light INFINITI QX56 2011 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 2727 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEMEXL-17
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
ACTIVE ADAPTIVE FRONT-LIGHTING SYSTEM : Fail-SafeINFOID:0000000006422028
HEADLAMP AIMING CONTROL (MANUAL)
DTC Fail-](/img/42/57033/w960_57033-2726.png "INFINITI QX56 2011 Factory Service Manual
SYSTEMEXL-17
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
ACTIVE ADAPTIVE FRONT-LIGHTING SYSTEM : Fail-SafeINFOID:0000000006422028
HEADLAMP AIMING CONTROL (MANUAL)
DTC Fail-")
SYSTEMEXL-17
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
ACTIVE ADAPTIVE FRONT-LIGHTING SYSTEM : Fail-SafeINFOID:0000000006422028
HEADLAMP AIMING CONTROL (MANUAL)
DTC Fail-safe AFS OFF indicator lamp Cancellation
U1000: CAN COMM CIRCUIT Right and left swivel motors
stop at the position when DTC
is detected.
Right and left aiming motors stop at the position when DTC
is detected. Blinks 1 second each. Ignition switch OFF
U1010: CONTROL UNIT (CAN) Right and left swivel motors
stop at the position when DTC
is detected.
Right and left aiming motors
stop at the position when DTC
is detected. Blinks 1 second each. Ignition switch OFF
B2503: SWIVEL ACTUATOR [RH] Right swivel motors stop at the
position when DT C is detected.
The signal, approximately 2 V
decreased from the levelizer
signal when DTC detected, is
output. Blinks 1 second each. Ignition switch OFF
B2504: SWIVEL ACTUATOR [LH] Left swivel motors stop at the
position when DT C is detected.
The signal, approximately 2 V decreased from the levelizer
signal when DTC detected, is
output. Blinks 1 second each. Ignition switch OFF
B2513: HI SEN UNUSUAL [FR] Right and left aiming motors
stop at the position when DTC
is detected. — Ignition switch OFF
B2514: HI SEN UNUSUAL [RR] Right and left aiming motors
stop at the position when DTC
is detected. — Ignition switch OFF
C0126: ST ANG SEN SIG Right and left swivel motor
swivel angle returns to 0 ° and
fixed. Blinks 1 second each. Ignition switch OFF
B2516: SHIFT SIG [P, R] Right and left swivel motor
swivel angle returns to 0 ° and
fixed. Blinks 1 second each. Ignition switch OFF
B2517: VEHICLE SPEED SIG Right and left swivel motor
swivel angle returns to 0 ° and
fixed.
Right and left aiming motors stop at the position when DTC
is detected. Blinks 1 second each. Ignition switch OFF
B2519: LEVELIZER CALIB Right and left aiming motors
stop at the position when DTC
is detected. —
When the levelizer adjustment is
completed.
C0428: ST ANGLE SEN CALIB Right and left swivel motor
swivel angle returns to 0 ° and
fixed. Blinks 1 second each.
When the steering angle sensor
neutral position registration is
competed.
B2521: ECU CIRC Right and left swivel motors
stop at the position when DTC
is detected.
Right and left aiming motors stop at the position when DTC
is detected. Blinks 1 second each. Ignition switch OFF
Revision: 2010 May2011 QX56
Page 2728 of 5598
![INFINITI QX56 2011 Factory Service Manual
EXL-18
< SYSTEM DESCRIPTION >[XENON TYPE]
SYSTEM
HEADLAMP AIMING CONTROL (MA NUAL) : System Description
INFOID:0000000006216751
The headlamp levelizer adjusts the headlamp light axis upward and downw](/img/42/57033/w960_57033-2727.png "INFINITI QX56 2011 Factory Service Manual
EXL-18
< SYSTEM DESCRIPTION >[XENON TYPE]
SYSTEM
HEADLAMP AIMING CONTROL (MA NUAL) : System Description
INFOID:0000000006216751
The headlamp levelizer adjusts the headlamp light axis upward and downw")
EXL-18
< SYSTEM DESCRIPTION >[XENON TYPE]
SYSTEM
HEADLAMP AIMING CONTROL (MA NUAL) : System Description
INFOID:0000000006216751
The headlamp levelizer adjusts the headlamp light axis upward and downward with the aiming motor inte-
grated in the front combination lamp.
