relay INFINITI QX56 2010 Factory Owner's Manual

BRC-70
< COMPONENT DIAGNOSIS >[VDC/TCS/ABS]
C1164, C1165, C1166
, C1167 CV/SV SYSTEM
YES >> GO TO 2
NO >> Poor connection of connector term inal. Repair or replace connector.
2.CHECK SOLENOID, VDC SWITCH-OVER VALVE A ND ACTUATOR RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and elec tric unit (control unit) connec-
tor.
3. Check voltage between ABS actuator and electric unit (control unit) connector E125 terminal 32 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace malfunctioning components.
3.CHECK SOLENOID, VDC SWITCH-OVER VALV E AND ACTUATOR RELAY GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control
unit) connector E125 terminals 16, 47 and ground.
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-116, "
Removal and Installation".
NO >> Repair or replace malfunctioning components.
Component InspectionINFOID:0000000005148045
1.CHECK ACTIVE TEST
1. Select each test menu item on “ACTIVE TEST”.
2. On the display, touch “Up”, “ACT UP”, and “ACT KEEP”, and check that the system operates as shown in
the table below.
ABS actuator and electric unit (control unit) —Volt a g e
Connector Terminal
E125 32Ground Battery voltage
AWFIA0018ZZ
ABS actuator and electric unit (control unit)
—Continuity
Connector Terminal
E125 16, 47GroundYes
AWFIA0016ZZ
Operation ABS solenoid valve (ACT)
Up ACT UP ACT KEEP
FR RH ABS SOLENOID (ACT) FR RH IN SOL
OffOff Off
FR RH OUT SOL OffOff Off
CV1 OffOn On
SV1 OffOn* Off
FR LH ABS SOLENOID (ACT) FR LH IN SOL
OffOff Off
FR LH OUT SOL OffOff Off
CV1 OffOn On
SV1 OffOn* Off
RR RH ABS SOLENOID (ACT) RR RH IN SOL
OffOff Off
RR RH OUT SOL OffOff Off
CV2 OffOn On
SV2 OffOn* Off
Revision: April 20092010 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-87
< ECU DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
ECU DIAGNOSIS
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference ValueINFOID:0000000005148081
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.
CONSULT-III MONITOR ITEM
Monitor item Display content Data monitor
Condition Reference value in
normal operation
FR LH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
FR RH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
RR LH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
RR RH SENSOR Wheel speed 0 [km/h (MPH)]
Vehicle stopped
Nearly matches the speed meter display
(± 10% or less) Vehicle running
(Note 1)
DECEL G-SEN Longitudinal acceleration detected by Decel
G-Sensor Vehicle stopped
Approx. 0 G
Vehicle running -1.7 to 1.7 G
FR RH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
FR RH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
FR LH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
FR LH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive
(in fail-safe mode) ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
Revision: April 20092010 QX56

