display INFINITI QX56 2010 Factory Service Manual

C1185 ICC UNITBRC-77
< COMPONENT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1185 ICC UNIT
DescriptionINFOID:0000000005148057
When the force applied to brake pedal exceeds a certain level, the brake assist is activated and generates a
greater braking force than that of a convent ional brake booster, even with light pedal force.
When the ICC preview function identifies the need to apply the sudden brake by sensing the vehicle ahead in
the same lane and the distance and relative speed from it, it applies the brake pre-pressure before driver
depresses the brake pedal and improves brak e response by reducing its free play.
DTC LogicINFOID:0000000005148058
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES >> Proceed to diagnosis procedure. Refer to BRC-77, "Diagnosis Procedure".
NO >> Inspection End
Diagnosis ProcedureINFOID:0000000005148059
Regarding Wiring Diagram information, refer to BRC-92, "Wiring Diagram - BRAKE CONTROL SYSTEM -".
1.SELF-DIAGNOSIS RESULT CHECK
Perform self-diagnosis of ICC unit.
Are self-diagnosis result items displayed?
YES >> After checking and repairing the applicabl e item, perform ICC unit self-diagnosis again.
NO >> GO TO 2
2.CONNECTOR INSPECTION
Disconnect the ABS actuator and electric unit (contro l unit) connector and the ICC unit connector and check
the terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace as necessary.
3.ICC UNIT CIRCUIT INSPECTION
DTC Display item Malfunction detected condition Possible cause
C1185 ABS ACC CU INTERNAL NG ICC cont rol unit internal malfunction.• Harness or connector
•ICC unit
• ABS actuator and electric unit
(control unit)
Self-diagnosis results
ABS ACC CU INTERNAL NG
Revision: April 20092010 QX56

U1000 CAN COMM CIRCUITBRC-79
< COMPONENT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000005148061
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC LogicINFOID:0000000005148062
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000005148063
1.CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect the ABS actuat or and electric unit (control unit) connector, and check
the terminals for deformation, disconnection, looseness, and so on. If there is a malfunction, repair or
replace the terminal.
2. Reconnect connector and perform self-diagnosis. Refer to BRC-23, "
CONSULT-III Function (ABS)".
Is
“CAN COMM CIRCUIT” displayed in self-diagnosis display items?
YES >> Print out the self-diagnostic results, and refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Connector terminal is l oose, damaged, open, or shorted.
DTCDisplay item Malfunction detected condition Possible cause
U1000 CAN COMM CIRCUIT When ABS actuator and electric
unit (control unit) is not
transmitting or receiving CAN communication signal for 2
seconds or more. • CAN communication line
• ABS actuator and electric unit
(control unit)
Revision: April 20092010 QX56

BRC-82
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
ABS WARNING LAMP
ABS WARNING LAMP
DescriptionINFOID:0000000005148069
×
: ON –: OFF
Component Function CheckINFOID:0000000005148070
1.CHECK ABS WARNING LAMP OPERATION
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES >> Inspection End
NO >> Go to diagnosis procedure. Refer to BRC-82, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005148071
1.CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-23, "
CONSULT-III Function
(ABS)".
Is the inspection result normal?
YES >> GO TO 2
NO >> Check items displayed by self-diagnosis.
2.CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to MWI-22, "
Diagnosis Descrip-
tion".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-116, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-100, "
Removal and Installation".
Special Repair RequirementINFOID:0000000005194925
1.ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the st eering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to BRC-8, "
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Description".
>> GO TO 2
2.CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replac ing the ABS actuator and electric unit (control unit).
Refer to BRC-9, "
CALIBRATION OF DECEL G SENSOR : Description".
>> END
Condition ABS warning lamp
Ignition switch OFF –
For 2 seconds after turning ON ignition switch ×
2 seconds later after turning ON ignition switch –
ABS function is malfunctioning. ×
EBD function is malfunctioning. ×
Revision: April 20092010 QX56

BRAKE WARNING LAMPBRC-83
< COMPONENT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
BRAKE WARNING LAMP
DescriptionINFOID:0000000005148072
× : ON –: OFF
NOTE:
• 1: Brake warning lamp will turn on in case of parking brake op eration (when switch is ON) or of brake fluid level switch operation
(when brake fluid is insufficient).
• 2: After starting engine, brake warning lamp is turned off.
Component Function CheckINFOID:0000000005148073
1.BRAKE WARNING LAMP OPERATION CHECK
Check that the lamp illuminates after the ignition switch is turned ON, and turns OFF after the engine is
started.
Is the inspection result normal?
YES >> Inspection End
NO >> Go to diagnosis procedure. Refer to BRC-83, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005148074
1.CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-23, "
CONSULT-III Function
(ABS)".
Is the inspection result normal?
YES >> GO TO 2
NO >> Check items displayed by self-diagnosis.
2.CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to MWI-22, "
Diagnosis Descrip-
tion".
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-116, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-100, "
Removal and Installation".
Special Repair RequirementINFOID:0000000005194926
1.ADJUSTMENT OF STEERING AN GLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the st eering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to BRC-8, "
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Description".
>> GO TO 2
2.CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
Refer to BRC-9, "
CALIBRATION OF DECEL G SENSOR : Description".
>> END
Condition Brake warning lamp (Note 1)
Ignition switch OFF –
Ignition switch ON × (Note 2)
EBD function is malfunctioning. ×
Revision: April 20092010 QX56

