power steering INFINITI QX56 2011 Factory User Guide

SYSTEMADP-17
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
EXIT ASSIST FUNCTION
EXIT ASSIST FUNCTION : System DiagramINFOID:0000000006248309
EXIT ASSIST FUNCTION : System DescriptionINFOID:0000000006248310
 When exiting, the condition is satisfied, the seat is moved backward 40 mm (1.57 in) from normal sitting
position and the steering is moved to the most upper position.
 The seat slide amount and the steering oper ation at entry/exit operation can be changed.
NOTE:
 This function is set to ON before delivery (initial setting).
 Further information for the system setting procedure. Refer to ADP-54, "
SYSTEM SETTING : Description".
OPERATION PROCEDURE
1. Shift position P position.
2. Open the driver door with ignition switch in OFF position.
3. Driver seat and steering column will move to the exiting position.
OPERATION CONDITION
Satisfy all of the following items. The exit assist function is not performed if these items are not satisfied.
JMJIA3776GB
Item Request status
Ignition position OFF
System setting [Entry/exit assist function (seat/steering)] ON
Initialization Done
Switch inputs
 Power seat switch
 Tilt & telescopic switch
 Door mirror remote control switch
 Set switch
 Memory switch OFF
(Not operated)
A/T shift selector P position
Handle position LHD
Revision: 2010 May2011 QX56

SYSTEMADP-19
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
2. Driver seat and steering column will return from the exiting position to entry position.
OPERATION CONDITION
Satisfy all of the following items. The entry assist f unction is not performed if these items are not satisfied.
DETAIL FLOW
INTELLIGENT KEY INTERLOCK FUNCTION
Item Request status
Seat, steering column The vehicle is not moved after performing the
exit assist function.
Switch inputs
 Power seat switch
 Tilt & telescopic switch
 Door mirror control switch
 Set switch
 Memory switch OFF
(Not operated)
Vehicle speed 0 Km/h (0 MPH)
Sta rte r OFF
Transmission A/T
CONSULT-III Not connected
Order Input Output Control unit condition
1 Ignition switch — Driver seat control unit receives the signals of [ignition switch signal]
from BCM via CAN communication.
2— Motors
(Sliding, tilt)Driver side control unit operates the sliding motor when the operating
conditions are satisfied and requests the operations of tilt motor to
automatic drive positioner control unit via UART communication. The
automatic drive positioner operates each motor.
3 Sensors
(Sliding, tilt) —Each sensor monitors the operating positions of seat and steering,
and then stops the operation of each motor when each part reaches
the recorded address.
Revision: 2010 May2011 QX56

SYSTEMADP-21
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
DETAIL FLOW
Fail SafeINFOID:0000000006248315
The fail-safe mode may be activated if the following symptoms are observed.
Item Request status
Ignition position OFF
Intelligent key interlock function Registered
Steering lock unit status LOCK
Switch inputs
 Power seat switch
 Tilt & telescopic switch
 Door mirror control switch
 Set switch
 Memory switch OFF
(Not operated)
A/T shift selector P position
Order Input Output Control unit condition
1  Door unlock signal
(CAN)
 Key ID signal (CAN) —Driver seat control unit receives unlock signal and key ID signal from
BCM, when driver seat control unit is unlocked by Intelligent Key or
driver side door request switch.
2— — Driver seat control unit performs the seat slide and steering tilt move
directly to the exit assist function. Other loads move to the exit assist
function after performing memory function.
3 — — Driver seat control unit performs the entry assist function.
Operating in
fail-safe mode Malfunction Item
Related
DTC Diagnosis
Only manual functions operate normally. CAN communication U1000
ADP-56
CONTROL UNIT U1010ADP-57
EEPROM B2130ADP-66
Only manual functions, except door mirror, operate normally. UART communication B2128 ADP-64
Only manual functions, except seat sliding, operate normally. Seat sliding output B2112ADP-58
Only manual functions, except seat reclining, operate normally. Seat reclining output B2113ADP-60
Only manual functions, except steering tilt, operate normally. Steering column tilt output B2116ADP-62
Revision: 2010 May2011 QX56

