INFINITI QX56 2011 Factory Service Manual

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-33
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
A comparison check can be made of each actual vehicle signal and
the signals recognized by the system.
Sp ea ke r Tes t
Select “SPEAKER DIAGNOSIS” to display the Speaker Diagnosis
screen. Press “Start” to generate a test tone in a speaker. Press
“Start” to generate a test tone in the next speaker. Press “Stop” to
stop the test tones.
Navigation
STEERING ANGLE ADJUSTMENT
JSNIA2991ZZ
Diagnosis item Display Vehicle status Remarks
Vehicle speed ON Vehicle speed >= 8 km/h (5 MPH)
Changes in indication may be delayed. This is normal.
OFF Vehicle speed < 8 km/h (5 MPH)
Parking brake ON Parking brake is applied.
OFF Parking brake is released.
Lights ON
Block the light from the auto light
optical sensor when the lighting
switch is 1st or 2nd.
—
OFF Either of the following conditions.
 Lighting switch is OFF
 Expose the auto light optical sen-
sor to light when the lighting
switch is 1st or 2nd.
Ignition ON Ignition switch is ON.
—
OFF Ignition switch is in ACC position.
Reverse ON Selector lever is in “R” position.
Changes in indication may be delayed. This is normal.
OFF Selector lever is in other than “R”
position.
Side view Switch OFF — This item is displayed, but cannot be monitored.
Room Lamp OFF — This item is displayed, but cannot be monitored.
JPNIA1828ZZ
Revision: 2010 May2011 QX56

AV-34
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
The steering angle output value detected with the gyroscope is
adjusted.
SPEED CALIBRATION
During normal driving, distance error caused by tire wear and tire
pressure change is automatically adjusted for by the automatic dis-
tance correction function. This function, on the other hand, is for
immediate adjustment, in cases such as driving with tire chain fitted
on tires.
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-di agnosis start because of this situation.
The error record displays the time and place of the most recent occurrence of that error. However, take note of
the following points.
 If there is a malfunction with the GPS antenna circuit board in the AV control unit, the correct date and time
of occurrence may not be able to be displayed.
 Place of the error occurrence is represented by the posit ion of the current location mark at the time an error
occurred. If current location mark has deviated from t he correct position, then the place of the error occur-
rence cannot be located correctly.
 The frequency of occurrence is displayed in a count up manner. The actual count up method differs depend- ing on the error item.
Count up method A
 The counter resets to 0 if an error occurs when igniti on switch is turned ON. The counter increases by 1 if
the condition is normal at a next ignition ON cycle.
 The counter upper limit is 39. Any counts exceeding 39 are ignored.“ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Count up method B
 The counter increases by 1 if an error occurs when i gnition switch is ON. The counter will not decrease even
if the condition is normal at the next ignition ON cycle.
 The counter upper limit is 50. Any counts exceeding 50 are ignored. “ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
JSNIA2179ZZ
JSNIA2180ZZ
Display type of occur-
rence frequency Error history display item
Count up method A CAN communication line, control unit (CAN), AV communication line, control unit (AV)
Count up method B Other than the above
Revision: 2010 May2011 QX56

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-35
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
Error item
Some error items may be displayed simultaneously accordi ng to the cause. If some error items are displayed
simultaneously, the detection of the cause can be per formed by the combination of display items
JPNIA1788GB
Error item Description Possible malfunction factor/Action to take
CAN COMM CIRCUIT CAN communication malfunction is detect-
ed.Perform diagnosis with CONSULT-III, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
Refer to
AV- 3 9 , "
CONSULT-III Function".
CONTROL UNIT (CAN) CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit if the malfunc-
tion occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
CONTROL UNIT (AV)
AV communication circuit initial diagnosis
malfunction is detected.
FLASH-ROM Error Of Control Unit
AV control unit malfunction is detected.
Connection Of Gyro
Connection of G Sensor
CAN Controller Memory Error
Bluetooth Module Connection Error
Sub CPU Connection Error
Audio connection error
DSP Connection Error
AV control unit malfunction is detected. If a disc can be played, then there is a
possibility of the detection of a temporary
malfunction.
 Replace the AV control unit if the mal-
function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
DSP Communication Error
HDD Connection Error
AV control unit malfunction is detected. If the music box function has no malfunc-
tions, then there is a possibility of the de-
tection of a temporary malfunction.
 Replace the AV control unit if the mal-
function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
HDD Read Error
HDD Write Error
HDD Communication Error
HDD Access Error
GPS Communication Error
GPS malfunction is detected. An intermittent error caused by strong ra-
dio interference may be detected unless
any symptom (GPS reception error, etc.)
occurs.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
GPS ROM Error
GPS RAM Error
GPS RTC Error
Revision: 2010 May2011 QX56

