fuel injector INFINITI QX56 2011 Factory User Guide

EC-78
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(R)
2
(R) 175
(B) Fuel injector No. 8 (HI)
Fuel injector No. 5 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
3
(G)
4
(G) 175
(B) Fuel injector No. 3 (LO)
Fuel injector No. 2 (LO)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
5
(B/R) — ECM ground — — —
JPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
Revision: 2010 May2011 QX56

ECM
EC-79
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
6
(R) 7
(R) 175
(B) Fuel injector No. 3 (HI)
Fuel injector No. 2 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
8
(G) 9
(G) 175
(B) Fuel injector No. 8 (LO)
Fuel injector No. 5 (LO)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
10
(B) — ECM ground — — —
11
(BR) 175
(B) PNP switch Input [Ignition switch: ON]
 Selector lever: P or N position
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON]
 Selector lever: Except above posi- tion 0 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
Revision: 2010 May2011 QX56

EC-82
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
37
(V) 175
(B) Cooling fan speed Input [Ignition switch: ON]
 Engine stopped
5 V
[Engine is running]
 Idle speed
 After warm-up condition BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Idle speed
 Before warm-up condition BATTERY VOLTAGE
(11 - 14 V)
39
(P/B) 45
(L/O) Power steering pressure sensor Input [Engine is running]
 Steering wheel: Being turned
0.5 - 4.5 V
[Engine is running]
 Steering wheel: Not being turned 0.4 - 0.8 V
40
(W/L) —Sensor ground
(Fuel rail pressure sensor/En-
gine coolant temperature sen-
sor/Engine oil temperature
sensor) —— —
42
(L/Y) 40
(W/L) Engine oil temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
oil temperature.
45
(L/O) —Sensor ground
(Power steering pressure sen-
sor/ Low fuel pressure sensor/
Electrically-controlled cooling
fan coupling) —— —
46
(SB) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: OFF] 1.5 V
47
(G) 175
(B) Heated oxygen sensor 2 heater
(bank 1)
Input[Engine is running]
 Engine speed: Below 3,600 rpm af-
ter the following conditions are met
- Engine: after warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 10 V
[Ignition switch: ON]
 Engine: Stopped
[Engine is running]
 Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3332ZZ
JPBIA3733ZZ
JMBIA0037GB
Revision: 2010 May2011 QX56

ECM
EC-83
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
48
(L/W) 175
(B) A/F sensor 1 heater (bank 1) Input [Engine is running]
 Warm-up condition
 Idle speed
(More than 140 seconds after start-
ing engine) 2.9 - 8.8 V
49
(LG/
B) 175
(B) Intake valve timing control sole-
noid valve (bank 1)
Output[Engine is running]
 Warm-up condition
 Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000rpm 7 - 12 V
51
(R) 175
(B) Fuel injector driver power supply Output [Engine is running]
 Warm-up condition
 Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: OFF] 1.5 V
52
(L/R) 175
(B) Heated oxygen sensor 2 heater
(bank 2)
Output[Engine is running]
 Engine speed: Below 3,600 rpm af-
ter the following conditions are met
- Engine: after warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 10 V
[Ignition switch: ON]
 Engine: Stopped
[Engine is running]
 Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14 V)
53
(SB) 175
(B) A/F sensor 1 heater (bank 2) Output [Engine is running]
 Warm-up condition
 Idle speed
(More than 140 seconds after start-
ing engine) 2.9 - 8.8 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3361ZZ
JMBIA0038GB
JMBIA0037GB
JPBIA3361ZZ
Revision: 2010 May2011 QX56

EC-88
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
101
(R)
102 (R) 175
(B) Fuel injector No. 1 (HI)
Fuel injector No. 6 (HI)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
103 (G)
104 (G) 175
(B) Fuel injector No. 7 (LO)
Fuel injector No. 4 (LO)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
105
(L/W) 175
(B) High pressure fuel pump (HI) Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
JPBIA3340ZZ
JPBIA3341ZZ
Revision: 2010 May2011 QX56