BRC-84
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
VDC OFF INDICATOR LAMP
VDC OFF INDICATOR LAMP
DescriptionINFOID:0000000005148075
×
: ON –: OFF
Component Function CheckINFOID:0000000005148076
1.VDC OFF INDICATOR LAMP OPERATION CHECK 1
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES >> GO TO 2
NO >> Go to diagnosis procedure. Refer to BRC-84, "
Diagnosis Procedure".
2.VDC OFF INDICATOR LAMP OPERATION CHECK 2
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES >> Inspection End
NO >> Check VDC OFF switch. Refer to BRC-80, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005148077
1.CHECK VDC OFF SWITCH
Check that the VDC OFF indicator lamp in the combination meter turns ON/OFF correctly when operating the
VDC OFF switch.
Is the inspection result normal?
YES >> GO TO 2
NO >> Check VDC OFF switch. Refer to BRC-80, "
Diagnosis Procedure".
2.CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-23, "
CONSULT-III Function
(ABS)".
Is the inspection result normal?
YES >> GO TO 3
NO >> Check items displayed by self-diagnosis.
3.CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to MWI-22, "
Diagnosis Descrip-
tion".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-116, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-100, "
Removal and Installation".
Condition VDC OFF indicator lamp
Ignition switch OFF –
For 2 seconds after turning ON ignition switch ×
2 seconds later after turning ON ignition switch –
VDC OFF switch turned ON. (VDC function is OFF.) ×
VDC/TCS function is malfunctioning. ×
ABS function is malfunctioning. ×
EBD function is malfunctioning. ×
Revision: April 20092010 QX56

BRC-86
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
SLIP INDICATOR LAMP
SLIP INDICATOR LAMP
DescriptionINFOID:0000000005148078
×
: ON –: OFF
Component Function CheckINFOID:0000000005148079
1.CHECK SLIP INDICATOR LAMP OPERATION
Check that the lamp illuminates for approximately 2 seconds after the ignition switch is turned ON.
Is the inspection result normal?
YES >> Inspection End
NO >> Go to diagnosis procedure. Refer to BRC-86, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005148080
1.CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-23, "
CONSULT-III Function
(ABS)".
Is the inspection result normal?
YES >> GO TO 2
NO >> Check items displayed by self-diagnosis.
2.CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to MWI-22, "
Diagnosis Descrip-
tion".
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-116, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-100, "
Removal and Installation".
Special Repair RequirementINFOID:0000000005194928
1.ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the st eering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to BRC-8, "
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Description".
>> GO TO 2
2.CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replac ing the ABS actuator and electric unit (control unit).
Refer to BRC-9, "
CALIBRATION OF DECEL G SENSOR : Description".
>> END
Condition SLIP indicator lamp
Ignition switch OFF –
For 2 seconds after turning ON ignition switch ×
2 seconds later after turning ON ignition switch –
VDC/TCS function is malfunctioning. ×
ABS function is malfunctioning. ×
EBD function is malfunctioning. ×
Revision: April 20092010 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-87
< ECU DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
ECU DIAGNOSIS
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference ValueINFOID:0000000005148081
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.
CONSULT-III MONITOR ITEM
Monitor item Display content Data monitor
Condition Reference value in
normal operation
FR LH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
FR RH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
RR LH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
RR RH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
DECEL G-SEN Longitudinal acceleration detected by Decel
G-Sensor Vehicle stopped
Approx. 0 G
Vehicle running -1.7 to 1.7 G
FR RH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
FR RH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
FR LH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
FR LH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
Revision: April 20092010 QX56