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram
INFOID:0000000006213901
TURN SIGNAL AND HAZARD WARNING LA MP SYSTEM : System Description
INFOID:0000000006213902
OUTLINE
Turn signal and the hazard warning lamp is controlled by combination switch reading function, flasher control
function and auto hazard function of BCM.
TURN SIGNAL LAMP OPERATION
BCM detects the combination switch conditi on by the combination switch reading function.
BCM supplies voltage to the right (left) turn signal la mp circuit when the ignition switch is turned ON and the
turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the
hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION
BCM transmits the turn indicator signal to the comb ination meter via CAN communication while the turn sig-
nal lamp and the hazard warning lamp operating.
Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION
BCM detects the turn signal lamp ci rcuit status from the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-
nal lamp operating.
NOTE:
The blinking speed is normal while operating the hazard warning lamp.
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System Di-
JPLIA0180GB
Revision: 2010 May2011 QX56
Page 2729 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEMEXL-19
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
agramINFOID:0000000006213903
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System De-
scription
INFOID](/img/42/57033/w960_57033-2728.png "INFINITI QX56 2011 Factory Service Manual
SYSTEMEXL-19
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
agramINFOID:0000000006213903
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System De-
scription
INFOID")
SYSTEMEXL-19
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
agramINFOID:0000000006213903
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System De-
scription
INFOID:0000000006213904
OUTLINE
Parking, license plate, side marker and tail lamps ar e controlled by combination switch reading function and
headlamp control function of BCM, and re lay control function of IPDM E/R.
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS OPERATION
BCM detects the combination switch conditi on by the combination switch reading function.
BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the ON/OFF condition of the pa rking, license plate, side marker and tail lamps.
Parking, license plate, side marker and tail lamps ON condition- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
IPDM E/R turns the integrated tail lamp relay ON and tu rns the parking, license plate, side marker and tail
lamps ON according to the position light request signal.
Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : Fail-safe
INFOID:0000000006213905
CAN COMMUNICATION CONTROL
When CAN communication with BCM is impossible, IPDM E/R performs fail-safe control. After CAN communi-
cation recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
*: With daytime running light system
FRONT FOG LAMP SYSTEM
JMLIA0687GB
Control part Fail-safe operation
Parking lamps
License plate lamps
Illuminations
Tail lamps Turns ON the tail lamp relay and daytime running light relay
* when the ignition switch
is turned ON
Turns OFF the tail lamp relay and daytime running light relay
* when the ignition switch
is turned OFF
Revision: 2010 May2011 QX56
Page 2730 of 5598
![INFINITI QX56 2011 Factory Service Manual
EXL-20
< SYSTEM DESCRIPTION >[XENON TYPE]
SYSTEM
FRONT FOG LAMP SYSTEM : System Diagram
INFOID:0000000006213906
FRONT FOG LAMP SYSTEM : System DescriptionINFOID:0000000006213907
OUTLINE
Front fog lam](/img/42/57033/w960_57033-2729.png "INFINITI QX56 2011 Factory Service Manual
EXL-20
< SYSTEM DESCRIPTION >[XENON TYPE]
SYSTEM
FRONT FOG LAMP SYSTEM : System Diagram
INFOID:0000000006213906
FRONT FOG LAMP SYSTEM : System DescriptionINFOID:0000000006213907
OUTLINE
Front fog lam")
EXL-20
< SYSTEM DESCRIPTION >[XENON TYPE]
SYSTEM
FRONT FOG LAMP SYSTEM : System Diagram
INFOID:0000000006213906
FRONT FOG LAMP SYSTEM : System DescriptionINFOID:0000000006213907
OUTLINE
Front fog lamp is controlled by combination switch r eading function and front fog lamp control function of BCM,
and relay control function of IPDM E/R.
FRONT FOG LAMP OPERATION
BCM detects the combination switch conditi on by the combination switch reading function.
BCM transmits the front fog lights request signal to IPDM E/R via CAN communication according to the front
fog lamp ON condition.
Front fog lamp ON condition- Front fog lamp switch ON and any of the followings. (except for the high beam ON)
Lighting switch 2ND
Lighting switch AUTO (auto light function ON judgment)
IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the front
fog lights request signal.