ECM
EC-89
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
106
(R)
107 (R) 175
(B) Fuel injector No. 7 (HI)
Fuel injector No. 4 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
108 (G)
109 (G) 175
(B) Fuel injector No. 1 (LO)
Fuel injector No. 6 (LO)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
11 0
(L/B) 175
(B) High pressure fuel pump (LO) Input [Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
JPBIA3342ZZ
JPBIA3343ZZ
Revision: 2010 May2011 QX56

EC-90
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
111
(R) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
11 2
(SB) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
11 4 (B) — ECM ground — — —
11 5 (B) — ECM ground — — —
120 (Y) 175
(B) EVAP canister vent control valve Output [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
122
(BR/ W) 175
(B) VVEL actuator motor relay abort
signal (VVEL control module)
Input [Ignition switch: ON] 0 V
123
(V/R) 175
(B) Throttle control mo
tor relay Output [Ignition switch: ON
→ OFF] 0 - 1.0 V
↓
BATTERY VOLTAGE
(11 - 14 V)
↓
0 V
[Ignition switch: ON] 0 - 1.0 V
125
(GR) 175
(B) Fuel pump control module
(FPCM)
Output[When cranking engine] 0 - 0.5 V
[Engine is running]
 Warm-up condition
0 - 4.0 V
126 (O) 129
(P/L) Accelerator pedal position sen-
sor 2
Input[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully released
0.28 - 0.48 V
[Ignition switch: ON]
 Engine: Stopped
 Accelerator pedal: Fully depressed 2.0 - 2.5 V
128 (Y) 130
(R) ASCD steering switch Input [Ignition switch: ON]
 ASCD steering switch: OFF
4 V
[Ignition switch: ON]
 MAIN switch: Pressed 0 V
[Ignition switch: ON]
 CANCEL switch: Pressed 1 V
[Ignition switch: ON]
 RESUME/ACCELERATE switch: Pressed 3 V
[Ignition switch: ON]
 SET/COAST switch: Pressed 2 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3344ZZ
Revision: 2010 May2011 QX56

EC-94
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
DTC No. Detected items Engine operating condition in fail-safe mode
U0113
U1003
U1024 Can communication circuit VVEL actuator
motor relay is turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P0011
P0021 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0087 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0088 Engine speed is limited.
P008A Low fuel pressure control
system Engine torque is limited.
P0090 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit
Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT-III displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT-III display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx. 4 minutes or more after
engine starting 80
°C (176 °F)
Except as shown above 40 - 80 °C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0190 FRP sensor  Engine speed is limited.
 High pressure fuel pump is activated at maximum discharge pressure.
P0201
P0202
P0203
P0204
P0205
P0206
P0207
P0208 Injector  Engine torque is limited.
 Fuel injection shut-off of malfunction cylinder.
 Mixture ratio feedback control does not function.
 Idle engine speed is increased.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0605 ECM (When ECM calculation function is malfunctioning:)
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0607 ECM VVEL actuator motor relay is
turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
Revision: 2010 May2011 QX56

ECM
EC-95
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P062B ECM Type1
 Engine torque is limited.
 Idle engine speed is increased.
 Fuel injector power supply shut-off.
 High fuel pressure limitation.
Typ e2
 Engine torque is limited.
 Fuel injection shut-off of malfunction cylinder.
 Mixture ratio feedback control does not function.
 Idle engine speed is increased.
P0643 Sensor power supply ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P1087
P1088 VVEL control function VVEL of no
rmal bank is controlled at VVEL angle of abnormal bank.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1089
P1092 VVEL control shaft position
sensor VVEL value is maintained at a fixed angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut
P1197 Out of gas  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P1608 VVEL control shaft position
sensor VVEL actuator motor relay is turned off, an
d VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1090
P1093 VVEL actuator motor VVEL of no
rmal bank is controlled at VVEL angle of abnormal bank.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
VVEL actuator motor relay is turned off, an d VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1091 VVEL actuator motor rela
y VVEL actuator motor relay is turned off, an d VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1197 Out of gas  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P2101 Electric throttle control
function ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2118 Throttle control motor ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2119 Electric throttle control ac-
tuator
(When electric throttle control actuator does not function properly due to the return spring
malfunction:)
ECM controls the electric throttle actuator by regulating the throttle opening around the
idle position. The engine speed will not rise more than 2,000 rpm.
(When throttle valve opening angle in fail-safe mode is not in specified range:)
ECM controls the electric throttle control actuator because of regulating the throttle open-
ing to 20 degrees or less.
(When ECM detects the throttle valve is stuck open:)
While the vehicle is being driven, it slows down gradually by fuel cut. After the vehicle
stops, the engine stalls.
The engine can restart in the N or P position, and engine speed will not exceed 1,000 rpm
or more.
P1290
P2100
P2103 Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P1606 VVEL control module VVEL
actuator motor relay is turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P1805 Brake switch ECM controls the electric throttle control
actuator by regulating the throttle opening to a
small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal
When accelerating Poor acceleration
DTC No. Detected items Engine operating condition in fail-safe mode
Revision: 2010 May2011 QX56