BRC-88
< ECU DIAGNOSIS >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
RR RH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
RR RH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
RR LH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
RR LH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
EBD WARN LAMP EBD warning lamp
(Note 2) When EBD warning lamp is ON
ON
When EBD warning lamp is OFF OFF
STOP LAMP SW Stop lamp switch signal status When brake pedal is depressed
ON
When brake pedal is released OFF
MOTOR RELAY Motor and motor relay operation When the motor relay and motor are op-
erating
ON
When the motor relay and motor are not
operating OFF
ACTUATOR RLY Actuator relay operation When the actuator relay is operating
ON
When the actuator relay is not operating OFF
ABS WARN LAMP ABS warning lamp
(Note 2) When ABS warning lamp is ON
ON
When ABS warning lamp is OFF OFF
OFF LAMP VDC OFF indicator lamp
(Note 2) When VDC OFF indicator lamp is ON
ON
When VDC OFF indicator lamp is OFF OFF
OFF SW VDC OFF switch ON/OFF VDC OFF switch ON
(When VDC OFF indicator lamp is ON)
ON
VDC OFF switch OFF
(When VDC OFF indicator lamp is OFF) OFF
SLIP LAMP SLIP indicator lamp
(Note 2) When SLIP indicator lamp is ON
ON
When SLIP indicator lamp is OFF OFF
BATTERY VOLT Battery voltage supplied to the ABS actuator
and electric unit (control unit) Ignition switch ON
10 – 16 V
GEAR Gear position determined by TCM 1st gear
2nd gear
3rd gear
4th gear
5th gear 1
2
3
4
5
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
Revision: April 20092010 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-89
< ECU DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLCT LVR POSI A/T selector lever position P position
R position
N position
D positionP
R
N
D
ENGINE SPEED With engine running With engine stopped
0 rpm
Engine running Almost in accor-
dance with tachome-
ter display
YAW RATE SEN Yaw rate detected by yaw rate/side/decel G
sensor When vehicle is stopped
Approx. 0 d/s
When vehicle turning −75 to 75 d/s
R POSI SIG Transmission range switch signal ON/OFF
condition A/T shift position = R position
ON
A/T shift position = other than R position OFF
4WD FAIL REQ
(Note 3) Transfer control unit fail-safe signal When transfer control unit is in fail-safe
mode
ON
When transfer control unit is normal OFF
N POSI SIG Transmission range switch signal ON/OFF
condition A/T shift position = N position
ON
A/T shift position = other than N position OFF
P POSI SIG Transmission range switch signal ON/OFF
condition A/T shift position = P position
ON
A/T shift position = other than P position OFF
CV1 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
CV2 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
SV1 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
SV2 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
2WD/4WD Drive axle 2WD model
2WD
4WD model 4WD
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
Revision: April 20092010 QX56

BRC-90
< ECU DIAGNOSIS >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ACCEL POS SIG Throttle actuator opening/closing is dis-
played (linked with accelerator pedal) Accelerator pedal not depressed (ignition
switch is ON)
0 %
Accelerator pedal depressed (ignition
switch is ON) 0 - 100 %
SIDE G-SENSOR Transverse G detected by side G sensor Vehicle stopped
Approx. 0 m/s
2
Vehicle turning rightNegative value
(m/s2)
Vehicle turning left Positive value
(m/s
2)
STR ANGLE SIG Steering angle detected by steering angle
sensor Straight-ahead
Approx. 0°
Steering wheel turned –720 to 720°
BST OPER SIG Active booster operation Active booster is active
ON
Active booster is inactive OFF
PRESS SENSOR Brake fluid pressure detected by front pres-
sure sensor With ignition switch turned ON and brake
pedal released
Approx. 0 bar
With ignition switch turned ON and brake
pedal depressed –40 to 300 bar
EBD SIGNAL EBD operation EBD is active
ON
EBD is inactive OFF
ABS SIGNAL ABS operation ABS is active
ON
ABS is inactive OFF
TCS SIGNAL TCS operation TCS is active
ON
TCS is inactive OFF
VDC SIGNAL VDC operation VDC is active
ON
VDC is inactive OFF
EBD FAIL SIG EBD fail-safe signal In EBD fail-safe
ON
EBD is normal OFF
ABS FAIL SIG ABS fail-safe signal In ABS fail-safe
ON
ABS is normal OFF
TCS FAIL SIG TCS fail-safe signal In TCS fail-safe
ON
TCS is normal OFF
VDC FAIL SIG VDC fail-safe signal In VDC fail-safe
ON
VDC is normal OFF
CRANKING SIG Crank operation Crank is active
ON
Crank is inactive OFF
FLUID LEV SW Brake fluid level switch signal status When brake fluid level switch ON
ON
When brake fluid level switch OFF OFF
PRESS SEN2 Brake fluid pressure detected by rear pres-
sure sensor With ignition switch turned ON and brake
pedal released
Approx. 0 bar
With ignition switch turned ON and brake
pedal depressed –40 to 300 bar
DELTA S SEN Value detected by delta stroke sensor When brake pedal is depressed
1.05 - 1.80 mm
When brake pedal is released 0.00 mm (+0.6/-0.4)
RELEASE SW NO Active booster signal status When brake pedal is depressed
ON
When brake pedal is released OFF
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
Revision: April 20092010 QX56