BRC-88
< ECU DIAGNOSIS >[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
RR RH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
RR RH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
RR LH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
RR LH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actua-
tor relay is inactive (in fail-safe mode)
ON
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
EBD WARN LAMP EBD warning lamp
(Note 2) When EBD warning lamp is ON
ON
When EBD warning lamp is OFF OFF
STOP LAMP SW Stop lamp switch signal status When brake pedal is depressed
ON
When brake pedal is released OFF
MOTOR RELAY Motor and motor relay operation When the motor relay and motor are op-
erating
ON
When the motor relay and motor are not
operating OFF
ACTUATOR RLY Actuator relay operation When the actuator relay is operating
ON
When the actuator relay is not operating OFF
ABS WARN LAMP ABS warning lamp
(Note 2) When ABS warning lamp is ON
ON
When ABS warning lamp is OFF OFF
OFF LAMP VDC OFF indicator lamp
(Note 2) When VDC OFF indicator lamp is ON
ON
When VDC OFF indicator lamp is OFF OFF
OFF SW VDC OFF switch ON/OFF VDC OFF switch ON
(When VDC OFF indicator lamp is ON)
ON
VDC OFF switch OFF
(When VDC OFF indicator lamp is OFF) OFF
SLIP LAMP SLIP indicator lamp
(Note 2) When SLIP indicator lamp is ON
ON
When SLIP indicator lamp is OFF OFF
BATTERY VOLT Battery voltage supplied to the ABS actuator
and electric unit (control unit) Ignition switch ON
10 – 16 V
GEAR Gear position determined by TCM 1st gear
2nd gear
3rd gear
4th gear
5th gear 1
2
3
4
5
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
Revision: April 20092010 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-89
< ECU DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
SLCT LVR POSI A/T selector lever position P position
R position
N position
D positionP
R
N
D
ENGINE SPEED With engine running With engine stopped
0 rpm
Engine running Almost in accor-
dance with tachome-
ter display
YAW RATE SEN Yaw rate detected by yaw rate/side/decel G
sensor When vehicle is stopped
Approx. 0 d/s
When vehicle turning −75 to 75 d/s
R POSI SIG Transmission range switch signal ON/OFF
condition A/T shift position = R position
ON
A/T shift position = other than R position OFF
4WD FAIL REQ
(Note 3) Transfer control unit fail-safe signal When transfer control unit is in fail-safe
mode
ON
When transfer control unit is normal OFF
N POSI SIG Transmission range switch signal ON/OFF
condition A/T shift position = N position
ON
A/T shift position = other than N position OFF
P POSI SIG Transmission range switch signal ON/OFF
condition A/T shift position = P position
ON
A/T shift position = other than P position OFF
CV1 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
CV2 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
SV1 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
SV2 VDC switch-over valve When actuator (switch-over valve) is ac-
tive (“ACTIVE TEST” with CONSULT-III)
or actuator relay is inactive (when in fail-
safe mode)
ON
When actuator (switch-over valve) is not
active and actuator relay is active (igni-
tion switch ON) OFF
2WD/4WD Drive axle 2WD model
2WD
4WD model 4WD
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
Revision: April 20092010 QX56

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)BRC-91
< ECU DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
NOTE:
• 1: Confirm tire pr essure is normal.
• 2: On and off timing for warning lamp and indicator lamp.
• 3: Only 4WD models.
- ABS warning lamp: Refer to BRC-82, "
Description".
- Brake warning lamp: Refer to BRC-83, "
Description".
- VDC OFF indicator lamp: Refer to BRC-84, "
Description".
- SLIP indicator lamp: Refer to BRC-86, "
Description".
TERMINAL LAYOUT
RELEASE SW NC Active booster signal status When brake pedal is depressed OFF
When brake pedal is released
ON
OHB FAIL OHB fail safe signal OHB is active
ON
OHB is inactive OFF
HBA FAIL HBA fail safe signal HBA is active
ON
HBA is inactive OFF
OHB SIG OHB operation In OHB fail-safe
ON
OHB is normal OFF
HBA SIG HBA operation In HBA fail-safe
ON
HBA is normal OFF
STP OFF RLY Stop lamp relay signal When stop lamp relay is ON
ON
When stop lamp relay is OFF OFF
Monitor item
Display content Data monitor
Condition Reference value in
normal operation
AWFIA0032ZZ
Revision: April 20092010 QX56

CCS
INTELLIGENT CRUISE CONTROL SYSTEMCCS-15
< FUNCTION DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B
N P A
Component Parts LocationINFOID:0000000005145981
1. ICC system display 2. Combination meter M23, M24 (with
built in information display) 3. ICC steering switch M102
4. ICC brake hold relay E134 5. ICC sensor E426. ICC brake switch E43
7. Stop lamp switch E38 8. ICC unit B13, B17 (view with luggage
side finisher lower LH removed)
ALOIA0014ZZ
Revision: April 20092010 QX56