AV-36
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Unfinished configurationThe writing of configuration data is incom-
plete.Write configuration data with CONSULT-III.
USB Controller Communication Error USB connection malfunction is detected. Check that the connection to the USB con-
nector is normal.
DVD Mechanism Communication Error AV control unit malfunction is detected.  If DVD can be played, then there is a
possibility of the detection of a temporary
malfunction.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
Steer. Angle Sensor Calibration Predictive course line center position ad-
justment of the steering angle sensor is in-
complete.Adjust the predictive course line center po-
sition of the steering angle sensor.
Refer to
AV- 3 9 , "
CONSULT-III Function".
Front Display Connection Error When either one of the following items are
detected:
 front display unit power supply and
ground circuits are malfunctioning.
 Serial communication circuits between AV control unit and front display unit are
malfunctioning.  Front display unit power supply and
ground circuits.
 Serial communication circuits between AV control unit and front display unit.
 AV COMM CIRCUIT
 2nd Display Co nnection Error When either one of the following items are
detected:
 video distributor power supply and
ground circuits are malfunctioning.
 headrest display unit LH power supply and ground circuits are malfunctioning.
 AV communication circuits between AV
control unit and headrest display unit LH
are malfunctioning.
 location recognition signal circuit be-
tween headrest display unit LH and
ground is malfunctioning.  Video distributor power supply and
ground circuits.
 Headrest display unit LH power supply and ground circuits.
 AV communication circuits between AV control unit and headrest display unit LH.
 Location recognition signal circuit be-
tween headrest display unit LH and
ground.
3rd Display Connection Error When either one of the following items are
detected:
 headrest display unit RH power supply
and ground circuits are malfunctioning.
 AV communication circuits between
headrest display unit LH and headrest
display unit RH are malfunctioning.
 location recognition signal circuit be- tween headrest display unit RH and
ground is malfunctioning.  Headrest display unit RH power supply
and ground circuits.
 AV communication circuits between headrest display unit LH and headrest
display unit RH.
 Location recognition signal circuit be- tween headrest display unit RH and
ground.
AM/FM antenna amplifier short to ground Radio antenna amp. ON signal circuit mal-
function is detected.Radio antenna amp. ON signal circuit be-
tween AV control unit and antenna amp.
AM/FM antenna amplifier open
Ext_Amp_ON output terminal short to
ground BOSE amp. ON signal circuit malfunction is
detected.BOSE amp. ON signal circuit between AV
control unit and BOSE amp.
Ext_Amp_ON output terminal :open
GPS Antenna Error GPS antenna connection malfunction is de-
tected.Check the connection of the GPS antenna
connector.
XM Antenna Connection Error Satellite radio antenna connection malfunc-
tion is detected.
Satellite radio antenna disconnection.
USB electric current Error Detection of overcurrent in USB connector. Check USB harness between the AV con-
trol unit and USB connector.
Error item Description Possible malfunction factor/Action to take
Revision: 2010 May2011 QX56

