air conditioning INFINITI QX56 2011 Factory Service Manual

HAC-82
< DTC/CIRCUIT DIAGNOSIS >[AUTOMATIC AIR CONDITIONING]
B2581, B2582 INTAKE SENSOR
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace intake sensor. Refer to
HAC-150, "
Removal and Installation".
Te r m i n a lCondition
Resistance: kΩ
Temperature: °C ( °F)
12 −
15 (5) 17.73
− 10 (14) 13.46
− 5 (23) 10.33
0 (32) 8.00
5 (41) 6.25
10 (50) 4.93
15 (59) 3.92
20 (68) 3.14
25 (77) 2.54
30 (86) 2.06
35 (95) 1.69
40 (104) 1.39 45 (113) 1.15
Revision: 2010 May2011 QX56

B262A, B262B, B2657, B2658 EXHAUST GAS/OUTSIDE ODOR DETECTING
SENSOR
HAC-83
< DTC/CIRCUIT DIAGNOSIS > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
B262A, B262B, B2657, B2658 EXHAU ST GAS/OUTSIDE ODOR DETECT-
ING SENSOR
DTC LogicINFOID:0000000006275918
DTC DETECTION LOGIC
NOTE:
 If DTC is displayed along with DTC U1000, first per form the trouble diagnosis for DTC U1000. Refer to HAC-
72, "DTC Logic".
 If DTC is displayed along with DTC U1010, fi rst perform the trouble diagnosis for DTC U1010. HAC-73,
"DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn ignition switch ON.
2. Select “Self Diagnostic Result” m ode of “HVAC” using CONSULT-III.
3. Check DTC.
Is DTC detected?
YES >> Refer to HAC-83, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006275919
1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10A fuse [No.4, lo cated in fuse block (J/B)]
NOTE:
Refer to PG-140, "
Fuse, Connector and Terminal Arrangement".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK EXHAUST GAS / OUTSIDE ODOR DETECTING SENSOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect exhaust gas / outside odor detecting sensor connector.
3. Turn ignition switch ON.
4. Check voltage between exhaust gas / outside odor detecting sensor harness and ground.
DTC Items
(CONSULT-III screen terms) DTC detection condition Possible cause
B262A GAS SENSOR Exhaust gas / outside odor detecting sensor
duty ratio 15% or less.
 Exhaust gas / outside odor detect-
ing sensor
 A/C auto amp.
 Harness or connectors (The sensor circuit is open or short-
ed.)
B262B
Exhaust gas / outside odor detecting sensor
duty ratio 85% or more.
B2657 CAS SENSOR CIRCUIT Exhaust gas / outside odor detecting sensor
duty ratio 0%.
B2658 Exhaust gas / outside odor detecting sensor
duty ratio 100%.
+
−Vol tag e
(Approx.)
Exhaust gas / outside odor detect-
ing sensor
Connector Terminal E117 1 Ground Battery voltage
Revision: 2010 May2011 QX56

HAC-84
< DTC/CIRCUIT DIAGNOSIS >[AUTOMATIC AIR CONDITIONING]
B262A, B262B, B2657, B2658 EX
HAUST GAS/OUTSIDE ODOR DETECTING
SENSOR
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector between exhaust gas / outside odor detecting sensor and fuse block
(J/B).
3.CHECK EXHAUST GAS / OUTSIDE ODOR DETECTING SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between exhaust gas / outsi de odor detecting sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair harness or connector.
4.CHECK EXHAUST GAS / OUTSIDE ODOR DETECTING SENSOR SIGNAL CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between exhaust gas / outside odor detecting sensor harness connector and ground.
Is the inspection result normal?
YES >> Replace exhaust gas / outside odor detecting sensor. Refer to HAC-151, "Removal and Installa-
tion".
NO >> GO TO 5.
5.CHECK EXHAUST GAS / OUTSIDE ODOR DETE CTING SENSOR SIGNAL CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect A/C auto amp.connector.
3. Check continuity between exhaust gas / outside odor detecting sensor harness connector and A/C auto
amp. connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair harness or connector.
6.CHECK EXHAUST GAS / OUTSIDE ODOR DETE CTING SENSOR SIGNAL CIRCUIT FOR GROUND
SHORT
Check continuity between exhaust gas / outside odor detecting sensor harness connector and ground.
Is the inspection result normal?
Exhaust gas / outside odor detect- ing sensor —Continuity
Connector Terminal
E117 2 Ground Existed
+
−Voltage
(Approx.)
Exhaust gas / outside odor detect-
ing sensor
Connector Terminal E117 3 Ground 5 V
Exhaust gas / outside odor detect- ing sensor A/C auto amp.
Continuity
Connector Terminal Connector Terminal
E117 3 M50 10 Existed
Exhaust gas / outside odor detect- ing sensor —Continuity
Connector Terminal
E117 3 Ground Not existed
Revision: 2010 May2011 QX56