FRONT FOG LAMP SYSTEM : Fail-SafeINFOID:0000000006422123
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
EXTERIOR LAMP BATTERY SAVER SYSTEM
EXTERIOR LAMP BATTERY SAVE R SYSTEM : System DiagramINFOID:0000000006213908
JMLIA1154GB
Control part Fail-safe operation
Front fog lamp Front fog lamp relay OFF
JPLIA1037GB
Revision: 2010 May2011 QX56
Page 2731 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEMEXL-21
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
EXTERIOR LAMP BATTERY SAVE R SYSTEM : System DescriptionINFOID:0000000006213909
OUTLINE
Exterior lamp battery save](/img/42/57033/w960_57033-2730.png "INFINITI QX56 2011 Factory Service Manual
SYSTEMEXL-21
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
EXTERIOR LAMP BATTERY SAVE R SYSTEM : System DescriptionINFOID:0000000006213909
OUTLINE
Exterior lamp battery save")
SYSTEMEXL-21
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
EXTERIOR LAMP BATTERY SAVE R SYSTEM : System DescriptionINFOID:0000000006213909
OUTLINE
Exterior lamp battery saver system is c ontrolled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function
BCM turns the exterior lamp* OFF after a period of ti me to prevent the battery from over-discharge when the
ignition switch is turned OFF with the exterior lamp ON.
*: Headlamp (LO/HI), parking lamp, tail lamp, side marker lamp, license plate lamp and front fog lamp
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM activates the timer and turns the exterior lamp OFF 5 minutes after the ignition switch is turned from ON
→ OFF with the exterior lamps ON.
NOTE:
Headlamp control function turns the exterior lamps ON normally when the ignition switch is turned ACC or
the engine started (both before and after the exte rior lamp battery saver is turned OFF).
The timer starts at the time that the lighting switch is turned from OFF → 1ST or 2ND with the exterior lamp
OFF.
Revision: 2010 May2011 QX56
Page 2733 of 5598
![INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (BCM)EXL-23
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
HEADLAMP
HEADLAMP : CONSULT-III Func tion (BCM - HEAD LAMP)INFOID:0000000006213911
WORK SUPPORT
CONS](/img/42/57033/w960_57033-2732.png "INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (BCM)EXL-23
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
HEADLAMP
HEADLAMP : CONSULT-III Func tion (BCM - HEAD LAMP)INFOID:0000000006213911
WORK SUPPORT
CONS")
DIAGNOSIS SYSTEM (BCM)EXL-23
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
HEADLAMP
HEADLAMP : CONSULT-III Func tion (BCM - HEAD LAMP)INFOID:0000000006213911
WORK SUPPORT
CONSULT screen item Indication/Unit Description
Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)
SLEEP>OFF While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
RUN>ACC While turning power supply position
from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN While turning power su
pply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT While turning power su
pply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF While turning power supply position from “ACC” to “OFF”
OFF>LOCK While turning power supply position from “OFF” to “LOCK”
OFF>ACC While turning power supply position from “OFF” to “ACC”
ON>CRANK While turning po wer supply position from “IGN” to “CRANKING”
OFF>SLEEP While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode
LOCK Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)
OFF Power supply position
is “OFF” (Ignition switch OFF with steering
is unlocked.)
ACC Power supply position is “ACC” (Ignition switch ACC)
ON Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN Power supply posi
tion is “RUN” (Ignition switch ON with engine
running)
CRANKING Power supply position is “CRANKING” (At engine cranking)
IGN Counter 0 - 39 The number of times that ignition switch is turned ON after DTC is detected
The number is 0 when a malfunction is detected now.
The number increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF → ON.
The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Service item Setting item Setting
CUSTOM A/LIGHT SETTING MODE 1*
1Normal
MODE 2 More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)
MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
MODE 4 Less sensitive setting than normal setting (Turns ON later than normal operation)
Revision: 2010 May2011 QX56
Page 2734 of 5598
![INFINITI QX56 2011 Factory Service Manual
EXL-24
< SYSTEM DESCRIPTION >[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
*1: Factory setting
*
2: For models for Canada, this item is displayed but is not operated.
DATA MONITOR
BATTERY SAVER SET On*1With th](/img/42/57033/w960_57033-2733.png "INFINITI QX56 2011 Factory Service Manual
EXL-24
< SYSTEM DESCRIPTION >[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
*1: Factory setting
*
2: For models for Canada, this item is displayed but is not operated.