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-37
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
Vehicle CAN Diagnosis
 CAN communication status and error counter is displayed.
 The error counter displays “OK” if any malfunction was not
detected in the past and displays “0 ” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
 The error counter is erased if “Reset” is pressed.
NOTE:
“???” indicates UNKWN.
AV COMM Diagnosis
 AV COMM CIRCUIT
 Switches Connection Error When either one of the following items are
detected:
 multifunction switch power supply and
ground circuits were malfunctioning.
 AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.  Multifunction switch power supply and
ground circuits.
 AV communication circuits between AV control unit and multifunction switch.
 AV COMM CIRCUIT
 AVM Connection Error When either one of the following items are
detected:
 around view monitor control unit power
supply and ground circuits are malfunc-
tioning.
 AV communication circuits between AV control unit and around view monitor
control unit are malfunctioning.  Around view monitor control unit power
supply and ground circuits.
 AV communication circuits between AV control unit and around view monitor
control unit.
 AV COMM CIRCUIT
 Sonar Connection Error When either one of the following items are
detected:
 sonar control unit power supply and
ground circuits are malfunctioning.
 AV communication circuits between AV control unit and sonar control unit are
malfunctioning.  Sonar control unit power supply and
ground circuits.
 AV communication circuits between AV control unit and sonar control unit.
 AV COMM CIRCUIT
 Switches Connection Error
 Sonar Connection Error
 AVM Connection Error AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.AV communication circuits between AV
control unit and multifunction switch.
 AV COMM CIRCUIT
 Switches Connection Error
 Sonar Connection Error
 AVM Connection Error
 2nd Display Connection Error Error item Description Possible malfunction factor/Action to take
Items Display (Current)
Malfunction counter
(Past)
Tx(HVAC) OK / ??? OK / 0 – 39
Rx(ECM) OK / ??? OK / 0 – 39
Rx(Cluster) OK / ??? OK / 0 – 39
Rx(HVAC) OK / ??? OK / 0 – 39
Rx(USM) OK / ??? OK / 0 – 39
Rx(TPMS) OK / ??? OK / 0 – 39
Rx(STRG) OK / ??? OK / 0 – 39
Rx(ACC) OK / ??? OK / 0 – 39
RX(VDC) OK / ??? OK / 0 – 39
JSNIA2391ZZ
Revision: 2010 May2011 QX56

AV-38
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
 Displays the communication status between AV control unit (mas-ter unit) and each unit.
 The error counter displays “OK” if any malfunction was not
detected in the past and displays “0 ” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
 The error counter is erased if “Reset” is pressed.
NOTE:
“???” indicates UNKWN
Hands-Free Phone
The hands-free phone reception volume adjustment and microphone
and speaker test functions are also available.
Camera.
Refer to AV-44, "On Board Diagnosis Function".
XM
 Change Channel
- Any necessary channels required to receive traffic information from
the satellite radio system can be set.
 Change Application ID
- Any application ID'-s required to receive traffic information from the satellite radio system can be set.
Delete Unit Connection Log
Items Status
(Current) Counter
(Past)
C Tx(ITM–PrimarySW) OK / ??? OK / 0 – 39
C Rx(PrimarySW–ITM) OK / ??? OK / 0 – 39
C Rx(AVM–ITM) OK / ??? OK / 0 – 39
C Rx(Disp.3–Video Dist) OK / ??? / – OK / 0 – 39
C Rx(Video Dist–ITM) OK / ??? OK / 0 – 39
C Rx(Sonar–ITM) OK / ??? OK / 0 – 39
C Rx(Sonar–AVM) OK / ??? OK / 0 – 39
C Rx(R.RemoteCont–ITM) OK / ??? OK / 0 – 39
JSNIA2992ZZ
JSNIA2183ZZ
JSNIA2484ZZ
Revision: 2010 May2011 QX56

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-39
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
Deletes any unit connection records and error records from the AV
control unit memory. (Clear the records of the unit that has been
removed.)
Initialize Settings
“User Data Initialization” and “Accessory Number Initialization” are
possible.
CAUTION:
 Never perform Accessory Number Initialization except when configuration is unsuccessful.
 Accessory Number Initialization requires configuration. For
details, refer to AV-109, "
Description".
Version Information
Version information of the AV control unit is displayed.
CONSULT-III FunctionINFOID:0000000006216220
APPLICATION ITEMS
CONSULT-III performs the following functions via the communication with the AV control unit.
JSNIA2189ZZ
JSNIA2190ZZ
JSNIA2191ZZ
Diagnosis mode Description
Ecu Identification The part number of AV control unit can be checked.
Self Diagnostic Result Performs a diagnosis on the AV control unit and a connection diagnosis for the communication
circuit of the Multi AV system, and displays the current and past malfunctions collectively.
Revision: 2010 May2011 QX56