B262A, B262B, B2657, B2658 EXHAUST GAS/OUTSIDE ODOR DETECTING
SENSOR
HAC-85
< DTC/CIRCUIT DIAGNOSIS > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
YES >> GO TO 7.
NO >> Repair harness or connector.
7.CHECK EXHAUST GAS / OUTSIDE ODOR DETE CTING SENSOR SIGNAL CIRCUIT FOR POWER
SHORT
Check voltage between exhaust gas / outside odor detecting sensor harness and ground.
Is the inspection result normal?
YES >> Replace A/C auto amp.. Refer to HAC-146, "Removal and Installation".
NO >> Repair harness or connector.
+
−Vol tag e
(Approx.)
Exhaust gas / outside odor detect-
ing sensor
Connector Terminal E117 3 Ground 0 V
Revision: 2010 May2011 QX56

HAC-86
< DTC/CIRCUIT DIAGNOSIS >[AUTOMATIC AIR CONDITIONING]
B2630, B2631 SUNLOAD
SENSOR (DRIVER SIDE)
B2630, B2631 SUNLOAD SEN SOR (DRIVER SIDE)
DTC LogicINFOID:0000000006275920
DTC DETECTION LOGIC
NOTE:
 If DTC is displayed along with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to HAC-
72, "DTC Logic".
 If DTC is displayed along with DTC U1010, fi rst perform the trouble diagnosis for DTC U1010. HAC-73,
"DTC Logic".
 Sunload sensor may register a malfunction when indoors, at dusk, or at other times when light is insufficient.
When performing the diagnosis indoors, use a lamp (60 W or more) that is pointed at the sunload sensor.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn ignition switch ON.
2. Select “Self Diagnostic Result” m ode of “HVAC” using CONSULT-III.
3. Check DTC.
Is DTC detected?
YES >> Refer to HAC-103, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006275921
1.CHECK SUNLOAD SENSOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect sunload sensor connector.
3. Turn ignition switch ON.
4. Check voltage between sunload sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK SUNLOAD SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect A/C auto amp. connector.
3. Check continuity between sunload sensor harne ss connector and A/C auto amp. harness connector.
DTCItems
(CONSULT-III screen terms) DTC detection condition Possible cause
B2630 SUNLOAD SENSOR Detected calorie at sunload sensor (driver side)
2832 W/m
2 (2436 kcal/m2·h) or more.
 Sunload sensor
 A/C auto amp.
 Harness or connectors
[The sensor circui t (driver side) is
open or shorted.]
B2631
Detected calorie at sunload sensor (driver side)
64.7 W/m
2 (55.6 kcal/m2·h) or less.
+
−Voltage
(Approx.)
Sunload sensor
Connector Terminal M74 2 Ground 5 V
Sunload sensor —Continuity
Connector Terminal
M74 3 Ground Existed
Revision: 2010 May2011 QX56

B2630, B2631 SUNLOAD SENSOR (DRIVER SIDE)HAC-87
< DTC/CIRCUIT DIAGNOSIS > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK SUNLOAD SENSOR
Check sunload sensor. Refer to HAC-104, "
Component Inspection".
Is the inspection result normal?
YES >> Replace A/C auto amp.. Refer to HAC-146, "Removal and Installation".
NO >> Replace sunload sensor. Refer to HAC-149, "
Removal and Installation".
4.CHECK SUNLOAD SENSOR POWER SUPPLY CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect A/C auto amp. connector.
3. Check continuity between sunload sensor harnes s connector and A/C auto amp. harness connector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair harness or connector.
5.CHECK SUNLOAD SENSOR POWER SU PPLY CIRCUIT FOR GROUND SHORT
Check continuity between sunload sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair harness or connector.
6.CHECK SUNLOAD SENSOR POWER SU PPLY CIRCUIT FOR POWER SHORT
1. Turn ignition switch ON.
2. Check voltage between sunload sensor harness connector and ground.
Is the inspection result normal?
YES >> Replace A/C auto amp.. Refer to HAC-146, "Removal and Installation".
NO >> Repair harness or connector.
Component InspectionINFOID:0000000006275922
1.CHECK SUNLOAD SENSOR
1. Turn ignition switch OFF.
2. Reconnect sunload sensor connector and A/C auto amp. connector.
3. Turn ignition switch ON.
4. Check input voltage from sunload sensor between A/C auto amp. harness connector and ground. Refer to
applicable table for normal value.
Sunload sensor A/C auto amp. Continuity
Connector Terminal Connector Terminal
M74 2 M50 9 Existed
Sunload sensor —Continuity
Connector Terminal
M74 2 Ground Not existed
+ −Vol tag e
(Approx.)
Sunload sensor
Connector Terminal M74 2 Ground 0 V
Revision: 2010 May2011 QX56

