror LH harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR LH SENSOR CIRCUIT 2
1. Check continuity between automat ic drive positioner control unit
harness connector and door mirror LH harness connector.
2. Check continuity between automat ic drive positioner control unit
harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK PEDAL ADJUSTING OPERATION
1. Connect driver seat control unit and door mirror LH.
2. Turn ignition switch ON.
3. Check pedal adjusting operation with memory function.
Is the operation normal?
YES >> Replace door mirror actuator LH. Refer to MIR-14, "Mirror Actuator".
NO >> Replace automatic drive positioner control unit. Refer to ADP-166, "Removal and Installation"
.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace automatic drive posit ioner control unit. Refer to ADP-166, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M33 6
D4 7
Ye s
22 8
Automatic drive positioner control unit connector Te r m i n a l
Ground Continuity
M33 6
No
22
LIIA1484E
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M34 33
D4 5
Ye s
41 6
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M34 33
No
41
LIIA1483E
Revision: December 20092009 QX56
Page 103 of 4171
MIRROR SENSORADP-89
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir- ror RH.
3. Check continuity between automat ic drive positioner control unit
harness connector and door mirror RH harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR RH SENSOR POWER SUPPLY CIRCUIT
1. Check continuity between automat ic drive positioner control unit
harness connector and door mirror RH harness connector.
2. Check continuity between automat ic drive positioner control unit
harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK PEDAL ADJUSTING OPERATION
1. Connect driver seat control unit and door mirror RH.
2. Turn ignition switch ON.
3. Check pedal adjusting operation with memory function.
Is the operation normal?
YES >> Replace door mirror actuator RH. Refer to MIR-14, "Mirror Actuator".
NO >> Replace automatic drive positioner control unit. Refer to ADP-166, "Removal and Installation"
.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace automatic drive posit ioner control unit. Refer to ADP-166, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Automatic drive posi-
tioner control unit connector Te r m i n a l
Door mirror RH
connector Terminal Continuity
M33 5
D107 7
Ye s
21 8
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M33 5
No
21
LIIA1473E
Automatic drive posi-
tioner control unit connector Te r m i n a l
Door mirror RH
connector Terminal Continuity
M34 33
D107 5
Ye s
41 6
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M34 33
No
41
LIIA1486E
Revision: December 20092009 QX56
Page 119 of 4171
SEAT MEMORY INDICATOR LAMPADP-105
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SEAT MEMORY INDICATOR LAMP
DescriptionINFOID:0000000003775643
The seat memory switch is installed on the driver si de door trim. The operation signal is inputted to the auto-
matic drive positioner control unit when the memory switch is operated.
The status of automatic drive positioner system can be checked according to the illuminating/flashing status.
Component Function CheckINFOID:0000000003775644
1. CHECK FUNCTION
1. Select “MEMORY SW INDCTR” in “Active test” mode with CONSULT-III.
2. Check the memory indicator operation.
Is the operation of relevant parts normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-105, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000003775645
1. CHECK SEAT MEMORY INDICATOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and seat memory switch.
3. Check continuity between automat ic drive positioner control unit
harness connector and seat memo ry switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK MEMORY INDICATOR POWER SUPPLY
Test item Description
MEMORY SW INDCTR OFF
Memory switch indicator OFF
ON-1 Indicator 1: ON
ON-2 Indicator 2: ON
Automatic drive
positioner control
unit connector Te r m i n a l
Seat memory switch
connector Terminal Continuity
M33 12
D5 6
Ye s
13 7
Automatic drive position- er connector Te r m i n a l
GroundContinuity
M33 12
No
13
LIIA1022E
Revision: December 20092009 QX56