DATA MONITOR
BATTERY SAVER SET On*1With th")
EXL-24
< SYSTEM DESCRIPTION >[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
*1: Factory setting
*
2: For models for Canada, this item is displayed but is not operated.
DATA MONITOR
BATTERY SAVER SET On*1With the exterior lamp battery saver function
Off Without the exterior lamp battery saver function
ILL DELAY SET MODE 1*
145 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE 2
Without the
function
MODE 3 30 sec.
MODE 4 60 sec.
MODE 5 90 sec.
MODE 6 120 sec.
MODE 7 150 sec.
MODE 8 180 sec.
AUTO LIGHT LOGIC SET*
2
MODE 1*1With twilight ON custom & with wiper INT, LO and HI
MODE 2 With twilight ON custom & with wiper LO and HI
MODE 3 With twilight ON custom & without
MODE 4 Without twilight ON custom & with wiper INT, LO and HI
MODE 5 Without twilight ON custom & with wiper LO and HI
MODE 6 Without twilight ON custom & without
Service item Setting item Setting
Monitor item
[Unit] Description
PUSH SW
[On/Off] The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run] The engine status received from ECM via CAN communication
VEH SPEED 1
[km/h] The value of the vehicle speed received from combination meter via CAN communi-
cation
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TA I L L A M P S W
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW
[On/Off]
NOTE:
This item is indicated, but can not monitored
Revision: 2010 May2011 QX56
Page 2735 of 5598
![INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (BCM)EXL-25
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
ACTIVE TEST
*: Only models for Canada display this item.
FLASHER
FLASHER : CONSULT-III F unction (BC](/img/42/57033/w960_57033-2734.png "INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (BCM)EXL-25
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
ACTIVE TEST
*: Only models for Canada display this item.
FLASHER
FLASHER : CONSULT-III F unction (BC")
DIAGNOSIS SYSTEM (BCM)EXL-25
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
ACTIVE TEST
*: Only models for Canada display this item.
FLASHER
FLASHER : CONSULT-III F unction (BCM - FLASHER)INFOID:0000000006213912
WORK SUPPORT
DOOR SW-DR
[On/Off] The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off] The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off] The switch status input from rear door switch RH
DOOR SW- RL
[On/Off] The switch status input from rear door switch LH
DOOR SW-BK
[On/Off] The switch status input from back door switch
OPTICAL SENSOR
[On/Off] The sensor status input from optical sensor
OPTI SEN (DTCT)
[V] The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V] The value of outside brightness voltage filtered by BCM
Monitor item
[Unit] Description
Test item Operation Description
TAIL LAMP On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off Stops the tail lamp request signal transmission
HEAD LAMP Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off Stops the high & low beam request signal transmission
FR FOG LAMP On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON
Off Stops the front light request signal transmission
RR FOG LAMP On
NOTE:
This item is indicated, but can not tested
Off
DAYTIME RUNNING LIGHT* On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON (daytime running light system)
Off Stops the front light request signal transmission (daytime running light
system)
ILL DIM SIGNAL On Transmits the dimmer signal to combination meter via CAN communi-
cation and dims combination meter
Transmits the dimmer signal to AV control unit and dims display
Off Stops the dimmer signal transmission
Revision: 2010 May2011 QX56
Page 2739 of 5598
![INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (IPDM E/R)EXL-29
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
CONSULT-III Function (IPDM E/R)INFOID:0000000006368067
APPLICATION ITEM
CONSULT-III performs th](/img/42/57033/w960_57033-2738.png "INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (IPDM E/R)EXL-29
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
CONSULT-III Function (IPDM E/R)INFOID:0000000006368067
APPLICATION ITEM
CONSULT-III performs th")
DIAGNOSIS SYSTEM (IPDM E/R)EXL-29
< SYSTEM DESCRIPTION > [XENON TYPE]
C
D
E
F
G H
I
J
K
M A
B
EXL
N
O P
CONSULT-III Function (IPDM E/R)INFOID:0000000006368067
APPLICATION ITEM
CONSULT-III performs the following functi ons via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
Refer to PCS-22, "DTCIndex".
DATA MONITOR
Monitor item
Oil pressure warning lamp does not operate Perform auto active test.
