INFINITI QX56 2011 Factory Service Manual

AV
AV CONTROL UNITAV-53
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P16
(Y/L) 15
(B) Steering switch signal B Input Ignition
switch
ON Keep pressing VOL DOWN
switch.
0 V
Keep pressing VOL UP
switch. 1.0 V
Keep pressing switch. 2.0 V
Keep pressing switch. 3.0 V
Except for above. 5.0 V
19
(Y/R) Ground Battery power supply Input Ignition
switch
OFF — Battery voltage
20
(B) Ground Ground — Ignition
switch ON —0 V
26
(LG) Ground AUX image signal Input Ignition
switch ON At front AUX image is dis-
played.
29
(W/B) Ground Disk eject signal Input Ignition
switch
ON Pressing the eject switch. 0 V
Except for above. 5.0 V
30
(R/W) Ground Mode change signal Output Ignition
switch ON Driver's Audio Stage ON 0 V
Driver's Audio Stage OFF 8.5 V
33
(L) Ground
Composite image signal
ground —Ignition
switch ON —0 V
34
(P) Ground Composite image signal Output Ignition
switch ON When DVD, USB or front
AUX image is displayed on
headrest display unit LH or
RH.
46
(V) Ground AUX image signal ground — Ignition
switch ON —0 V
47 — Shield — — — —
49
(R/W) Ground Switch ground — Ignition
switch
ON —0 V
53 — Shield — — — —
65
(W) Ground Parking brake signal Input Ignition
switch ON Parking brake is applied. 0 V
Parking brake is released. 4.5 V
67
(W) Ground Composite image signal
ground —Ignition
switch ON —0 V
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
SKIB2251J
SKIB2251J
Revision: 2010 May2011 QX56

AV-54
< ECU DIAGNOSIS INFORMATION >
AV CONTROL UNIT
68
(R) Ground Composite image signal Output Ignition
switch ON At DVD image is displayed.
72
(Y/G) Ground Microphone VCC Output Ignition
switch ON —5.0 V
73
(Y/G) Ground Communication signal
(CONT
→DISP) OutputIgnition
switch ON When adjusting display
brightness.
74
(P) —CAN–L Input/
Output —— —
75
(LG) —
AV communication signal
(L) Input/
Output —— —
76
(LG) —AV communication signal
(L) Input/
Output —— —
79
(L/O) Ground Dimmer signal Input Ignition
switch ON Either of the following con-
ditions
 Lighting switch is OFF
 Lighting switch is 1st or
2nd, and the area around
the vehicle is bright
(shine a light on the opti-
cal sensor) 0 V
Lighting switch is 1st or
2nd, and the area around
the vehicle is dark (block
the light from the optical
sensor) 12.0 V
80
(GR/L) Ground Ignition signal Input Ignition
switch
ON — Battery voltage
81
(R/Y) Ground Reverse signal Input Ignition
switch ON Selector lever is in R posi-
tion.
12.0 V
Selector lever is in other
than R position. 0 V
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
SKIB2251J
PKIB5039J
Revision: 2010 May2011 QX56

AV
AV CONTROL UNITAV-55
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P
82
(BR/W) GroundVehicle speed signal (8-
pulse) InputIgnition
switch ON When vehicle speed is ap-
prox. 40 km/h (25 MPH) NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
83 — Shield — — — —
84
(W/B) Ground Composite image synchro-
nizing signal
OutputIgnition
switch ON At DVD image is displayed.
87
(Y/L) 71 Microphone signal Input Ignition
switch ON Give a voice.
88 — Shield — — — —
89
(Y/L) Ground Communication signal
(DISP
→CONT) InputIgnition
switch ON When adjusting display
brightness.
90
(L) —CAN–H Input/
Output —— —
91
(SB) —AV communication signal
(H) Input/
Output —— —
92
(SB) —
AV communication signal
(H) Input/
Output —— —
104 (W) 11 9
(W/L) AUX sound signal LH Input Ignition
switch ON When front AUX mode is
selected.
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
JSNIA0012GB
SKIB2251J
PKIB5037J
PKIB5039J
SKIB3609E
Revision: 2010 May2011 QX56

AV-56
< ECU DIAGNOSIS INFORMATION >
AV CONTROL UNIT
106(W) 120
(R) Sound signal LH Output Ignition
switch ON When DVD or USB mode is
selected on headrest dis-
play unit LH or RH.
107 (B) 121
(G) Sound signal RH Output Ignition
switch ON When DVD or USB mode is
selected on headrest dis-
play unit LH or RH.
11 7 — S h i e l d — — — —
11 8 (O) 11 9
(W/L) AUX sound signal RH Input Ignition
switch ON When front AUX mode is
selected.
122 — Shield — — — —
129 (G) — USB ground — — — —
130 (R) — USB D
− signal — — — —
131 (W) — V BUS signal — — — —
132 (L) — USB D+ signal — — — —
133 — Shield — — — —
150 — FM sub Input — — —
151 — AM-FM main Input — — —
152 Ground Antenna amp. ON signal Input Ignition
switch ON —12.0 V
153 Ground GPS antenna signal Input Ignition
switch ON Not connected GPS anten-
na connector.
5.0 V
154 — Shield — — — —
157 Ground RGB digital image signal
(
− ) OutputIgnition
switch
ON Not connected connector. 1.3 V
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
SKIB3609E
SKIB3609E
SKIB3609E
Revision: 2010 May2011 QX56