AV-40
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV Communication
When “AV communication” of “CAN Diag Support Monitor” is selected, the f\
ollowing function will be performed.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSIS RESULT
 In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
 The current malfunction indicates “CRNT”. The past malfunction indicates “PAST”.
 The timing is displayed as “0” if any of the e rror codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis Results Display Item
Data Monitor The diagnosis of vehicle signal that is input to the AV control unit can be performed.
Work Support Steering angle sensor can be adjusted.
Configuration Read and save the vehicle specification.
 Write the vehicle specification when replacing AV control unit.
Diagnosis mode Description
AV communication
AV&NAVI C/U
Displays the communication status from AV control unit to each unit as well as the error
counter.
AUDIO Displays the AV control unit communication status and the error counter.
Error item Description Possible malfunction factor/Action to take
CAN COMM CIRCUIT [U1000] CAN communication malfunction is detect-
ed.Refer to
AV- 11 8 , "
DiagnosisProcedure".
CONTROL UNIT (CAN) [U1010] CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit if the malfunc-
tion occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
CONTROL UNIT (AV) [U1310]
AV communication circuit initial diagnosis
malfunction is detected.
Cont Unit [U1200]
AV control unit malfunction is detected.
GYRO NO CONN [U1201]
G-SENSOR NO CONN [U1202]
CAN CONT [U1216]
BLUETOOTH MODULE [U1217]
SUB CPU CONN [U1228]
iPod CERTIFICATION [U1229]
Built-in AUDIO CONN [U122E]
HDD CONN [U1218]
AV control unit malfunction is detected. If the music box function has no mal-
functions, then there is a possibility of
the detection of a temporary malfunc-
tion.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
HDD READ [U1219]
HDD WRITE [U121A]
HDD COMM [U121B]
HDD ACCESS [U121C]
GPS COMM [U1204]
GPS malfunction is detected. An intermittent error caused by strong
radio interference may be detected un-
less any symptom (GPS reception error,
etc.) occurs.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
GPS ROM [U1205]
GPS RAM [U1206]
GPS RTC [U1207]
USB CONTROLLER [U1225] USB connection malfunction is detected.
Check that the connection to the USB con-
nector is normal.
Revision: 2010 May2011 QX56