HAC-88
< DTC/CIRCUIT DIAGNOSIS >[AUTOMATIC AIR CONDITIONING]
B2630, B2631 SUNLOAD
SENSOR (DRIVER SIDE)
NOTE:
 When checking indoors, use a lamp of approximately 60 W. Move the lamp towards and away from the
sensor to check.
 The sunload amount produced by direct sunshine in fa ir weather is equivalent to approximately 0.770
kW/m
2 (662 kcal/m2·h).
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace sunload sensor. Refer to HAC-149, "
Removal and Installation".
+
−
A/C auto amp.
Connector Terminal M50 9 Ground
JPIIA1659GB
Revision: 2010 May2011 QX56

B2632, B2633 FRONT AIR MIX DOOR MOTOR (DRIVER SIDE)
HAC-89
< DTC/CIRCUIT DIAGNOSIS > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
B2632, B2633 FRONT AIR MIX DO OR MOTOR (DRIVER SIDE)
DTC LogicINFOID:0000000006275923
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn ignition switch ON.
2. Select “Self Diagnostic Result” m ode of “HVAC” using CONSULT-III.
3. Check DTC.
Is DTC detected?
YES >> Refer to HAC-89, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006275924
1.CHECK FRONT AIR MIX DOOR MOTOR ( DRIVER SIDE) COMMUNICATION SIGNAL
1. Turn ignition switch ON.
2. Check output waveform between front air mix door motor LH harness connector and ground with the oscil-
loscope.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK INSTALLATION OF FRONT AI R MIX DOOR MOTOR (DRIVER SIDE)
Check front air mix door motor (driver side) is properly installed. Refer to HAC-152, "
Exploded View".
Is the inspection result normal?
YES >> Replace front air mix door motor (driver side). Refer to HAC-153, "AIR MIX DOOR MOTOR :
Removal and Installation".
NO >> Repair or replace malfunctioning part.
DTC Items
(CONSULT-III screen terms) DTC detection condition Possible cause
B2632
DR AIR MIX DOOR MOT Front air mix door motor (driver side)
PBR position 95% or more
 Front air mix door
motor (driver side)
(PBR internal circuit is open or short-
ed)
 Front air mix door motor (driver side)
installation condition
 A/C auto amp.
 Harness and connector (LIN communication line is open or
shorted)
B2633
Front air mix door motor (driver side)
PBR position 5% or less
+
−Output waveform
Front air mix door motor LH
Connector Terminal
M252 3 Ground
SJIA1453J
Revision: 2010 May2011 QX56

HAC-90
< DTC/CIRCUIT DIAGNOSIS >[AUTOMATIC AIR CONDITIONING]
B2632, B2633 FRONT AIR MIX
DOOR MOTOR (DRIVER SIDE)
3.CHECK FRONT AIR MIX DOOR MOTOR (DRIVE R SIDE) COMMUNICATION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front air mix door motor LH and A/C auto amp. connector.
3. Check continuity between front air mix door moto r LH harness connector and A/C auto amp. harness con-
nector.
Is the inspection result normal?
YES >> Replace A/C auto amp.. Refer to HAC-146, "Removal and Installation".
NO >> Repair harness or connector.
Front air mix door motor LH A/C auto amp. Continuity
Connector Terminal Connector Terminal
M252 3 M50 16 Existed
Revision: 2010 May2011 QX56

B2634, B2635 FRONT AIR MIX DOOR MOTOR (PASSENGER SIDE)
HAC-91
< DTC/CIRCUIT DIAGNOSIS > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
B2634, B2635 FRONT AIR MIX DO OR MOTOR (PASSENGER SIDE)
DTC LogicINFOID:0000000006275925
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn ignition switch ON.
2. Select “Self Diagnostic Result” m ode of “HVAC” using CONSULT-III.
3. Check DTC.
Is DTC detected?
YES >> Refer to HAC-91, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006275926
1.CHECK FRONT AIR MIX DOOR MOTOR (P ASSENGER SIDE) COMMUNICATION SIGNAL
1. Turn ignition switch ON.
2. Check output waveform between front air mi x door motor RH harness connector and ground with the
oscilloscope.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK INSTALLATION OF FRONT AIR MIX DOOR MOTOR (PASSENGER SIDE)
Check front air mix door motor (passenger side) is properly installed. Refer to HAC-152, "
Exploded View".
Is the inspection result normal?
YES >> Replace front air mix door motor (passenger side). Refer to HAC-153, "AIR MIX DOOR MOTOR :
Removal and Installation".
DTCItems
(CONSULT-III screen terms) DTC detection condition Possible cause
B2634
PASS AIR MIX DOOR MOT Front air mix door motor (passenger
side) PBR position 95% or more
 Front air mix door motor (passenger
side)
(PBR internal circuit is open or short-
ed)
 Front air mix door motor (passenger side) installation condition
 A/C auto amp.
 Harness and connector
(LIN communication line is open or
shorted)
B2635
Front air mix door motor (passenger
side) PBR position 5% or less
+
−Output waveform
Front air mix door motor RH
Connector Terminal
M255 3 Ground
SJIA1453J
Revision: 2010 May2011 QX56