CCS-20
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (ICC SENSOR INTEGRATED UNIT)
ACTIVE TEST
STOP LAMP SW
[On/Off] ××
Indicates [On/Off] status as judged from stop lamp switch signal (ECM trans-
mits stop lamp switch signal through CAN communication).
CRUISE LAMP
[On/Off] ××
Indicates [On/Off] status of MAIN switch indicator lamp output.
NP SW SIG
[On/Off] ××Indicates [On/Off] status as judged from transmission range switch signal
(ECM transmits transmission range switch signal through CAN communica-
tion).
STP LMP DRIVE
[On/Off] ××
Indicates [On/Off] status of ICC brake hold relay drive output.
PWR SUP MONI
[V] ××
Indicates IGN voltage input by ICC sensor integrated unit.
IDLE SW
[On/Off] ×Indicates [On/Off] status of idle switch read from ICC sensor integrated unit
through CAN communication (ECM transmits On/Off status through CAN
communication).
OWN VHCL
[On/Off] ×
Indicates [On/Off] status of own vehicle indicator output.
VHCL AHEAD
[On/Off] ×
Indicates [On/Off] status of vehicle ahead detection indicator output.
ICC WARNING
[On/Off] ×
Indicates [On/Off] status of ICC system warning lamp output.
BUZZER O/P
[On/Off] ×
Indicates [On/Off] status of ICC warning chime output.
ENGINE RPM
[rpm] ×
Indicates engine speed read from ICC sensor integrated unit through CAN
communication (ECM transmits engine speed through CAN communication).
WIPER SW
[OFF/LOW/HIGH] ×Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front wiper request
signal through CAN communication).
D RANGE SW
[On/Off] ×Indicates [On/Off] status of “D” or “DS” or “M” positions read from ICC sensor
integrated unit through CAN communication; ON when position “D” or “DS” or
“M” (TCM transmits shift position indicator lamp signal through CAN commu-
nication).
NP RANGE SW
[On/Off] ×Indicates shift position indicator lamp signal read from ICC sensor integrated
unit through CAN communication (TCM transmits shift position indicator lamp
signal through CAN communication).
VHCL SPD AT
[km/h] or [mph] ×Indicates vehicle speed calculated from A/T vehicle speed sensor read from
ICC sensor integrated unit through CAN communication (TCM transmits A/T
vehicle speed sensor signal through CAN communication).
GEAR
[1, 2, 3, 4, 5] ×Indicates A/T gear position read from ICC sensor integrated unit through CAN
communication (TCM transmits current gear position signal through CAN
communication).
MODE SIG
[OFF, ICC, ASCD] ×Indicates the active mode from ICC or ASCD [conventional (fixed speed)
cruise control mode].
SET DISP IND
[On/Off] ×
Indicates [On/Off] status of SET switch indicator output.
DISTANCE
[m] ×
Indicates the distance from the vehicle ahead.
RELATIVE SPD
[m/s] ×
Indicates the relative speed of the vehicle ahead.
Monitored Item [unit]
MAIN
SIGNALS SELECTION
FROM
MENU Description
Revision: April 20092010 QX56

CCS
DIAGNOSIS SYSTEM (ICC SENSOR INTEGRATED UNIT)
CCS-21
< FUNCTION DIAGNOSIS >
C
D E
F
G H
I
J
K L
M B
N P ANOTE:
• Never perform the active test while driving.
• “Active Test” cannot be started while ICC system warning lamp illuminates.
ECU IDENTIFICATION
Displays the part number of t he ICC sensor integrated unit.
Active test item Function
ICC BUZZER Activates/deactivates the ICC buzzer.
METER LAMP Turns ON/OFF the MAIN switch indicator and ICC system warning lamp.
NOTE:
Start the engine and perform active test.
STOP LAMP Drives the ICC brake hold relay and turns ON/OFF the stop lamp.
Revision: April 20092010 QX56