AV
AV CONTROL UNITAV-57
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P
Fail-SafeINFOID:0000000006216226
When the ambiance temperature becomes extremely low or extremely high, AV control unit displays the mes-
sage and limits the AV control unit function.
FAIL-SAFE CONDITIONS
When the ambiance temperature is −20 °C ( −4 °F) or lower, or when it is 70 °C (158 °F) or higher
Display
The messages displayed on fail-safe conditions are as shown below:
DESCRIPTION OF CONTROLS
Ability Operation Mode
There is an ability operation mode for Fail-safes due to low or high ambiance temperature.
If HDD data can be read, fail-safe is shown, then normal displays are displayed only for functions which can be
operated.
RELEASE CONDITIONS OF FAIL-SAFE
Fail-safe is released on following conditions and normal mode is restored.
When The Temperature of HDD Is Low or High
If the ambient temperature becomes out of fa il-safe condition range, normal mode is restored.
DTC IndexINFOID:0000000006216227
SELF-DIAGNOSIS RESULTS DISPLAY ITEM
158 GroundRGB digital image signal
(+)
OutputIgnition
switch ON Not connected connector. 1.3 V
159 Ground Satellite radio antenna sig-
nal InputIgnition
switch ON Not connected satellite an-
tenna connector.
5.0 V
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
Fail-safe mode Display (display of the fail-safe condition)
When HDD temperature is low HDD system is experienci
ng problems due to extreme low temperature.
Normal operation will resume when temperature rises.
When HDD temperature is high HDD system is experienci
ng problems due to extreme high temperature.
Normal operation will resume when temperature drops.
Function When Fail-safe Function is activated
Air conditioner Operation Only multifunction switch (preset switch) can be operated.
Display
 LED of multifunction switch (preset switch) illuminates.
 Aimed temperature, blow angle, and flow rate are displayed in simplified mode.
Audio Operation Only ON/OFF and volume control operations by multifunction switch (preset switch) are possible.
Display No display (“Fail-safe mode” is displayed)
Camera Operation Image tone cannot be controlled.
Display Cannot be superimposed. (warning display, tone control display)
Hands-free phone Operation Cannot be operated.
Navigation Operation Cannot be operated.
Self diagnosis The display in simplified mode of fail-safe condition
CONSULT-III diagnosis Cannot be operated.
Revision: 2010 May2011 QX56

AV-58
< ECU DIAGNOSIS INFORMATION >
AV CONTROL UNIT
DTC Display item Refer to
U1000 CAN COMM CIRCUIT [U1000] AV- 11 8 , "
DiagnosisProcedure"
U1010 CONTROL UNIT (CAN) [1010] AV- 11 9 , "DTC Logic"
U1200 Cont Unit [U1200]AV- 1 2 0 , "DTC Logic"
U1201 GYRO NO CONN [U1201]AV- 1 2 1 , "DTC Logic"
U1202 G-SENSOR NO CONN [U1202]AV- 1 2 2 , "DTC Logic"
U1204 GPS COMM [U1204]AV- 1 2 3 , "Diagnosis Procedure"
U1205 GPS ROM [U1205]AV- 1 2 4 , "Diagnosis Procedure"
U1206 GPS RAM [U1206]AV- 1 2 5 , "Diagnosis Procedure"
U1207 GPS RTC [U1207]AV- 1 2 6 , "Diagnosis Procedure"
U1216 CAN CONT [U1216] AV- 1 2 7 , "DTC Logic"
U1217 BLUETOOTH MODULE [U1217]AV- 1 2 8 , "DTC Logic"
U1218 HDD CONN [U1218]AV- 1 2 9 , "Diagnosis Procedure"
U1219 HDD READ [U1219]AV- 1 3 0 , "Diagnosis Procedure"
U121A HDD WRITE [U121A] AV- 1 3 1 , "Diagnosis Procedure"
U121B HDD COMM [U121B]AV- 1 3 2 , "Diagnosis Procedure"
U121C HDD ACCESS [U121C] AV- 1 3 3 , "Diagnosis Procedure"
U121D DSP CONN [U121D]AV- 1 3 4 , "Diagnosis Procedure"
U121E DSP COMM [U121E]AV- 1 3 5 , "Diagnosis Procedure"
U1225 USB CONTROLLER [U1225] AV- 1 3 6 , "DTC Logic"
U1227 DVD COMM [U1227]AV- 1 3 7 , "Diagnosis Procedure"
U1228 SUB CPU CONN [U1228] AV- 1 3 8 , "DTC Logic"
U1229 iPod CERTIFICATION [U1229]AV- 1 3 9 , "DTC Logic"
U122A CONFIG UNFINISH [U122A]AV- 1 4 0 , "Diagnosis Procedure"
U122E Built-in AUDIO CONN [U122E] AV- 1 4 1 , "DTC Logic"
U1232 ST ANGLE SEN CALIB [1232]AV- 1 4 2 , "Diagnosis Procedure"
U1243 FRONT DISP CONN [U1243]AV- 1 4 3 , "Diagnosis Procedure"
U1244 GPS ANTENNA CONN [U1244]AV- 1 4 5 , "Diagnosis Procedure"
U1258 XM ANTENNA CONN [U1258]AV- 1 4 6 , "Diagnosis Procedure"
U125A 3RD DISP CONN [U125A] AV- 1 4 7 , "Diagnosis Procedure"
U1263 USB OVERCURRENT [U1263]AV- 1 4 8 , "Diagnosis Procedure"
U1264ANTENNA AMP TERMINAL [OPEN or
SHORT] [U1264] AV- 1 4 9 , "Diagnosis Procedure"
U1265
AMP ON TERMINAL [GND-SHORT or VB-
SHORT] [U1265] AV- 1 5 0 , "Diagnosis Procedure"
U1310 CONTROL UNIT (AV) [U1310]
AV- 1 5 2 , "DTC Logic"
Revision: 2010 May2011 QX56