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-41
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
DSP CONN [U121D] AV control unit malfunction is detected. If a disc can be played, then there is a
possibility of the detection of a tempo-
rary malfunction.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
DSP COMM [U121E]
DVD COMM [U1227] AV control unit malfunction is detected.  If DVD can be played, then there is a
possibility of the detection of a tempo-
rary malfunction.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
CONFIG UNFINISH [U122A] The writing of configuration data is incom-
plete.Write configuration data with CONSULT-
III.
ST ANGLE SEN CALIB [U1232] Predictive course line center position ad-
justment of the steering angle sensor is in-
complete.Adjust the predictive course line center po-
sition of the steering angle sensor.
Refer to
BRC-64, "
Work Procedure".
FRONT DISP CONN [U1243] When either one of the following items are
detected:
 front display unit power supply and
ground circuits are malfunctioning.
 serial communication circuits between
AV control unit and front display unit are
malfunctioning.  Front display unit power supply and
ground circuits.
 Serial communication circuits between AV control unit and front display unit.
GPS ANTENNA CONN [U1244] GPS antenna connection malfunction is
detected.Check the connection of the GPS antenna
connector.
 AV COMM CIRCUIT [U1300]
 VIDEO DIST CONN [U1246] When either one of the following items are
detected:
 video distributor power supply and
ground circuits are malfunctioning.
 headrest display unit LH power supply and ground circuits are malfunctioning.
 AV communication circuits between AV
control unit and headrest display unit LH
are malfunctioning.
 location recognition signal circuit be-
tween headrest display unit LH and
ground is malfunctioning.  Video distributor power supply and
ground circuits.
 Headrest display unit LH power supply
and ground circuits.
 AV communication circuits between AV control unit and headrest display unit
LH.
 Location recognition signal circuit be- tween headrest display unit LH and
ground.
3RD DISP CONN [U125A] When either one of the following items are
detected:
 headrest display unit RH power supply
and ground circuits are malfunctioning.
 AV communication circuits between headrest display unit LH and headrest
display unit RH are malfunctioning.
 location recognition signal circuit be- tween headrest display unit RH and
ground is malfunctioning.  Headrest display unit RH power supply
and ground circuits.
 AV communication circuits between Headrest display unit LH and headrest
display unit RH.
 Location recognition signal circuit be- tween headrest display unit RH and
ground.
XM ANTENNA CONN [U1258] Satellite radio antenna connection mal-
function is detected.Satellite radio antenna disconnection.
USB OVERCURRENT [U1263] Detection of overcurrent in USB connect-
er.Check USB harness between the AV con-
trol unit and USB connector.
ANTENNA AMP TERMINAL
[OPEN or SHORT]
[U1264] Radio antenna amp. ON signal circuit mal-
function is detected.
Radio antenna amp. ON signal circuit be-
tween AV control unit and antenna amp.
AMP ON TERMINAL
[GND-SHORT or VB-SHORT]
[U1265] BOSE amp. ON signal circuit malfunction
is detected.
BOSE amp. ON signal circuit between AV
control unit and BOSE amp.
Error item Description Possible malfunction factor/Action to take
Revision: 2010 May2011 QX56

AV-42
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DATA MONITOR
ALL SIGNALS
 Displays the status of the following vehicle signals inputted into the AV control unit.
 For each signal, actual signal can be compared with the condition recognized on the system.
 AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]When either one of the following items are
detected:
 multifunction switch power supply and
ground circuits are malfunctioning.
 AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.  Multifunction switch power supply and
ground circuits.
 AV communication circuits between AV control unit and multifunction switch.
 AV COMM CIRCUIT [U1300]
 AROUND CAMERA CONN [U125B] When either one of the following items are
detected:
 around view monitor control unit power
supply and ground circuits are malfunc-
tioning.
 AV communication circuits between AV control unit and around view monitor
control unit are malfunctioning.  Around view monitor control unit power
supply and ground circuits.
 AV communication circuits between AV control unit and around view monitor
control unit.
 AV COMM CIRCUIT [U1300]
 SONAR CONN [U125C] When either one of the following items are
detected:
 sonar control unit power supply and
ground circuits are malfunctioning.
 AV communication circuits between AV control unit and sonar control unit are
malfunctioning.  Sonar control unit power supply and
ground circuits.
 AV communication circuits between AV control unit and sonar control unit.
 AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
 SONAR CONN [U125C]
 AROUND CAMERA CONN [U125B] AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.AV communication circuits between AV
control unit and multifunction switch.
 AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
 SONAR CONN [U125C]
 AROUND CAMERA CONN [U125B]
 VIDEO DIST CONN [U1246] Error item Description Possible malfunction factor/Action to take
Display Item Display Vehicle status Remarks
VHCL SPD SIG On Vehicle speed >= 8 km/h (5 MPH)
Changes in indication may be delayed. This is
normal.
Off Vehicle speed < 8 km/h (5 MPH)
PKB SIG On Parking brake is applied.
Off Parking brake is released.
ILLUM SIG On
Block the light from the auto light op-
tical sensor when the lighting switch
is 1st or 2nd.
—
Off Either of the following conditions.
 Lighting switch is OFF
 Expose the auto light optical sen-
sor to light when the lighting switch
is 1st or 2nd.
IGN SIG On Ignition switch is ON
Off Ignition switch is in ACC position
REV SIG On Selector lever is in R position
Changes in indication may be delayed. This is
normal.
Off Selector lever is in any position other
than R
Revision: 2010 May2011 QX56