Does the oil pressure warning
lamp blink?YES
Harness or connector be-
tween IPDM E/R and oil
pressure switch
Oil pressure switch
IPDM E/R
NO CAN communication signal
between IPDM E/R and
BCM
CAN communication signal
between BCM and combi-
nation meter
Combination meter
Symptom Inspection contents Possible cause
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item [Unit] MAIN SIG-
NALS Description
RAD FAN REQ
[1/2/3/4] ×Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On] ×Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On] ×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On] ×Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On] ×Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On] ×Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi] ×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P] ×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK] ×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On] Displays the status of the ignition switch ON signal received from BCM via CAN
communication.
IGN RLY
[Off/On] ×
Displays the status of the ignition relay judged by IPDM E/R.
Revision: 2010 May2011 QX56
Page 2742 of 5598
![INFINITI QX56 2011 Factory Service Manual
EXL-32
< SYSTEM DESCRIPTION >[XENON TYPE]
DIAGNOSIS SYSTEM (AFS)
DIAGNOSIS SYSTEM (AFS)
CONSULT-III Function (ADAPTIVE LIGHT)INFOID:0000000006213915
APPLICATION ITEM
WORK SUPPORT
*: Adjusts the steer](/img/42/57033/w960_57033-2741.png "INFINITI QX56 2011 Factory Service Manual
EXL-32
< SYSTEM DESCRIPTION >[XENON TYPE]
DIAGNOSIS SYSTEM (AFS)
DIAGNOSIS SYSTEM (AFS)
CONSULT-III Function (ADAPTIVE LIGHT)INFOID:0000000006213915
APPLICATION ITEM
WORK SUPPORT
*: Adjusts the steer")
EXL-32
< SYSTEM DESCRIPTION >[XENON TYPE]
DIAGNOSIS SYSTEM (AFS)
DIAGNOSIS SYSTEM (AFS)
CONSULT-III Function (ADAPTIVE LIGHT)INFOID:0000000006213915
APPLICATION ITEM
WORK SUPPORT
*: Adjusts the steering angle sensor neutral position on ABS actuator and electrical unit (control unit) side. Refer to
BRC-64, "Work Pro-
cedure".
DATA MONITOR
*: The swivel angle "0°" (feedback value) of the swivel position sensor signal may differ from the swivel angle "0 °" of the swivel motor
(AFS control unit command value). This causes that the swivel motor initializes the value based on the step number from the sto pper.
ACTIVE TEST
Diagnostic mode Description
Ecu Identification Allows confirmation of AFS control unit part number.
Self Diagnostic Result Displays the diagnosis results judged by AFS control unit.
Work support Sets each sensor.
Data monitor Indicates AFS control unit input data in real time.
Active test Provides the drive signal to the load. Checks operation.
Service item Description
ST ANG SEN ADJUSTMENT
*—
LEVELIZER ADJUSTMENT Adjusts the height sensor signal output value (AFS control unit recognized) in the un-
loaded vehicle condition.
Monitor item
[Unit] Description
STR ANGLS SIG
[deg] The steering angle value judged by the steering angle sensor signal received from
the steering angle sensor via CAN communication
VHCL SPD
[km/h] The vehicle speed signal value from the combination meter via CAN communication
SLCT LVR POSI
[P/R/N/D/M/FF] The selector lever status judged by the position indicator signal received from TCM
via CAN communication
HEAD LAMP
[On/Off] The headlamp On/Off status judged by the low beam headlamp (ON) signal received
from IPDM E/R via
CAN communication
AFS SW
[On/Off] The AFS On/Off status judged by AFS control unit
HI SEN OTP RR
[V] The rear height sensor signal voltage value input from the rear height sensor
HI SEN OTP FR
[V] The front height sensor signal voltage value input from the front height sensor
LEV ACTR VLTG
[%] The ratio value to the battery voltage generated by the levelizer activation signal con-
trol value judged by AFS control unit
SWVL SEN RH
*
[deg] The head lamp swivel angle value judged by AFS control unit received from the swiv-
el position sensor signal input from the swivel actuator
SWVL SEN LH
*
[deg]
SWVL ANGLE RH
*
[deg]
The swivel angle command value to the swivel motor judged by AFS control unit
SWVL ANGLE LH
*
[deg]
Revision: 2010 May2011 QX56