EC-98
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
NOTE:
*: If “P1197” is displayed with other DTC in priority 1, perform trouble diagnosis for “P1197” first.
DTC IndexINFOID:0000000006217733
×
:Applicable —: Not applicable
2  P0031 P0032 P0051 P0052 Air fuel ratio (A/F) sensor 1 heater
 P0037 P0038 P0057 P0058 Heated oxygen sensor 2 heater
 P0075 P0081 Intake valve timing control solenoid valve
 P0130 P0131 P0132 P0133 P0150 P0151 P0152 P015 3 P2A00 P2A03 Air fuel ratio (A/F) sensor 1
 P0137 P0138 P0139 P0157 P0158 P0159 Heated oxygen sensor 2
 P0190 - P0193 FRP sensor
 P0441 EVAP control system purge flow monitoring
 P0443 P0444 P0445 EVAP canister purge volume control solenoid valve
 P0447 P0448 EVAP canister vent control valve
 P0451 P0452 P0453 EVAP control system pressure sensor
 P0550 Power steering pressure sensor
 P0603 ECM power supply
 P0710 P0717 P0720 P0729 P0730 P0731 P0732 P0733 P0734 P0735 P0740 P0744 P0745 P0750 P0775 P0780 P0795 P1730 P1734 P2713 P2722 P2731 P2807 A/T related sensors, solenoid valves and switches
 P1087 P1088 VVEL system
 P1090 P1093 VVEL actuator motor
 P1091 VVEL actuat or motor relay
 P1217 Engine over temperature (OVERHEAT)
 P1650 Starter motor relay 2
 P1651 Starter motor relay
 P2101 Electric throttle control function
 P2118 Throttle control motor
 P1805 Brake switch
 P2100 P2103 Throttle control motor relay
 P2101 Electric throttle control function
3  P0011 P0021 Intake valve timing control  P0087, P0088, P0090 FRP control system
 P008A Low fuel pressure control system
 P008B Low fuel pressure control system
 P0171 P0172 P0174 P0175 Fuel injection system function
 P0201 - P0208 Injector
 P0300 - P0308 Misfire
 P0420 P0430 Three way catalyst function
 P0456 EVAP control system (VERY SMALL LEAK)
 P0506 P0507 Idle speed control system
 P050E Cold start control
 P0524 Engine oil pressure
 P1148 P1168 Closed loop control
 P1212 TCS communication line
 P1421 Cold start control
 P1564 ASCD steering switch / ICC steering switch
 P1652 Starter motor system communication
 P2119 Electric throttle control actuator
 P1564 ASCD steering switch / ICC steering switch
 P1568 ICC command value
 P1572 ASCD brake switch / ICC brake switch
 P1574 ASCD vehicle speed sensor / ICC vehicle speed sensor
Priority Detected items (DTC)
DTC*1
Items
(CONSULT-III screen terms) SRT code Trip MIL
Reference
page
CONSULT-III
GST*
2ECM*3
U0101 0101 LOST COMM (TCM) — 1 ×EC-171
U0113 0113 CAN COMM CIRCUIT — 1 ×EC-173
U1001
1001*4CAN COMM CIRCUIT — 1 or 2 — EC-172
U1003 1003 CAN COMM CIRCUIT — 2 — EC-173
Revision: 2010 May2011 QX56