CCS-28
< COMPONENT DIAGNOSIS >
DTC 45 BRAKE SW/STOP L SW
DTC 45 BRAKE SW/STOP L SW
DTC 45 BRAKE SW/STOP L SWINFOID:0000000005145991
Regarding Wiring Diagram information, refer to CCS-48, "Wiring Diagram".
1.ECK CONNECTORS FOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connectors and connect them secu rely again. Erase DTC, then perform self-diagno-
sis of ICC system again.
Does the DTC reset?
YES >> • Poor connector connection. • Check connectors. Check connectors housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair as necessary. Erase DTC and perform ICC system
running test. Refer to CCS-8, "
ACTION TEST : ICC System Running Test".
NO >> GO TO 2
2.CHECK STOP LAMP SWITCH AND ICC BRAKE SWITCH
With data monitor, check if “STOP LAMP SW” and “BRAKE SW” are operating normally.
Do the monitor items display properly?
YES >> Replace ICC unit. Refer to CCS-71, "ICC Unit". Erase DTC and perform ICC system running test.
Refer to CCS-8, "
ACTION TEST : ICC System Running Test" .
NO >> • BRAKE SW: GO TO 3
• STOP LAMP SW: GO TO 5
3.ICC BRAKE SWITCH INSTALLATION AND ADJUSTMENT INSPECTION
Check ICC brake switch for proper installation and adjust if necessary.
Does ICC brake switch operate normally?
YES >> GO TO 4
NO >> After adjustment, erase DTC and perform ICC system running test. Refer to \
CCS-8, "
ACTION
TEST : ICC System Running Test" .
4.CHECK ICC BRAKE SWITCH
Check ICC brake switch.
Does the ICC brake switch check OK?
YES >> Replace ICC unit. Refer to CCS-71, "ICC Unit". Erase DTC and perform ICC system running test.
Refer to CCS-8, "
ACTION TEST : ICC System Running Test".
NO >> Replace ICC brake switch. Erase DTC and perform ICC system running test. Refer to CCS-8,
"ACTION TEST : ICC System Running Test".
5.CHECK STOP LAMP ILLUMINATION
Check stop lamp illumination.
Do the stop lamps operate normally?
YES >> GO TO 6
NO >> • Check stop lamp circuit. • Erase DTC and perform ICC system running test. Refer to CCS-8, "
ACTION TEST : ICC Sys-
tem Running Test".
6.CHECK ICC BRAKE HOLD RELAY
Revision: April 20092010 QX56

CCS
DTC 45 BRAKE SW/STOP L SWCCS-29
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B
N P A
1. Turn ignition switch OFF.
2. Remove ICC brake hold relay.
3. Check continuity between ICC brake hold relay terminals.
Are continuity results as specified?
YES >> GO TO 7
NO >> Replace ICC brake hold relay. Erase DTC and perform ICC system running test. Refer to CCS-8, "
ACTION
TEST : ICC System Running Test".
7.CHECK ICC BRAKE HOLD RELAY CIRCUIT
1. Disconnect ICC unit and stop lamp switch connectors.
2. Check continuity between ICC unit harness connector (A) B17 terminal 38 and ICC brake hold relay harness connector (B)
E134 terminal 6.
3. Check continuity between ICC unit harness connector (A) B17 terminal 38 and stop lamp switch harness connector (C) E38 ter-
minal 4.
Are continuity test results as specified?
YES >> Replace ICC unit. Refer to CCS-71, "ICC Unit". Erase DTC and perform ICC system running test.
Refer to CCS-8, "
ACTION TEST : ICC System Running Test" .
NO >> • Repair harness between ICC unit and ICC brake hold relay or stop lamp switch. • Erase DTC and perform ICC system running test. Refer to CCS-8, "
ACTION TEST : ICC Sys-
tem Running Test".
7 - 6 Continuity should not exist.
4 - 3 Continuity should exist.
SKIA6651E
Continuity should exist.
Continuity should exist.
ALOIA0007ZZ
Revision: April 20092010 QX56