ADP-28
< ECU DIAGNOSIS INFORMATION >
DRIVER SEAT CONTROL UNIT
4
(R/L) Ground Reclining sensor sig-
nal Input Seat reclining Operate
Other than the
above
0 or 5
5
(R/B) Ground
Telescopic sensor sig-
nal Input
Steering telescop-
ic Operate
Other than the
above
0 or 5
6
(R/W) Ground Memory switch 2 sig-
nal Input Memory switch 2 Press 0
Other than the
above
5
7
(R/G) Ground Memory indicator 2
signal OutputMemory indicator
2 Illuminate 1
Other than the
above
12
8
(SB) Ground Sliding switch back-
ward signal Input Sliding switch Operate
(backward)
0
Other than the
above 12
9
(L) Ground
Reclining switch back-
ward signal Input Reclining switch Operate
(backward)
0
Other than the
above 12
10
(L/B) Ground Lifting switch (front)
down signal
InputLifting switch
(front) Operate
(down)
0
Other than the
above 12
11
(L/W) Ground Lifting switch (rear)
down signal InputLifting switch
(rear) Operate
(down)
0
Other than the
above 12
12
(L/R) Ground Sensor power supply Output — 12
17
(V)
—CAN-L — — —
18
(B/W) Ground Sliding sensor signal Input Seat sliding Operate
Other than the
above
0 or 5
JMJIA0119ZZ
JMJIA0119ZZ
JMJIA0119ZZ
Revision: 2010 May2011 QX56

ADP-30
< ECU DIAGNOSIS INFORMATION >
DRIVER SEAT CONTROL UNIT
Fail Safe
INFOID:0000000006248318
The fail-safe mode may be activated if the following symptoms are observed.
33
(R) Ground Battery power supply Input — Battery voltage
34
(B) Ground Sliding motor back-
ward output signal Output Seat sliding Operate
(backward)
12
Other than the
above 0
35
(G) Ground
Reclining motor for-
ward output signal Output Seat reclining Operate
(forward)
12
Other than the
above 0
36
(L) Ground Lifting motor (front)
down output signal
Output Seat lifting (front) Operate
(down)
12
Other than the
above 0
38
(GR) Ground Sliding motor forward
output signal Output Seat sliding Operate
(forward)
12
Other than the
above 0
39
(Y) Ground
Reclining motor back-
ward output signal Output Seat reclining Operate
(backward)
12
Other than the
above 0
40
(W) Ground Lifting motor (front) up
output signal
Output Seat lifting (front) Operate
(up)
12
Other than the
above 0
41
(V) Ground Lifting motor (rear) up
output signal Output Seat lifting (rear) Operate
(up)
12
Other than the
above 0
42
(P/B) Ground
Lifting motor (rear)
down output signal Output Seat lifting (rear) Operate
(down)
12
Other than the
above 0
43
(LG) Ground Ground — — 0
Operating in
fail-safe mode Malfunction ItemRelated
DTC Diagnosis
Only manual functions operate normally. CAN communication U1000
ADP-56
CONTROL UNIT U1010ADP-57
EEPROM B2130ADP-66
Only manual functions, except door mirror, operate normally. UART communication B2128 ADP-64
Only manual functions, except seat sliding, operate normally. Seat sliding output B2112ADP-58
Only manual functions, except seat reclining, operate normally. Seat reclining output B2113ADP-60
Only manual functions, except steering tilt, operate normally. Steering column tilt output B2116ADP-62
Revision: 2010 May2011 QX56

ADP-34
< ECU DIAGNOSIS INFORMATION >
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
24
(BR/Y) Ground Door mirror motor (driver
side) left output signal
Output Door mirror (LH) Operate
(left)
12
Other than the
above 0
25
(W/R) Ground Battery power supply Input — Battery voltage
26
(L) Ground Telescopic motor back-
ward output signal
OutputSteering tele-
scopic Operate
(backward)
12
Other than the
above 0
27
(P) Ground Tilt & telescopic sensor
power supply
Output — 12
28
(G) Ground Tilt motor down output
signal
Output Steering tilt Operate
(down)
12
Other than the
above 0
29
(W/B) Ground Tilt motor up output sig-
nal
OutputSteering tilt
Operate
(up)
12
Other than the
above 0
Telescopic motor for-
ward output signal Steering tele-
scopicOperate
(forward)
12
Other than the
above 0
30
(B) Ground Ground — — 0
Te r m i n a l N o .
(wire color) Description
ConditionVoltage (V)
(Approx.)
+ - Signal name Input/
Output
Revision: 2010 May2011 QX56