AV
AV CONTROL UNITAV-59
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P
U1300
U1240  AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
AV- 1 5 1 , "
Description"
U1300
U1246 AV COMM CIRCUIT [U1300]
 VIDEO DIST CONN [U1246]
U1300
U125B  AV COMM CIRCUIT [U1300]
 AROUND CAMERA CONN [U125B]
U1300
U125C  AV COMM CIRCUIT [U1300]
 SONAR CONN [U125C]
U1300
U1240
U125C U125B  AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
 SONAR CONN [U125C]
 AROUND CAMERA CONN [U125B]
U1300
U1240
U125C U125B
U1246  AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
 SONAR CONN [U125C]
 AROUND CAMERA CONN [U125B]
 VIDEO DIST CONN [U1246]
DTC Display item Refer to
Revision: 2010 May2011 QX56

AV-60
< ECU DIAGNOSIS INFORMATION >
FRONT DISPLAY UNIT
FRONT DISPLAY UNIT
Reference ValueINFOID:0000000006216228
TERMINAL LAYOUT
PHYSICAL VALUES
JSNIA2241ZZ
Terminal
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
6—Shield —— — —
7—Shield —— — —
8
(W) Ground Camera image signal Input Ignition
switch ON At camera image is dis-
played.
9
(Y/L) Ground Communication signal
(DISP
→CONT) OutputIgnition
switch ON When adjusting display
brightness.
10
(Y/G) Ground Communication signal
(CONT
→DISP) InputIgnition
switch ON When adjusting display
brightness.
11
(Y/R) Ground Battery power supply Input Ignition
switch
OFF — Battery voltage
12
(B) Ground Ground — Ignition
switch ON —0 V
SKIB2251J
PKIB5039J
PKIB5039J
Revision: 2010 May2011 QX56

AV
FRONT DISPLAY UNITAV-61
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P18
(R) Ground Composite image signal Input Ignition
switch ON At DVD image is displayed.
19
(W) Ground Composite image signal
ground —Ignition
switch ON —0 V
20
(W/B) Ground Composite image synchro-
nizing signal InputIgnition
switch ON —
22 — Shield — — — —
23
(V) Ground ACC power supply Input Ignition
switch ACC — Battery voltage
27 — RGB digital image signal
(
− ) Input — — —
28 — RGB digital image signal
(+)
Input — — —
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
SKIB2251J
SKIB0825E
Revision: 2010 May2011 QX56

AV-62
< ECU DIAGNOSIS INFORMATION >
HEADREST DISPLAY UNIT
HEADREST DISPLAY UNIT
Reference ValueINFOID:0000000006216229
TERMINAL LAYOUT
PHYSICAL VALUES
JPNIA0007ZZ
Terminal
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
1
(L) Ground Ground — Ignition
switch ON —0 V
2
(V) Ground Battery power supply Input Ignition
switch
OFF — Battery voltage
3
(GR) Ground Ground — Ignition
switch ON —0 V
4
(L/R) Ground Battery power supply Input Ignition
switch OFF — Battery voltage
9
(B/R) Ground
Location recognition signal
for headrest display unit RH InputIgnition
switch
ON —0 V
10
(L/B) Ground Location recognition signal
for headrest display unit LH
InputIgnition
switch ON —0 V
11
(B) —AV communication signal
(H) Input/
Output —— —
12
(G) —AV communication signal
(H) Input/
Output —— —
13
(R) —
AV communication signal
(L) Input/
Output —— —
14
(W) —AV communication signal
(L) Input/
Output —— —
15 — Shield — — — —
18
(W/R) Ground ACC signal Input Ignition
switch OFF — 3.3 V
Ignition switch
ACC —0 V
Revision: 2010 May2011 QX56