ADP-62
< DTC/CIRCUIT DIAGNOSIS >
B2116 TILT MOTOR
B2116 TILT MOTOR
DTC LogicINFOID:0000000006248346
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.STEP 1
Turn ignition switch ON.
>> GO TO 2.
2.STEP 2
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-62, "DiagnosisProcedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006248347
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Erase the DTC.
4. Perform DTC confirmation procedure. Refer to ADP-62, "
DTC Logic".
Is the DTC displayed again?
YES >> GO TO 2.
NO >> Check intermittent incident. Refer to GI-40, "
Intermittent Incident".
2.CHECK TILT MOTOR CIRCUIT (POWER SHORT)
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and tilt motor connector.
3. Check voltage between tilt motor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK AUTOMATIC DRIVER POSITION ER CONROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit connector.
2. Check voltage between automatic drive posit ioner control unit harness connector and ground.
DTC No.Trouble diagnosis
name DTC detecting condition Possible cause
B2116 STEERING TILT The automatic drive positioner control unit detects
the output of tilt motor output terminal for 0.1 second
or more even if the tilt switch is not input.  Automatic drive positioner con-
trol unit
 Tilt motor harn ess is shorted
(+)
(-)Voltage (V)
(Approx.)
Tilt motor
Connector Terminals
M116 1
Ground 0
2
Revision: 2010 May2011 QX56

AV
COMPONENT PARTSAV-11
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
Video distributor  It receives the image signal and sound signal from the AV control unit and then
transmits it to the headrest display unit.
 It receives the image signal and sound signal from the auxiliary input jacks and then transmits it to the headrest display unit.
 Switches image and sound output to headrest display unit, inputting image switch
signal from headrest display unit via hard wire.
Front auxiliary input jacks Image signal and sound signal of auxiliary input is transmitted to AV control unit.
Rear auxiliary input jacks
(Mobile entertainment system) Image signal and sound signal of auxiliary input is transmitted to video distributor.
BOSE amp. Inputs sound signal from AV control unit, and outputs sound signal to each speaker.
Front door speaker  Outputs sound signal from BOSE amp.
 Outputs high, mid and low range sounds.
Rear door speaker  Outputs sound signal from BOSE amp.
 Outputs high, mid and low range sounds.
Squawker  Outputs sound signal from BOSE amp.
 Outputs high and mid range sounds.
Rear door tweeter  Outputs sound signal from BOSE amp.
 Outputs high range sounds.
Roof speaker  Outputs sound signal from BOSE amp.
 Outputs high and mid range sounds.
Center speaker  Outputs sound signal from BOSE amp.
 Outputs high and mid range sounds.
Woofer  Outputs sound signal from BOSE amp.
 Outputs low range sounds.
Multifunction switch  Operation panel is equipped with the centralized switch where audio, auxiliary in-
put and navigation, etc. operations are integrated.
 Connected with preset switch via hardwire and operation signal is transmitted to AV control unit via AV communication.
Preset switch  Operation panel is equipped with the centralized switch where audio and air con-
ditioner, etc. operations are integrated.
 Connected with multifunction switch via hardwire, and operation signal is transmit- ted to AV control unit via AV communication.
 The disk ejection operating signal is performed by hardwire.
Steering switch  Operations for audio, hands-free phone and navigation, etc. are possible.
 Steering switch signal (operation signal) is output to AV control unit.
Around view monitor control unit  It supplies power to front camera, rear camera, and side camera. And then it su-
perimposes the images from each camera and outputs them to front display unit.
 Superimpose the guiding line, predicted course line and sonar indicator to the
camera image that outputs to front display unit.
 It performs the reception/transmission of communication signal with each camera.
 It transmits the sonar operation signal from sonar control unit and receives the so- nar information from sonar control unit via AV communication.
 It transmits the information received/transmitted with sonar control unit via AV communication to AV control unit.
Front camera  It inputs the power supply from around view monitor control unit and outputs the
image of the vehicle front to around view monitor control unit.
 It performs the reception/transmission of the communication signal with around view monitor control unit.
Rear camera  It inputs the power supply from around view monitor control unit and outputs the
image of the vehicle rear to around view monitor control unit.
 It performs the reception/transmission of the communication signal with around view monitor control unit.
Side camera LH  It inputs the power supply from around view monitor control unit and outputs the
image of the vehicle LH to around view monitor control unit.
 It performs the reception/transmission of the communication signal with around view monitor control unit.
Part name Description
Revision: 2010 May2011 QX56

AV-12
< SYSTEM DESCRIPTION >
COMPONENT PARTS
*1: Image signals cannot be received from iPod®.
Side camera RH It inputs the power supply from around view monitor control unit and outputs the
image of the vehicle RH to around view monitor control unit.
 It performs the reception/transmission of the communication signal with around view monitor control unit.
Infrared LED
(Auxiliary lighting)  It illuminates around the front RH wheel by the power supply from around view
monitor control unit to improve nighttime visibility of front-side view.
 The infrared LED is an invisible light ray.
Sonar control unit  It is connected with around view monitor control unit via AV communication and
receives the sonar operation signal from around view monitor control unit.
 It transmits the sonar detection status to around view monitor control unit via AV
communication.
 It judges the warning level according to the signal from corner sensor.
Corner sensor The obstacle distance is detected. The signal is transmitted to sonar control unit.
Steering angle sensor It is connected to the AV control unit and transmits the steering angle sensor signal
via CAN communication.
Microphone  Used for hands-free phone operation.
 Microphone signal is transmitted to AV control unit.
 Power (Microphone VCC) is supplied from AV control unit.
GPS antenna GPS signal is received and transmitted to AV control unit.
Satellite radio antenna Receives the satellite radio waves and outputs it to AV control unit.
Antenna amp.  Radio signal received by glass antenna (main) is amplified and transmitted to AV
control unit.
 Power (antenna amp. ON signal) is supplied from AV control unit.
USB connector Image signal
*1 and sound signal of USB input is transmitted to AV control unit.
Part name Description
Revision: 2010 May2011 QX56

AV-36
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Unfinished configurationThe writing of configuration data is incom-
plete.Write configuration data with CONSULT-III.
USB Controller Communication Error USB connection malfunction is detected. Check that the connection to the USB con-
nector is normal.
DVD Mechanism Communication Error AV control unit malfunction is detected.  If DVD can be played, then there is a
possibility of the detection of a temporary
malfunction.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
Steer. Angle Sensor Calibration Predictive course line center position ad-
justment of the steering angle sensor is in-
complete.Adjust the predictive course line center po-
sition of the steering angle sensor.
Refer to
AV- 3 9 , "
CONSULT-III Function".
Front Display Connection Error When either one of the following items are
detected:
 front display unit power supply and
ground circuits are malfunctioning.
 Serial communication circuits between AV control unit and front display unit are
malfunctioning.  Front display unit power supply and
ground circuits.
 Serial communication circuits between AV control unit and front display unit.
 AV COMM CIRCUIT
 2nd Display Co nnection Error When either one of the following items are
detected:
 video distributor power supply and
ground circuits are malfunctioning.
 headrest display unit LH power supply and ground circuits are malfunctioning.
 AV communication circuits between AV
control unit and headrest display unit LH
are malfunctioning.
 location recognition signal circuit be-
tween headrest display unit LH and
ground is malfunctioning.  Video distributor power supply and
ground circuits.
 Headrest display unit LH power supply and ground circuits.
 AV communication circuits between AV control unit and headrest display unit LH.
 Location recognition signal circuit be-
tween headrest display unit LH and
ground.
3rd Display Connection Error When either one of the following items are
detected:
 headrest display unit RH power supply
and ground circuits are malfunctioning.
 AV communication circuits between
headrest display unit LH and headrest
display unit RH are malfunctioning.
 location recognition signal circuit be- tween headrest display unit RH and
ground is malfunctioning.  Headrest display unit RH power supply
and ground circuits.
 AV communication circuits between headrest display unit LH and headrest
display unit RH.
 Location recognition signal circuit be- tween headrest display unit RH and
ground.
AM/FM antenna amplifier short to ground Radio antenna amp. ON signal circuit mal-
function is detected.Radio antenna amp. ON signal circuit be-
tween AV control unit and antenna amp.
AM/FM antenna amplifier open
Ext_Amp_ON output terminal short to
ground BOSE amp. ON signal circuit malfunction is
detected.BOSE amp. ON signal circuit between AV
control unit and BOSE amp.
Ext_Amp_ON output terminal :open
GPS Antenna Error GPS antenna connection malfunction is de-
tected.Check the connection of the GPS antenna
connector.
XM Antenna Connection Error Satellite radio antenna connection malfunc-
tion is detected.
Satellite radio antenna disconnection.
USB electric current Error Detection of overcurrent in USB connector. Check USB harness between the AV con-
trol unit and USB connector.
Error item Description Possible malfunction factor/Action to take
Revision: 2010 May2011 QX56